VOX622 Bluetooth stereo headset User’s manual
Contents Brief introduction…………...…………………………..…....1 Before use……………………………………………………..1 1. Overview…………………………………………………...……1 2. Charging for headset..……………………………………………2 Getting started……..…………………………………………3 1. Turning on/off the headset…………....……………………......3 2. Wearing the headset.......................................................................3 3. Pairing/connecting…….……..............................……………..….4 1) Pairing headset with Bluetooth cell phone via Bluetooth……..….
Welcome to use this Bluetooth stereo headset, VOX622. Please read this user’s manual carefully before use. Brief introduction VOX622 is an In-ear Bluetooth stereo headset. Mini and portable design for easy taking. You can use it to enjoy wireless music and make a call at the same time. Besides, VOX622 support NFC technology for close pairing and connecting. Before use 1.
2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits prompt tones every 5 minutes and the red LED flashes. Please recharge the battery of the headset. The way of charging as following: Using USB cable 1. Turn on the cover of charging jack, and plug the USB charging cable 2.
Getting started 1. Turning on/off the headset Functions Operation Prompt tone Turning on Press and hold about 4 Four raise tone seconds until blue LED flashes Turning off Press and hold about 4 Four fall tone seconds until red LED flashes Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 2. Wearing the headset a.
b. Choose the suitable size eartips according to your ear and wear as following shown: c. Set up the cord management clips to get better wearing as following shown: 3. Pairing/connecting 1) Pairing headset with Bluetooth cell phone via Bluetooth Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone user’s manual for further information.
3) Activate your cell phone’s Bluetooth function and search for Bluetooth devices within range, select “Voxmio Freebird Pro” from the list of devices shown (enter password “0000 ” if the headset prompt); 4) After successful connecting, blue LED of headset flashes twice every 4 seconds Remarks: Pairing mode will last 2 minutes, the headset will back to standby mode if the pairing failure. If the pairing is not successful, turn off the headset and repeat the steps as above.
Remarks: Please keep the NFC area of cell phone and headset within 1 centimeter until the red and blue LED of headset flash alternately(First pairing time maybe 3 seconds). The headset will disconnect when the NFC area of cell phone and headset touch each other again. 3) Pairing headset with multi devices via Bluetooth The headset can connect with two Bluetooth cell phones at the same time.
Reject a call Incoming ringing End a call During a call Volume up During a call Volume down During a call Transfer conversation to mobile phone Transfer conversation to headset Microphone mute Cancel mute During a call call Long press about 2 seconds and release it until listen a tone Short press once Short press + button Short press — button Long press about 2 seconds One tone short One tone short During a call Long press about 2 seconds One tone short During a call Long press “+” abou
Note: Not all the mobile phones support all the functions listed above. Different function and prompt tone according to different mobile phone. Please refer to your mobile phone user’s manual. When the volume is adjusted to max or min, you will hear one prompt tone. When the headset under microphone mute mode, you will hear two tone continuously every 10 seconds. When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone.
3) Connect with two cell phones Functions Status of headset During phone call #1, End phone call #1 phone 2 has incoming and answer phone call call #2 During phone call #1, Retain phone call #1 phone 2 has incoming and answer phone call call #2 Switch call During call, one of phone call is retained During call, one of End current call, phone call is retained back to retain phone call 5.
6. LED indicator LED indicator Red and blue LED flashes alternately Blue LED flashes once every 2 seconds Blue LED flashes twice every 4 seconds Red LED flashes instead of blue LED Status of headset Pairing mode Not connected to device Connected to device Low battery 7. Factory Reset In the status of charging, long press “+” button about 4 seconds and release it until the red and blue LED flashes simultaneously, you will hear 4 prompt tone.
Don’t scratch the surface with sharp things. Don’t use this product during strenuous exercise. It may get damaged by sweat. In case the product doesn’t function properly, send it to the store you bought it. The staff will help you to solve the problem FAQs 1.What does it mean when red LED flashes instead of blue LED? Battery is low power, need to be recharged. 2.Why is the red LED off when charging? a) Please make sure the charging device connect with headset Well; b) The battery may dry up.
7. Why the pause/play, last/next song not function when playing music? Make sure your Bluetooth device supports AVRCP (Audio/Video Remote Control profile) Specifications Bluetooth version Bluetooth profiles Operating distance Headset music time Headset talk time Standby time Headset charging time Dimension Weight Bluetooth V4.0 Headset, Hands free, A2DP, AVRCP 10meters About 5 hours About 5.5 hours About 200 hours About 2 hours Headset: 37x16.3x27.7 mm Cable: about 500mm About 13 g Notes: 1.
