KVM08KD KVM Switch with Keyboard Mouse Build In
COPYRIGHT © This document is a copyright of the original manufacturer, 2000. The original manufacturer reserves the right to make improvements to the product(s) described in this manual at any time without notice. This manual may not, in whole or in part, be photocopied, reproduced, transcribed, translated, or transmitted in whatever form without the written consent of the manufacturer, except for copies retained by the purchaser for backup purposes. All rights are reserved.
TABLE OF CONTENTS CHAPTER 1 1.1 1.2 1.2 INTRODUCTION SPECIFICATION DIMENSION PACKING CHECK LIST 1 2 3 4 CHAPTER 2 2.1 2.2 2.
CHAPTER 1. INTRODUCTION The KVM08KD gives you the ultimate in cont rol of 8 PCs from one keyboard, mouse and monitor. To expand control ability the DB-25 Daisy-Chain allows with extra 15 KVM08 stack up for control 128 PCs from one keyboard, mouse and monitor. OSD (On-Screen Display) menu provides human friendly interface for naming each PCs and selecting one of them.
INTRODUCTION 1.
INTRODUCTION 1.2 DIMENSION 531.80 508.00 440.00 437 48.00 486.
INTRODUCTION 1.3 PACKING CHECK LIST Before you begin to install your KVM 08KD, please make sure that you received the following materials as listed below: Item KVM08KD Power adapter Power cord Mouse driver User’s Manual Qty 1 pcs. 1 pcs. 1 pcs. 1 pcs. 1 pcs. Remark KVM Switch with keyboard, mouse 48W, universal AC input AC inlet power cable 3.
CHAPTER 2. INSTALLATION 2.1 PRODUCT DETAIL Top View Current Active Port Displays Rear View PC port connectors Rear View VGA DC+12V/4.
INSTALLATION 2.2 HARDWARE INSTALLATION WARNING! Before attempting to connect anything to the KVM08KD or the computers, make sure everything is powered off. Otherwise, plugging and unplugging cables may cause irreversible damage to your computers and the KVM08KD. Step 1 1. How to slide KVM08KD back to rack Press two sides in front part of sliders and push KVM08KD back at the same time.
INSTALLATION Step 2 Connect the first computer’s VGA cable to the KVM 08KD. Using the VGA cable connect the male end of the cable to the VGA port on the computer, and the female end on the PC1 VGA port at the back of KVM08KD. Back of PC VGA DC+12V/4.0A Master Input PC2 PC4 PC6 PC8 PC1 PC3 PC5 PC7 Step 3 Connect the first computer’s PS/2 mouse and PS/2 keyboard ports to the KVM08KD.
INSTALLATION Step 7 You can now power up all your computers simultaneously. The first computer will show up on the monitor. Check to see if the keyboard, mouse and monitor work. If this is okay, press the “Select” button and check the functionality of the other computers. If you find any errors, double-check all of the cable connections. NOTES: 1.
INSTALLATION 3. SINGLE UNIT OR DAISY-CHAIN OPERATION KVM08KD has the capability to be Daisy-Chained with 15 more KVM08 units (for a total of 16), giving the user control over a maximum of 128 computers. Each KVM 08KD or KVM 08 unit is defined as a “BANK”. See the following diagram for more information. BANK numbers range from 0 to F (Hexadecimal), for a total of 16 banks. BANK 0 is the MASTER bank while BANK 1 through F are SLAVE banks.
CHAPTER 3. OPERATION Selecting which computer to operate can be done either by On-Screen Display, the select button, or through keyboard “Hot Key” commands. You will notice that after the KVM08KD switches to another computer, the mouse will be inoperative for about 1-2 seconds. This is normal operation and ensures that proper mouse synchronization is established. Pressing the “Select” button cycles you through all the ports, including inactive ports.
AutoScan Mode SCROLL LOCK SCROLL LOCK Enable AutoScan mode 0 In AutoScan mode, KVM 08KD remains on one channel for a number of seconds, before switching to the next. This time interval is set in the On-Screen Display menu. NOTE: There is no mouse or keyboard control in this mode. This is necessary to prevent errors.
˙You can navigate through the active ports by using the arrow keys. The OSD menu will only allow you to move to active ports. NOTE: If a computer is connected and is powered up, but the OSD menu does not display a “®”, you will have to RESET the KVM 08KD to re-detected the powered computers. This is done by simultaneously pressing the AUTO and SELECT buttons on the front panel. ˙Pressing the INSERT key allows you to rename the port. Press ENTER to complete.
When requesting RMA service, please fill out this “RMA Service Request Form”. Without this form your RMA will be REJECTED!!! RMA No: Company: Phone No. Fax No.: Return Shipping Address: Shipping by: □Air Freight Item Model Name Item Problem Code *Problem Code: 01:D.O.A. 02: Second Time R.M.A.
