Technical Specifications

PRT Satin Flex Shield has been specially
engineered to optimize the benefits of PRT
tile and is the foundation treatment for the
VPI PRT Maintenance System when a
low gloss appearance is desired. When
used with VPI PRT Initial Deep Scrub, and
VPI PRT Cleaner - VPI PRT Satin Flex
Shield will assure the very best
performance in the toughest of commercial
applications. This is because PRT Satin
Flex Shield's high density molecular
construction actually chemically bonds
with the surface of PRT tile to not only
polish and protect, but also seal the surface
of the tile for many years of high
performance use. PRT Satin Flex Shield
also glides on and applies effortlessly
giving astonishing visual and functional
results unrivalled in the commercial flooring
industry.
PRT Satin Flex Shield is formulated from
crystal clear polymers that ensure it stays
clear and non-yellowing its entire life cycle.
Its state of the art flexible formulation is
designed to move and conform to pliable
floors allowing for ultimate protection over
an extended period of time. Properly
maintained with the VPI PRT System,
yields a forgiving repairable base capable
of withstanding 5 years of traffic before
needing a complete drawdown.
PRT Satin Flex Shield is quick leveling
and has excellent drying time. It will
withstand high traffic, yet is versatile
enough to just be cleaned and recoated.
PRT Satin Flex Shield is excellent for
hospitals, schools, office buildings, and
other high traffic floors where a flexible,
low gloss, maintenance program is desired.
DESCRIPTION USES / BENEFITS DIRECTIONS FOR USE
• Crystal Clear Polymer
Compression Technology
• Satin Gloss
• Non-yellowing
• Extended wear formula
• Less coats / less finish required
• Versatile - may be used on all
resilient tile, marble, terrazzo,
linoleum, rubber, sealed wood,
and cork.
• No seal required
• Easy to use
• Self leveling
• Excellent repairability - through
recoating
• Never Discolors
• Superior Durability & Coverage
• Slip resistance meets or exceeds
(ASTM D 2047-93) James Machine
0.5 minimum
NEW FLOORS: Prepare floor by following the
new floor VPI PRT Initial Deep Scrub label
instructions completely. Before applying PRT
Satin Flex Shield, floor surface must be clean,
dry and free of residue. After floor is completely
dry, apply PRT Satin Flex Shield in a uniform
thin coat using a rinsed out, clean, synthetic
finish mop. Allow to dry approximately 30 minutes
before applying the next coat. On high humidity
days allow more time. Apply a minimum of two
or three coats to maximize foundation. Floor
should appear non-glossy.
PREVIOUSLY COATED FLOORS Or
COMPLETE DRAWDOWN: Prepare floor by
following the VPI PRT Flex Stripper label
instructions completely. Before applying PRT
Satin Flex Shield, floor surface must be clean,
dry and free of residue. After floor is completely
dry, apply PRT Satin Flex Shield in a uniform
thin coat using a rinsed out, clean, synthetic
finish mop. Allow to dry approximately 30 minutes
before applying the next coat. On high humidity
days allow more time. Apply a minimum of two
or three coats to maximize foundation. Floor
should appear non-glossy.
DAILY MAINTENANCE: Sweep or dust mop the
floor to remove any large debris. (Use a water
based treatment only). Damp mop or automatic
scrub using a properly diluted solution of PRT
Cleaner and a RED pad.
PERIODIC MAINTENANCE: Sweep or dust mop
the floor to remove any large debris. (Use a water
based treatment only). Damp mop or automatic
scrub using a properly diluted solution of PRT
Cleaner and a RED pad. Floor can be recoated
to rejuvenate as necessary. To do so, damp mop
or automatic scrub using a properly diluted
solution of PRT Cleaner and a RED pad. Rinse
with clear water, and allow to dry. Floor surface
must be clean, dry and free of residue before
PRT Satin Flex Shield is applied again. Apply 1
- 2 coats following directions above.
SPECIFICATIONS
Toll Free: 800-874-4240 www.vpiflooring.com
EXTREME PERFORMANCE SATIN FLOOR PROTECTANT
PRT Earthtones, simply the most durable & beautiful commercial floor on the market today.....
Color ..........................Liquid White
Color Dried .............. Crystal Clear
Coverage ........... 2,500 sq. ft. gal.
Gloss (Gardner) .......... 1 Coat 30
2 Coats 35 Plus
Total Solids .......................25.0 %
pH ..................................7.7 - 8.5
Leveling ..................... Outstanding
Heel Mark Resistance ... Excellent
Detergent Resistance .... Excellent
Powdering Resistance ... Excellent
Slip Resistance............... Excellent
**NOT FOR USE ON VPI ESD TILE**
Item# 06401G