PRODUCT MANUAL 1
SPITFire HD GEN II ™ Specifications SPITFIRE HD GEN II PRISM SCOPE ™ MAGNIFICATION 3x MOUNT TYPE Low Mount (27mm) OBJECTIVE LENS DIAMETER RETICLE COLOR EYE RELIEF 5x Lower 1/3 Co-Witness (40mm) 21mm 25mm Red Red 2.6" (67mm) 2.7" (68.6mm) 37.9' @ 100 yds. 23.3' @ 100 yds. ADJUSTMENT GRADUATION 1 MOA 1 MOA TRAVEL PER ROTATION 42 MOA 42 MOA MAX ELEVATION ADJUSTMENT 250 MOA 200 MOA MAX WINDAGE ADJUSTMENT 250 MOA 200 MOA PARALLAX SETTING 100 yds. 100 yds. 3.0" (76mm) 3.
SPITFire HD GEN II ™ CONTROLS AND ADJUSTMENTS Battery Installation Remove the battery compartment cover using the included tool or a coin. Install and orient the CR2032 battery so the positive (+) side faces out, then replace the cover. When replacing the cover, be sure it is fully screwed down with the o-ring seal in place. Illumination Adjustments The Spitfire™ HD Gen II sight offers 12 brightness settings, the lowest two settings being ultra-low for use with night-vision equipment.
SPITFire HD GEN II ™ AR-BDC4 Reticle Subtensions To adjust the reticle focus: 1. After mounting the sight, point the sight at a blank white wall or up at the sky. 2. Starting with the fast-focus eyepiece all the way in, glance through the optic. If the reticle is not in focus, rotate the eyepiece out counter clockwise slightly, and look through the optic again. 3. Repeat this process until the reticle is in sharp focus.
SPITFire HD GEN II ™ STANDARD BULLET DROP FOR 5.56MM / .223 LOADS 5.56mm/.223 55 gr, FMJBT, 3050 FPS muzzle velocity. Main crosshair zeroed at 50 yds (220 yds). CONTROLS AND ADJUSTMENTS Windage and Elevation Adjustments To get the best results, proper mounting is essential. Although not difficult, the correct steps must be followed. Your firearm will need to be equipped with a Picatinny® or Weaver® style rail/base. If needed, these may be purchased at most firearms dealers.
SPITFire HD GEN II ™ Mount Height Options The Spitfire HD Gen II prism sight can be mounted at two heights, lower 1/3 co-witness or a “low” mount option. To mount at lower 1/3, mount the sight as received. The optic center will be 40mm above the base surface. To mount for “low” height, remove the lower 1/3 co-witness mount and replace it with the low mount. The optic center will be 27mm above the base surface. ™ To change the mount height, loosen and remove the four base screws and remove the base clamp.
SPITFire HD GEN II ™ Final Range Sight-In Final sight-in should be done at the range using the exact ammunition you expect to hunt or shoot with. We recommend using a 50 yard zero for best results with the AR-BDC4 reticle. 1. After the Spitfire™ HD Gen II has been bore sighted, fire a shot or two at your desired zero distance to check that you’re roughly on target. If necessary, adjust the dot to put you near the target’s center (see Windage and Elevation Adjustment on page 8). 2.
SPITFire HD GEN II ™ TROUBLESHOOTING Please check the following before returning a scope for service: If the reticle does not illuminate: • Is the battery dead? Replace. • Is the battery installed correctly? Be sure the battery is oriented with positive side facing outward. • Is the battery cover loose? Be sure cover is snug and contact points are clean. VIP WARRANTY OUR UNCONDITIONAL PROMISE TO YOU. We promise to repair or replace the product. Absolutely free.
M-00289-1 © 2021 Vortex Optics ® Registered Trademark and TM Trademark of Vortex Optics.
