Series 5100/6100™ Voice/Data Router Web Interface Manual
Trademarks and copyrights All trademarks and registered trademarks listed belong to their respective owners. Vpacket, Vpacket Communications, and the Vpacket 5100/6100 Series Voice/Data Router are registered trademarks of Vpacket Communications, Inc., Milpitas, California. Vpacket Communications, Inc.
About this manual
About this manual ii Vpacket 5100/6100 Series Web Interface Manual
Content summary Audience This manual is written for the technical staff of a service provider, who are responsible for the installation and configuration of a Vpacket 5100/6100 Voice/Data Router (VDR). These users include, but are not limited to, network technicians, systems administrators, and network operation staff. Content summary This manual contains all of the information you need to configure the data and voice features of a 5100/6100 VDR via the WEB interface.
About this manual Conventions This manual uses typeface, syntax, and messages to alert you to information of special interest. Typefaces Table 2 lists the typefaces that are used in this manual. Table 2.
Related documentation Cautions Cautions are information requiring extra attention. For example: Caution. No system-level confirmation message appears during the deletion. ! Warnings Warnings are information that, if not followed, could result in injury or equipment damage. For example: Warning. Use of longer screws could result in damage to internal components.
About this manual Contact information For more information about the Vpacket 5100/6100 Series VDRs, please contact us using any of the following methods. Voice calls We welcome your calls at 1(866) 872-2538 (VPACKET) Monday through Friday, from 9:00 am to 6:00 pm Pacific Time. Voice mail is available during non-business hours. E-mail If you prefer, you can send information requests to our e-mail address: info@vpacket.
Contents Chapter 1 About the web interface 1 Node menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS Configuring dynamic host control protocol (DHCP) settings . . . . . . . . . . . . . . . . . . . . . . 44 Enabling and disabling network address translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Defining network timing protocol settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Configuring routing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Enabling routing information protocol . . . . .
About the web interface 1 Contents Overview, page 3 Accessing the Web Interface for the first time, page 7 Launching the Web Interface, page 8
CHAPTER 1 About the web interface 2 Vpacket 5100/6100 Series Web Interface Manual
Node menu Overview The Web Management Interface provides a comprehensive suite of functions (configuration management, fault monitoring, diagnostics, and performance monitoring) for managing Vpacket edge network systems in converged broadband networks. It allows management of the 6100 VDR using a Web browser. The Web management interface provides an alternative method for device management compared to the SNMP-based Vpacket Network Management System (VNMS) and CLI (console and telnet).
CHAPTER 1 About the web interface Alarm menu The alarm menu is for managing system alarms. The alarm options are: • display (lists the latest system events in the VDR) • control (controls sending SNMP traps from the VDR to external destinations) Settings menu The settings menu allows you to display and set the VDR configuration.
Monitor menu Monitor menu The monitor menu allows you to view the IP Routing Table information. The monitor option is ip route, which displays the IP Routing Table. Utility menu The utility menu allows you to access system-level tools.
CHAPTER 1 About the web interface • test control (a VQM feature that allows testing a specific destination number offline, in an accurate manner) • test result (a VQM feature that allows you to view the results of a voice quality test) Logout command The logout selection is a command that terminates the current session and returns you to the logon screen. You must confirm this action (Figure 1-1). Figure 1-1.
Accessing the Web Interface for the first time Accessing the Web Interface for the first time To access the web interface for the first time, first you need to connect the VDR to a LAN (See “Chapter 3 Port connections” in the Vpacket 5100/6100 Series Installer’s Guide for details). After making the physical connections, you can follow these steps. To launch the web interface for the first time 1. Open a web browser of your choice. Figure 1-2. Browser window 2.
CHAPTER 1 About the web interface Launching the Web Interface You can launch the Web Management Interface, which is directly embedded in the 6100 VDR, by following these steps. Figure 1-4 shows the Web Management Interface logon window. To launch the Web interface 1. Launch your Web browser. 2. Point your browser to the IP address of the VDR by entering HTTP://. (for example, 192.168.0.254 or your WAN IP address) 3. When the login window appears, enter your login name and then Tab.
Node options 2 Contents Overview, page 11 Viewing the System Status window, page 12 Importing files, page 13 Exporting files, page 15 Saving recent changes, page 16 Rebooting, page 16
CHAPTER 2 Node options 10 Vpacket 5100/6100 Series Web Interface Manual
Overview The node menu is for viewing and managing the configuration of the 6100 VDR.
CHAPTER 2 Node options Viewing the System Status window When you load the Web Management Interface, the System Status Window is the first screen that you see. This window lists all the currently configured system-level attributes for the 6100 VDR. Figure 2-1.
Importing files Importing files From the Import Files window you can instruct the 6100 VDR to download system files–where Image denotes software code and Configuration is a configuration file–from an external FTP Server. The parameters in this window include: • File Type lets you choose between configuration and image (software binary). • File Name is where you specify the case (case-sensitive).
CHAPTER 2 Node options The FTP Server Information must be accurately filled in and may appear already completed if you previously used the set ftp commands from the CLI. Note. The file names you enter must be exact because the software is case-sensitive. Figure 2-2. Import File window To import a file 1. Enter the file name, select the correct file type, and select the slot in which it resides. 2. Verify the values in the FTP Server Information fields. 3. Click Submit.
Exporting files Exporting files From the Export Files window, you can instruct the unit to upload system files by name and type (bin for executable code and config for a configuration file) to an external FTP Server. Figure 2-3. Export File window To export a file 1. Input the file name and select the correct file type. 2. Verify the FTP server information. 3. Click Submit.
CHAPTER 2 Node options Saving recent changes From the Save Settings window you can save recent changes to the VDR configuration file (MAIN.CFG) or create a backup configuration file. These files can be exported to an external FTP server for configuration backup. Figure 2-4. Save Settings window To save changes to the configuration file 1. Select Save Settings. 2. Verify that the Save radio button is enabled and the name main.cfg is in the file name field. 3. Click Submit.
Rebooting Note. You must confirm this action. See Figure 2-5. • the VDR is forced to reboot • all statistical counters are reset Before rebooting, the 6100 VDR will ask you to confirm that you want to reboot the system (Figure 2-5). Figure 2-5.
CHAPTER 2 Node options 18 Vpacket 5100/6100 Series Web Interface Manual
Alarm options 3 Contents Overview, page 21 Viewing alarms, page 21 Configuring alarms, page 23
CHAPTER 3 Alarm options 20 Vpacket 5100/6100 Series Web Interface Manual
Viewing alarms Overview The alarm menu is for managing system alarms. The alarm options are: • display lists the latest system events in the VDR • control controls sending SNMP traps from the VDR to external destinations Viewing alarms This window allows you to view captured alarms. The alarms, as reflected in the tables, remain in the tables until the VDR is reset. Once reset, the original severity thresholds are displayed. Figure 3-1.
CHAPTER 3 Alarm options • Processing error • Performance • Threshold-Crossing alarm • Security • Debug • Severity, which can include any of the following: • Cleared • Warning • Minor • Major • Critical • Cause, which can include any of the following: • Other • Security Alarm Causes • Invalid Access • Time: Date (YYYY:MM:DD) and time (HH:MM:SS) in 24-hour format.
Configuring alarms Configuring alarms You can configure the VDR to send SNMP traps to external destinations from this window. Figure 3-2 shows an empty SNMP Trap table. Figure 3-2. Alarm Control-SNMP Trap window To create SNMP trap destinations 1. Click on alarms. 2. From the Alarm Control window, click Add. 3.
CHAPTER 3 Alarm options Figure 3-3. Alarm Control-SNMP Trap Add window 4. When you click Submit, the Alarm Control-SNMP Trap Add window reappears, now with the new SNMP trap destination listed in a table (see Figure 3-4). Figure 3-4.
Configuring alarms To edit SNMP alarm controls 1. Select the Edit button belonging to the trap destination you want to edit from the right-hand column listed in the Alarm Control-SNMP Trap window (Figure 3-5). 2. When the Alarm Control-Edit Trap window opens, enter the new the UDP port number. 3. Click Submit. Figure 3-5. Alarm Control-Edit window To delete SNMP alarm controls 1.
CHAPTER 3 Alarm options 26 Vpacket 5100/6100 Series Web Interface Manual
Settings options 4 Contents Overview, page 29 Configuring and viewing WAN settings, page 30 Entering and viewing system settings, page 33 Setting voice services, page 34 Configuring dynamic host control protocol (DHCP) settings, page 44 Enabling and disabling network address translation, page 52 Defining network timing protocol settings, page 56 Configuring routing information, page 58 Enabling routing information protocol, page 60
CHAPTER 4 Settings options 28 Vpacket 5100/6100 Series Web Interface Manual
Overview The settings menu allows you to display and set the VDR configuration.
CHAPTER 4 Settings options Configuring and viewing WAN settings This window displays the WAN interface configuration parameters that correspond to the WAN interface module within the 6100 VDR. Figure 4-1. WAN Setting window To specify the values of a T1 WAN interface 1. Click settings. 2.
Configuring and viewing WAN settings 3. Click Submit to accept changes or click wan to return to the WAN Settings window. Figure 4-2.
CHAPTER 4 Settings options To view the WAN setting information table Select “T1 configuration” from the Select T1 configuration pull-down menu (Figure 4-3). Figure 4-3. WAN Setting T1 configuration window Configuring and viewing LAN settings The LAN Settings window allows you to specify the IP address and subnet mask for the LAN interface(Figure 4-4). Figure 4-4.
Entering and viewing system settings To delete a LAN configuration Click on delete to delete the LAN configuration. To configure the LAN 1. From the LAN Settings window, click Add. 2. Enter the IP address, subnet mask, and whether the interface is NATed or NotNATed. 3. Click Submit to accept the changes or Return to LAN settings to disregard these changes. Figure 4-5.
CHAPTER 4 Settings options The System Name that you enter becomes the prompt for the Command Line Interface (CLI). Figure 4-6. System Settings window To specify the system information for a VDR 1. Click settings and then system. The System Settings window appears (Figure 4-6). 2. Enter the appropriate information. 3. Click Submit. Setting voice services You can configure parameters for voice services from the Voice Settings window.
Setting voice services In an MGCP environment, you can perform these MGCP-specific actions: • “Adding, editing, or deleting a media gateway controller” on page 40 • “Editing the MGCP end point” on page 42 • “Viewing and editing the media gateway control protocol parameters” on page 43 Figure 4-7 shows the whole window and Figure 4-8 shows the “Select Telephony Configuration:” dropdown menu. Figure 4-7. Voice Settings window (MGCP choices shown) Figure 4-8.
CHAPTER 4 Settings options Viewing and editing telephony channel identifiers You can view and modify the parameters of the telephony channels (identified by integers called Telephony Channel Identifiers or TCIDs) from the Telephony Channels window. To view TCIDs, click settings and then voice. Figure 4-9. Telephony Channels window Each of the telephony channels can be defined using these parameters: 36 • Channel Unique number assigned as the TCID value.
Setting voice services • MaxCallDuration Specifies the allowable length of the call. Range: 65535–infinity. • Tone Generation Specifies the tone type according to national standards. Choices are: us (United States), japan (Japan), and uk (United Kingdom). Editing a TCID You can edit a TCID by following these steps. To edit a TCID 1. Click settings and then voice. 2. Select Telephony Channel from the “Select Telephony Configuration:” dropdown menu. The Telephony Channels window should appear. 3.
CHAPTER 4 Settings options Viewing, editing, or deleting a codec You can view, edit, or delete one of the available codecs supplied with the 6100 VDR from the Codec Profile window. To view a codec 1. Click settings and then voice. 2. Select Codec Profile from the “Select Telephony Configuration:” dropdown menu (Figure 411). Figure 4-11.
Setting voice services • Echo Canceller Tail Length Enables: disables the echo cancelling services (the maximum delay in milliseconds between the issuing of a master signal and receiving the resulting echo) • Voice Activity Detector Enables: disables the Voice Activity Detector (VAD) which monitors the passage of voice traffic onto the network • Voice Activity Detector Threshold Range: 0–10 with an Adaptive option • Silence Detect Time: Sets the duration for declaring silence detection (using VAD) f
CHAPTER 4 Settings options 5. Click submit to accept the changes or Return to Codec Table link to disregard the changes and return to the previous window. Figure 4-12. Codec-Edit window To delete a codec 1. Click settings and then voice. 2. Select Codec Profile from the “Select Telephony Configuration:” dropdown menu. 3. Click delete in the far-left column beside the listing you want to delete. 4. Click submit to accept the delete action or Return to Codec Table link to disregard the changes.
Setting voice services Figure 4-13. MGCP Address Configuration window To edit media gateway controller information 1. Click settings and then voice. 2. Select MGCP Address Configuration from the “Select Telephony Configuration:” dropdown menu in the Voice Settings window. 3. Click edit. The MGCP Address Configuration-Add window appears (Figure 4-13). Figure 4-14. MGCP Address Configuration-Add window 4. Make changes as appropriate. 5.
CHAPTER 4 Settings options Editing the MGCP end point From this window you can set and view the current settings for the MGCP end points. Each telephony channel on the system is an MGCP end point. The configurable MGCP end point parameters include: • Index number A unique, sequentially numbered identifier for this terminal • Terminal Name A human-readable name.
Setting voice services To edit the MGCP end points 1. Click settings and then voice. 2. Select MGCP Terminal from the “Select Telephony Configuration:” dropdown menu on the Voice Settings window. 3. Click edit next to the entry that you want to change. The MGCP Terminal ConfigurationEdit window appears (Figure 4-16). 4. Enter changes as necessary. 5. Click submit to accept the changes or Return to Channel Configuration to ignore the changes and return to the previous window. Figure 4-16.
CHAPTER 4 Settings options • Maximum Delay Time Sets the maximum time delay before attempting to reconnect following a disconnect from the call agent. The default maximum time-out delay is 600 seconds. • Minimum Delay Time Sets the minimum time delay before attempting to reconnect following a disconnect from the call agent. The default minimum time delay is 15 seconds. Figure 4-17.
Configuring dynamic host control protocol Figure 4-18. DHCP Settings window Mode menu The Mode menu allows you to set the DHCP Server Status to Server or None (client). Whenever you select, you must click Submit to make your change effective. DHCP Configuration Options menu From this menu, you can view and set DHCP parameters for using either pool and static host functionality.
CHAPTER 4 Settings options DHCP pools Setting up a pool provides dynamic allocation of IP addresses from a specified address range. The static host configuration provides manual allocation of IP addresses for a specific host. Figure 4-19.
Configuring dynamic host control protocol • IP Range (Max) mandatory value, which sets the maximum (highest) IP address • Default Lease (Days) Sets a Default Lease (time-out value) in 0–365 days • Default Lease (Hours) Sets a Default Lease (time-out value) in 0–23 for hours • Default Lease (Mins) Sets a Default Lease (time-out value) 0–59 for minutes • Checkbox for selecting No Time Limit for Default Lease • Max Lease (Days) Sets a Default Lease (time-out value) in 0–365 days • Max Lease (Hour
CHAPTER 4 Settings options 3. Click Add. The DHCP-Add window appears (Figure 4-21). Figure 4-21. DHCP Pool-Add window 4. Fill in the appropriate fields. 5. Click Submit to add the new DHCP pool or click Return to DHCP Pool Table to disregard changes. DHCP Static Hosts When you select the DHCP Static Host option, you can view these parameters: 48 • Index A unique identifying number. • Host Name An ASCII name of up to 127 characters. • Hardware Address A MAC address of the host.
Configuring dynamic host control protocol • Mask The subnet mask for the network address. • Configuration File The name of an ASCII text file containing the current configuration. • Server The IP address of the specific network host which can be assigned. • DNS Servers 1 to 8 Sets the IP addresses of up to eight machines as DNS servers. You can follow these steps to add a DHCP static host. To add a DHCP static host 6. Click settings and then dhcp. 7.
CHAPTER 4 Settings options 10. Click Submit to accept the new information or click Return to DHCP Pool Table to disregard changes and return to the previous window. Figure 4-23. DHCP Static Host-Add window DHCP Status Options menu This selection allows you to view lease information and server status. Figure 4-24.
Configuring dynamic host control protocol DHCP Lease Information Option This is a read-only screen which displays all existing IP address leases as provided by the DHCP server. Figure 4-25. DHCP Server Lease option window DHCP Server Information Option This is a read-only screen which describes a simple text description of the DHCP server status. Figure 4-26.
CHAPTER 4 Settings options Enabling and disabling network address translation The network address translation (NAT) protocol is enabled during the initialization process if a valid WAN IP address is set. Otherwise NAT is disabled. NAT allows the WAN IP address to accept an appended port number on outgoing packets. This window allows you to enable or disable the NAT settings. To enable or disable NAT 1. Click settings and then nat. 2. Select the Enable or Disable radio button. 3.
Enabling and disabling network address To add a NAT IP port map 1. From the NAT Settings window, click the add button. Figure 4-28. NAT IP Port Mapping window 2. From the NAT IP Port Mapping window, select the protocol to be used. Choice are TCP or UDP. 3. Enter the outside port number. 4. Enter the inside IP address. 5. Enter the outside port number. Port number 65535 is the largest valid port number.
CHAPTER 4 Settings options 6. Click Submit or the Return to NAT Port Mapping link to return to disregard changes and return to the previous window. To add a NAT static IP mapping 1. Click settings and then nat. Figure 4-29. NAT Settings window 2. From the NAT Settings window, select the Static IP Mapping option from the left-hand side pull-down menu. The NAT Static IP Mapping window appears (Figure 4-31). Figure 4-30.
Enabling and disabling network address 3. Click Add (Figure 4-31). Figure 4-31. NAT Static IP Mapping-Add window 4. Enter the inside and outside IP addresses. 5. Click Submit to accept changes or the Return to NAT Static IP Mapping link to disregard the addition and return to the previous window. To set an application port 1. Click settings and then nat (Figure 4-32). Figure 4-32.
CHAPTER 4 Settings options 2. From the NAT Settings window, select the application option Port Setting from the pulldown menu on the right lower corner of the window. Figure 4-33. Application Port Settings window 3. Enter the desired port numbers. Well-known ports appear in the individual application fields. 4. Click Submit to accept changes or click nat to disregard changes and return to the NAT Settings window.
Defining network timing protocol settings • Interval for resynchronization Sets an interval in hours for validation of the time within a range of 1–255 hours with a default of 24 (Figure 4-34). Figure 4-34. NTP Settings window To define network time keeping 1. Click settings and then ntp. 2. Enter the NTP Server IP address, the time zone and the resynchronization interval. 3. Click Submit.
CHAPTER 4 Settings options Configuring routing information This window shows the RIP information for the VDR. The VDR supports RIP Version 1.0 in a silent listener mode, which allows the VDR to build a routing table that can be updated and ageout routing variables supplied to it. Figure 4-35.
Configuring routing information To add a static IP route 1. Click settings and then route. The IP Routing Table Setting window appears (Figure 4-36). Figure 4-36. IP Routing Table Setting window 2. Click the button Add Static Entry. The Static IP Route-Add window appears. Figure 4-37.
CHAPTER 4 Settings options 3. Add the following information in the form fields: • IP address • Mask • Next hop 4. Click Submit to accept the changes or click Return to IP Routing Table link to disregard the changes and return to the previous window. Enabling routing information protocol You can enable or disable the RIP function from this window. Figure 4-38. RIP Settings window To enable or disable RIP functions 1. Click settings and then rip. 2.
Monitor options 5 Contents Overview, page 63
CHAPTER 5 Monitor options 62 Vpacket 5100/6100 Series Web Interface Manual
Overview Overview From the Monitor window, you can view the IP Routing Table values (Figure 5-1). Figure 5-1. IP Routing Table window Each entry is assigned a sequential entry number.
CHAPTER 5 Monitor options 64 Vpacket 5100/6100 Series Web Interface Manual
Measuring VQoS 6 Contents Overview, page 67 Enabling the voice call monitoring, page 67 Viewing QoS results, page 68 Testing voice quality from a specific 6100 VDR, page 70 Viewing voice QoS (VQM) test results, page 71
CHAPTER 6 Measuring VQoS 66 Vpacket 5100/6100 Series Web Interface Manual
Enabling the voice call monitoring Overview The Voice QoS menu provides tools for monitoring Voice QoS from the VDR.
CHAPTER 6 Measuring VQoS 3. Click OK when the system returns the message: Voice QOS monitor enabled (Figure 6-2). Figure 6-2. Voice QoS monitor enabled message Viewing QoS results You can view the Monitor Results Table, which is part of VQS and contains the following details: 68 • Call Session A unique reference number of call sessions terminated in this VDR. • TelePort ID The telephony interface port ID which terminates the call session.
Viewing QoS results To view Voice QoS results 1. Click voice QOS and then click monitor results. A new window appears (Figure 6-3). Figure 6-3. Voice QoS Monitor Results window 2. To further evaluate the QoS of one of the displayed sessions, select detail. Figure 6-4.
CHAPTER 6 Measuring VQoS This window is divided into three informational (read-only) panels: • The Call Session lists information specific to this call, captured from the previous VOICE QOS MONITOR RESULTS Window, adding the Round Trip Delay value. • Near End Displays the Voice QoS data for the near-end termination of the call session. The Voice QoS score rates the quality of the call similar to the Mean Opinion Score (MOS) with 5 representing the highest quality and 1 the lowest.
Viewing voice QoS (VQM) test results 4. Click Ok to acknowledge the test in progress message (Figure 6-6) or click Cancel to stop the test. You will need to wait approximately 20 seconds before attempting to view the results. Figure 6-6. Test in progress message Viewing voice QoS (VQM) test results You can follow these steps to view your test results. To view test control results To view test results, click voice QOS and then click test result.
CHAPTER 6 Measuring VQoS 72 Vpacket 5100/6100 Series Web Interface Manual
Web utilities 7 Contents Overview, page 75 Administering users, page 75 Using access control lists, page 78
CHAPTER 7 Web utilities 74 Vpacket 5100/6100 Series Web Interface Manual
Administering users Overview From the Utility window, you can access the User Management features. At this time, the ping and the trace route options need to be accessed through the Command Line Interface. Through the Utility window, you can manage user accounts and set and maintain access control lists. Administering users You can add, delete, and edit users from the User Management window. To create a user 1. Click utility and then click user management (Figure 7-1). Figure 7-1.
CHAPTER 7 Web utilities 2. When the User Management window opens, click Add. Figure 7-2. User Management-Add window 3. Enter the user name, password and password confirmation. Note. Access privilege must be configured from the CLI. 4. Click Submit.
Administering users To edit a user profile 1. Click utility and select user management. 2. Click edit in the far-left column next to the entry that you want to change. Figure 7-3. User Management-Edit window 3. When the User Management-Edit window appears (Figure 7-3), you can change the user name and password. 4. Click the Submit button to save changes. To delete Users 1. Click utility and then click user management. Note. There is no confirmation message–if you click Delete, that user is gone. 2.
CHAPTER 7 Web utilities Using access control lists You can view access control lists by clicking utility and then acl. Figure 7-4. Access List entry window The Access List table lists access control list entries and includes: • the IP address for each entry • the subnet mask of each entry • the destination port • the valid protocol From the Access List window you can add or delete an entry from the table. To add an access control list 1. Click add from the Access List window. 2.
Using access control lists 5. Click Submit to create the entry or the Return to Access List link to disregard changes and return to the previous window. Figure 7-5. Access List-Add window To delete an access control list To delete an access control list entry from the Access List table, click delete next to the entry you want to remove from the table. Once removed, you cannot recover the access control list. You will have to create the list again.
CHAPTER 7 Web utilities 80 Vpacket 5100/6100 Series Web Interface Manual
Index A S audience iii syntax command iv B bold type iv C cautions iv chapter summaries iii command syntax iv contact information vi courier typeface iv customer care contact information vi D documentation, related v H HTTP see WEB interface 13 system status 12 L login, HTTP 7 M media gateway control (MGC) 40 media gateway control (MGC) server 40 N Network Timing Protocol configuring NTP 56 Network Timing Protocol (NTP) 56 notes iv T tasks configuring access control lists 78 configuring alarms 23
INDEX W warnings iv WEB interface alarm menu, description 4, 21 help menu, description 6 monitor menu, description 5 node menu, description 3, 11 settings menu 4, 29 utility menu, description 5 voice QoS menu, description 5 Web Management Interface, description 3 Index-2 Vpacket 5100/6100 Series Web Interface Manual
