VOPTech GoIP User Manual GoIP Series GSM VoIP Gateway User Manual V3.0 Voptel Technology Co., Ltd Http://www.voptech.com sales@ voptech.com support@ voptech.com 2010-11-17 Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual Content Content.......................................................................................... 1 1 Overview .................................................................................... 4 1.1 Introduction.........................................................................................................................4 1.2 Protocols .............................................................................................................................
VOPTech GoIP User Manual 3.4.3 Main DNS ..............................................................................................................28 3.4.4 Secondary DNS......................................................................................................28 3.5 Call Setting........................................................................................................................29 3.5.1 H.323 Terminal Setting .................................................................
VOPTech GoIP User Manual 5 Factory Default Parameter Table............................................ 74 Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual 1 Overview 1.1 Introduction The GoIP series gateway is a broadband relay gateway newly developed by VOPTEL Technology. It is a new product for seamless connection between the GSM network and VoIP network. When the mobile phone SIM card is installed in the GoIP, users can register the GSM phone to the VoIP softswitch system. Through the GoIP, users can realize the uplink and downlink calls between the GSM network and the VoIP network.
VOPTech GoIP User Manual 1.2 Protocols 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 TCP/IP V4 (IP V6 automatic adaptive) ITU-T H.323 V4 standard H.2250 V4 standard H.245 V7 standard H.235 standard (MD5, HMAC-SHA1) ITU-T G.711 Alaw/ULaw, G.729A, G.729AB, G.723.1 and GSM voice coding RFC1889 real-time digital transmission protocol Firewall penetration technology SIP V2.
VOPTech GoIP User Manual Embedded HTTP that accesses internal parameters PPPoE dialing NAT broadband routing function DHCP client DHCP server Software online upgrade Automatic calling Supporting multiple languages Supporting outgoing SMS calls 1.5 Product Package List 1). A GoIP gateway 2). 12V/2A DC(For GoIP_4) or 12V/3A DC (For GoIP_8) transformer 3). An Ethernet cable (2 m) 1.6 Product Appearance Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual 1) LAN The network input port that is connected to the router, Modem, and switch; 2) PC The network output port that is connected to network sharing equipment (less than 100 terminals) 3) 12V/2A DC (For GoIP_4) or 12V/3A DC (For GoIP_8) transformer The output terminal that connects the transformer equipped with delivery 4) Reset The reset switch for quick restart of the GoIP. Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual 2 Installation 2.1 Installation Procedure The GoIP has 1/8 SIM card slots, an LAN port, and a PC port. The installation procedure is as follows: 1. Open the bottom cover of the GoIP and insert an SIM card of the local GSM network; 2. Connect the LAN port with the upper-layer network equipment with the Ethernet cable; 3. PC port supports network sharing, so connect the PC port to the computer or lower-layer switch (HUB or router); 4.
VOPTech Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual 2.3 LED Indicators Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual The description of LED indicators is as follows. Description LED Power indicator This indicator is constantly ON after LAN indicator This indicator is ON after connected with the network equipment and blinks during data transmission. PC indicator This indicator is ON after connected with the network equipment and blinks during data transmission. RUN indicator connected with power. 1. The RUN indicator blinks once every 100ms during startup. 2.
VOPTech GoIP User Manual 2.4 SMS Instructions Users can send instructions to the GoIP gateway through the SMS. Function Obtain information from the LAN port Reset the setting 2) INFO or info GoIP RESET Password Reboot the GOIP gateway 1) Instructions (Short message content) REBOOT Password Remark Case insensitive The keyword RESET is case insensitive. The keyword REBOOT is case insensitive.
VOPTech GoIP User Manual number of the gateway and if connected dial *00 to obtain the IP address. B: The default IP address and mask of the PC port are 192.168.8.1 and 255.255.255.0 respectively. Enable the DHCP service of the PC port. Connect the computer with the PC port of the gateway through the IP address of the PC port, and set the IP of the computer to dynamic IP or fixed IP as 192.168.8.xxx and the default gateway as 192.168.8.1. Open the Internet Explorer and enter 192.168.8.1 or http://192.
VOPTech GoIP User Manual GoIP Status Interface GoIP_4 Status Interface Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual GoIP_8 Status Interface The GoIP gateway adopts the tree structure. The menu is on the left and the setting parameters are on the right, as shown in the above figure. You can also access the setting page of the GoIP through the IP address 192.168.2.216 or 192.168.2.172 of the LAN port of the gateway. The login method is the same as that of the PC port, but you must first obtain the IP address of the LAN port. 3.
VOPTech GoIP User Manual software, make sure the update version is newer than the current version. C. Hardware Version It displays the current hardware version of the gateway. D. Line Register Status It displays the login status of the line. When the line has logged into the SIP server or H.323 Gatekeeper, LOGIN is displayed, otherwise, LOGOUT is displayed. E. Line Use Status It displays the use status of the line. When the line is in use, the status is ACTIVE, when the line is idle, the status is IDLE.
VOPTech GoIP User Manual User Options of the GoIP User Options of the GoIP_4 / GoIP_8 3.3.1 Language To select a language, refresh the page to enter the language page required. For example, the current language is simplified Chinese. If you wish to display the page in English, click “English” in the menu. After your terminal is restarted, all the pages will be displayed in English. You can also use other languages for setting, as shown in the following figure. Voptel Technology Co.
VOPTech GoIP User Manual Click “English” on the upper right corner of the setting page. Then, the setting page will display all info in English. But the shortcut will not change the language of the setting page when logged in next time. 3.3.2 Time Zone and Time Server This item displays the adjusted time according to the selected time zone. The gateway receive time and date information from the server through the Network Time Protocol and the time difference will be automatically adjusted.
VOPTech GoIP User Manual automatic setting feature and enter the address of the server. If the service provider does not provide the automatic setting, you need to select “Disable” to speed up the startup time of the GoIP. It is a special server, which needs the support of the specific system. 3.3.5 Setting of the Remote Control Press *20# on the terminal to initiate the request to realize the remote management of equipment. The remote control server is provided by the service provider.
VOPTech GoIP User Manual administrator only needs to provide a GSM number to the user to call in the VoIP system. Each GoIP can operate in any of the following modes: Prohibit: This mode is used when the GoIP operates independently. Serve as the server: When GoIP operates in this mode, the administrator only needs to provide the user with a GSM number of the GoIP as a unique access number to the GoIP group. In one GoIP group, only one GoIP gateway can be used as the server.
VOPTech GoIP User Manual Serve as the client: When GoIP operates in this mode, it will send its real-time status to the server of the GoIP group, so that the GoIP server can deploy the call forwarding. Server address: It is the IP address of the GoIP gateway of the GoIP group server. GSM number: It is the telephone number of the GSM SIM card used by the GoIP. 3.3.6 Anonymity of the GSM Caller Number The caller number can be hidden, but this needs the support of the GSM operator. 3.3.
VOPTech GoIP User Manual 3.3.8 SMS Send to Client The SMS server sends the request to the mobile phone via the GoIP, or the mobile phone sends the request to the SMS Server via GoIP. SMS server address: This is for filling the IP of the SMS server. Please make sure that server is installed with the GoIP SMS management server software independently developed by VOPTEL Technology (The software can be downloaded from the VOPTEL website or obtained from our technical personnel).
VOPTech GoIP User Manual 3.3.7 GSM Band The GoIP gateway support the GSM/GPRS 900/1800 and 850/1900 bands. 3.3.8 Timing Restart The GoIP gateway restarts at least once at the specified time every day to clear the buffer of the GoIP, so that the GoIP can operate normally. 3.3.9 China Area Code Matching The GoIP can match all area codes of China to ensure the prompt dial. The default status is Disable. 3.3.10 IVR By default, the IVR is enabled.
VOPTech GoIP User Manual 3.3.11 Prompt Tone System The prompt tones are the combination of the intervals and frequencies of the dialing tones and ring-back tones when users hook off the telephone. You can select the following prompt tones for the GoIP according to the countries and regions where the GoIP is used, so as to remain conventional tones. Customize: Users can customize prompt tones according to their special requirements. Select Customize, the following setting parameters are displayed.
VOPTech rpt: GoIP User Manual the number of repeats (0 to infinity) c1on: the duration when the frequency 1 is on (ms) c1off: the duration when the frequency 1 is off (ms) c2on: the duration when the frequency 2 is on (ms) c2off: the duration when the frequency 2 is off (ms) c3on: the duration when the frequency 3 is on (ms) C3off: the duration when the frequency 3 is off (ms) f1: the frequency of tone #1, 300 to 3000Hz f2: the frequency of tone #2, 300 to 3000Hz f3: the frequency of to
VOPTech GoIP User Manual 3.4.1 LAN Port Setting The LAN port of the GoIP can be set to the dynamic IP through DHCP, fixed IP, and PPPoE dialing. There are three setting modes: A. Dynamic IP (DHCP) This setting is default. If the network for the user provides the DHCP service, the GoIP will require the network information such as IP address from the DHCP server automatically. B. Fixed IP Select fixed IP, and the following setting page is displayed.
VOPTech GoIP User Manual C. PPPOE PPPoE (Point-to-point protocol over Ethernet) is a network protocol that compresses the PPP in the Ethernet. Select PPPoE dialing, and enter the account and password provided by the network provider. D. 802.1q VLAN When the network serving the user provides the VLAN service, enter the parameter as required. E. Advance… Click Advance, and the Hardware address and Broadcast address are displayed in the page.
VOPTech GoIP User Manual Select the fixed IP, and the following setting parameters are displayed. Enter the IP address and subnet mask (the network section of the IP address should be different from that of the LAN port to prevent conflict). C. Enable the DHCP Service This service can be enabled only when the PC port of the GoIP is set as the fixed IP. To enable the DHCP service, you need to enter the start address and end address. E.
VOPTech GoIP User Manual null. 3.5 Call Setting This section describes the basic setting of the network connection relating to the GoIP gateway, which supports two protocols: H323 and SIP. The setting page is as follows: You can select a protocol in the “Terminal Type”. 3.5.1 H.323 Terminal Setting The H.323 protocol involves the direct connection mode and Gatekeeper mode. 3.5.1.1 Direct Connection Under this mode, the GoIP operates in the point-to-point status.
VOPTech GoIP User Manual C. H.323 ID H232 ID is used to verify the account. Users can set this parameter according to the requirements of the service provider. D. Default Voice Gateway This parameter is used to find the proper Gatekeeper or IP address of the equipment of the callee. Enter the IP address, such as 192.168.2.197, or domain name, such as gk.yourisp.com.
VOPTech GoIP User Manual A. H.323 Telephone Number The value of this parameter is a decimal numeral string that is used to confirm the telephone number in the telephony network. For example, 191 is a valid telephone number. Enter the telephone number in this parameter. B. Gateway Prefix When you register through the gateway prefix, enter the prefix number. When the prefix number is called, a dialing tone is heard and then the secondary dialing is required.
VOPTech GoIP User Manual G. Enable Authentication (Auth) Click “Enable Authentication” and enter the following parameters when you need to set the H.235 authentication code and password. 3.5.1.3 Advance Setting of the H.323 The advance option of the GoIP involves the signaling and media, corresponding to “Advance Setting” and “Media” respectively. Select “Advance Setting” under H323, and the following setting page is displayed: A.
VOPTech GoIP User Manual H.323 unites. The RAS port can be used to specify the UDP and used with the router port for mapping. B. Call Signaling Port (Q.931 Port) H.225-Q.931 is a call control protocol of the H.323 for transmitting the call setting and unloading information between two H.323 units. It is used to specify the Q.931 port (TCP) that receives calls and used with the router port for mapping. C. Media Control Port (H.245 Port) H.245 is the media control protocol of the H.323.
VOPTech GoIP User Manual 1). Inband DTMF The inband DTMF transmits dialing tones and call voices together, without any processing. Therefore, the inband DTMF transmits DTMF signals through a single way. 2). Outband DTMF The outband DTMF transmits dialing tones over protocols, such as RFC2833, which can ensure the validity of the transmission. G.
VOPTech GoIP User Manual A) Single server mode: Multiple VoIP channels can share the same setting. B) Line setting: Each VoIP channel can be served by different service providers or served by the same service provider. In the latter case, multiple different telephone numbers (accounts) can be registered on the same service, so that each telephone number is bound to the corresponding VoIP channel.
VOPTech GoIP User Manual The SIP registration server is a server used by the gateway to register the account. This parameter is used to set the IP address or domain name of the SIP login server. If the SIP registration server uses a special port (other than the SIP default port: 5060), you can add the detailed port number at the end of the IP address or domain name of the registration server. For example, 192.168.2.26:3000 or hy.con.com:3000.
VOPTech GoIP User Manual 3.5.2.3 Setting by Line ( Valid for the GoIP_4 and GoIP_8) GoIP_4 config by line Voptel Technology Co., Ltd All Rights Reserved.
VOPTech GoIP User Manual GoIP_8 config by line You need to set parameters for each line and the setting method is the same. The setting parameters are as follows: A) Telephone Number This parameter is used to set the telephone number of the line. The telephone number is an unique ID when the gateway serves as the callee. B) Gateway Prefix The gateway prefix enables the connection of calls through a particular line. It can match the first digit only. You can set a gateway prefix for multiple lines.
VOPTech GoIP User Manual This parameter is used to set the address of the SIP proxy server. If the SIP proxy server uses the special port (other than the SIP default port 5060), you can add the detailed port number at the end of the IP address or domain name of the proxy server. For example, 192.168.2.26:3000 or hy.con.com:3000. D) SIP Registration Server The SIP login server is a server that the gateway registers the account.
VOPTech GoIP User Manual This parameter is used for registration backup. When a backup registration server exists in the user’s system, the user can enable this parameter. When the backup server is enabled, the gateway will automatically log into the backup server in case of the failure of the main server. 3.5.2.4 Trunk Gateway Mode The trunk gateway is used to connect the VoIP network with the GSM network and convert the related protocols, so that users served by the two networks can call each other.
VOPTech GoIP User Manual SIP Trunk Gateway1. E) Registration Timeout (s) When the registration timeout is 0, you cannot register the gateway and the gateway will be connected to the server directly. You can reference the setting parameters of the single server mode to register the gateway. F) Authentication ID This parameter is used to set the authentication account when the gateway logs into the SIP Trunk Gateway1 proxy server. The parameter can be null in the case of interconnection.
VOPTech GoIP User Manual B. NAT Hold This parameter is used to hold the port that is activated by the NAT for SIP signaling communication. The unit of the parameter is m. C. Timeout Setting E. Signaling QoS Quality of Service (QoS) is a network’s capacity to provide priority services, including the special bandwidth, jitter control and delay (used for real-time and interactive traffic), and improvement of the packet loss ratio.
VOPTech GoIP User Manual 1) Inband DTMF The inband DTMF transmits dialing tones and call voices together, without any processing. Therefore, the inband DTMF transmits DTMF signals through a single way. 2) Outband DTMF The outband DTMF transmits dialing tones over protocols, such as RFC2833 and SIP INFO, which can ensure the validity of the transmission. G. Registration Mode When the registration information is sent to the platform under Mode 1, “experise” info is included.
VOPTech GoIP User Manual This parameter indicates the duration of sending a network packet. If this parameter is null, it indicates that the default value is 20ms. It is used to specify the size of the media packet. The unit is ms (the actual number of bytes depends on the compression algorithm). C. Jitter Delay Processing Mode This parameter is used to specify the algorithm model of the jitter delay buffer. The “Adaptive” mode should be set.
VOPTech GoIP User Manual 3.5.6 Firewall Penetration In the advance option of the call setting, the signaling and media have separate firewall setting, as shown in the following figures. 3.5.6.1 Traversal of H323 Signaling over NAT The traversal of H323 signaling over NAT (firewall) is classified into 4 categories: A. No The mechanism of firewall traversal is not supported. B. Nat Citron The Citron is a special firewall traversal protocol for GnuGK and used with GnuGK. C.
VOPTech GoIP User Manual The trunk agent protocol supports encryption on communications over the gateway. The H323 trunk agent protocol supports encryption on signaling in different modes (for details about the agent mode, see section 3.5.6.3 “Media NAT Traversal”). Note: This feature needs the support of the server developed by VOPTEL Technology. 3.5.6.2 Traversal of SIP Signaling over NAT The traversal of SIP signaling over NAT (firewall) is classified into: A.
VOPTech GoIP User Manual The trunk agent protocol supports encryption on communications over the gateway. This feature needs the support of the server developed by VOPTEL Technology. 3.5.6.3 Media NAT Traversal The media NAT (firewall) traversal is classified into four types: A. No firewall The firewall traversal mechanism is not supported. B. Port Transparency/DMZ The port transparency is used to transfer the network port on the LAN interface to the computer or the server in the LAN.
VOPTech GoIP User Manual Media agent mode: Mode 1: media encryption and agent (supported by all versions of relay servers). Mode 2: media encryption and agent, supporting the transit over the specified port (supported by V2 relay server). Mode 3: media encryption and agent for the conversion of RTP data to TCP packet, supporting the transit over the specified port (supported by the relay server later than V2). 3.5.7 Dialing Rule The GoIP supports number dialing by rules.
VOPTech GoIP User Manual 2. Rule: “00:-00|0"-0+86|:+86755” a. The input number is “008522343318” and the output number is “8522343318”. b. The input number is “02083185711” and the output number is “862083185711”. c. The input number is “83185700” and the output number is “8675583185700”. 3. Rule: “00:|0:-0+0086|:+0086755” a. The input number is “008522343318” and the output number is “008522343318”. b. The input number is “02083185711” and the output number is “00862083185711”. c.
VOPTech GoIP User Manual This rule enables the GoIP to add 0 before the mobile phone number and 0755 before the telephone number. The above rule can be change to: “0:|13[0-9]xxxxxxxx:+0|[1-8]xxxxxxx:+0755” Similarly, this rule enables the GoIP to add 0 before the mobile phone number and 0755 before the telephone number. However, the length of the mobile phone number is limited to 11 digits. As shown above, the length of telephone numbers is limited to eight digits.
VOPTech GoIP User Manual After the volume setting is completed, click “Save” and the setting will take effect immediately (for ongoing calls, the setting will not take effect immediately). Note: The adjustment on the output volume of the line may cause the terminal to fail in dialing numbers. Therefore, set this parameter carefully. The adjustment on the input/output volume is for VoIP lines. 3.
VOPTech Downlink: from VoIP to PSTN GoIP User Manual Uplink: from PSTN to VoIP Note: The value of Call PSTN must be Enable. Otherwise, The GoIP prohibits any access to the PSTN. Therefore, set this parameter carefully. The above Note is also suitable for Call VoIP. 1. Set a hotline number in Call PSTN Forwarded-to-number. When the user served by the VoIP network calls the GoIP, the call is forwarded to the hotline number.
VOPTech GoIP User Manual will be connected. 3.7.2.2Trust List Authentication Downlink Uplink The setting is as follows: Select “Forward to PSTN Authentication Mode” > “Trust List Authentication”. Click the “VoIP Trust Number List”, and the VoIP Trust Number List is displayed (Maximum 15 trust numbers can be entered). Enter the trust VoIP number in trust number sequence. If only a VoIP trust number, such as 3306, is set, only the number 3306 can be used to dial the PSTN from the VoIP.
VOPTech GoIP User Manual 3.7.2.3 Password or Trust List Authentication Downlink Uplink This mode is used to set the above password authentication and trust list authentication at the same time. For a downlink call, the authentication mode is as follows: If the number in the trust list is used to dial the user served by the PSTN, the call will be connected. When the number you dialed is not in the trust list, you need to enter the password after the secondary dial tone is played.
VOPTech GoIP User Manual The parameters are defined as follows: SIM card limit time: This parameter sets the total call duration of SIM cards. When the call duration is longer than the specified time (by minutes), the call can not be connected. When this parameter is null, the default call duration is infinite. SIM card status reporting number: The gateway can report the status of SIM cards (remaining call duration) through the SMS.
VOPTech GoIP User Manual is 30 minutes. When the call duration is less than or equals 10 minutes, the gateway will send a short message to 13713652130 (the SIM card ID is 2130 in the reporting message.) to report the remaining call duration. When one-time call duration is longer than 8 minutes, the call will be disconnected. When the call duration is over, it becomes 0. Users can dial the SIM card number by the mobile phone and when the second dialing tone is heard, press *10 to restore the value. 3.
VOPTech GoIP User Manual C: Mode 3 In this mode, the GoIP sets the SIP number of the GoIP as the calling number of the call and the called number as the short message content and the number of the short message sender, whose format is short message content*the number of the short message sender. D: SMS Dial Prefix When the GoIP initiates the SMS call, the GoIP will change the prefix number to the called number prefix.
VOPTech GoIP User Manual Sending Message to 192.168.2.1:5060: INVITE sip:8675588228822@192.168.2.1:5060;transport=udp SIP/2.0 Via: SIP/2.0/UDP 192.168.2.237:5060;branch=z9hG4bK363969813 From: ;user=phone;tag=65248630 To: Call-ID: 117025903@192.168.2.237 CSeq: 2 INVITE Contact:
VOPTech GoIP User Manual CSeq: 2 INVITE Contact: Max-Forwards: 30 User-Agent: VOPTEL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 Mode 2: When a short message of “8675588228822” is sent from the mobile phone number (+86)13800000000 to the GoIP, the GoIP will send the following call requests.
VOPTech GoIP User Manual CSeq: 2 INVITE Contact: Max-Forwards: 30 User-Agent: VOPTEL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 Mode 3: When a short message of “8675588228822” is sent from the mobile phone number (+86)13800000000 to the GoIP, the GoIP will send the following call requests.
VOPTech GoIP User Manual CSeq: 2 INVITE Contact: Max-Forwards: 30 User-Agent:VOPTEL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 3.9.2 SMS Dialing under the H.323 Protocol The GoIP permits users to dial back through the SMS under the H.323 protocol. After users send the called number to the GoIP through the SMS, the GoIP gateway will send a call request to the H.
VOPTech GoIP User Manual In this mode, the GoIP sets the H.323 number of the GoIP as the calling number of the call and the called number as the short message content and the number of the short message sender, whose format is short message content*the number of the short message sender. D: SMS Dial Prefix When the GoIP initiates the SMS call, the GoIP will change the prefix number to the called number prefix. Examples of SMS Dialing: In the following SMS dialing examples, the H.
VOPTech GoIP User Manual Send RAS Message: admissionRequest admissionRequest { requestSeqNum = 241 callType = pointToPoint NULL endpointIdentifier = "3705_endp" destinationInfo = 1 elements { [0] = dialedDigits "8675588228822" } srcInfo = 2 elements { [0] = dialedDigits "20001" [1] = h323-ID "20001" } srcCallSignalAddress = ipAddress { ip = 4 octets { c0 a8 02 ed ....
VOPTech GoIP User Manual answerCall = FALSE canMapAlias = FALSE callIdentifier = { guid = 16 octets { cb 40 a4 af 8e 9b 60 96 6b 5f a0 03 f2 ed 55 5b .@....`.k_....
VOPTech GoIP User Manual [1] = h323-ID "20001" } srcCallSignalAddress = ipAddress { ip = 4 octets { c0 a8 02 ed .... } port = 2049 } bandWidth = 2048 callReferenceValue = 7502 conferenceID = 16 octets { 7f f3 78 77 49 3f 4c c1 9a dc 6a 84 12 d8 30 8f ..xwI?L...j...0. } activeMC = FALSE answerCall = FALSE canMapAlias = FALSE callIdentifier = { guid = 16 octets { cb 40 a4 af 8e 9b 60 96 6b 5f a0 03 f2 ed 55 5b .@....`.k_....
VOPTech GoIP User Manual 3.9.3 SMS Forwarding The GoIP supports the SMS forwarding through the SMS under SIP protocol. After users send the short message to the GoIP through the SMS, the GoIP will send the short message to the specified VoIP number automatically. As shown in the above figure, select SMS Mode > Forwarding and enter the VoIP number that is used to receive the SMS information. The VoIP will automatically forward all the SMS information from the GSM network to this VoIP number.
VOPTech GoIP User Manual 075583185700 2. The SMS sent to the GoIP from the SIP is forwarded to the specified PSTN number. The following example is about the Hello world sent from SIP 3999 to 13682626800. Where, in the content of the SIP message (in red), the first line indicates the number to receive the SMS. The second line indicates the content of the SMS. MESSAGE sip:20001@192.168.2.162:5060 SIP/2.0 From: ;tag=5031 To:
VOPTech GoIP User Manual H323 Terminal SIP Terminal z Disable: It’s not allowed to transfer the PSTN caller number to the VoIP system; z Enable: The CID is set as the SIP caller number. z Use Remote Party ID: The GoIP will add the PSTN caller number to the call request signaling of the VoIP system.
VOPTech GoIP User Manual 3.11 Save the change After setting is changed, click “Save” and the new setting will be valid. Otherwise, the new setting is invalid. Note: Some of parameters of the gateway will not be valid until the gateway is restarted. Therefore, you are advised to restart the gateway after the parameters are modified, so that the modification can take effect. 3.12 Abandon the change When the new setting is not saved, you can clear all the unsaved parameters. Voptel Technology Co.
VOPTech GoIP User Manual 3.13 Tool Select Menu > Tool. The following page is displayed. 3.13.1 Online Upgrading Warning! Only experienced users and administrators can implement the online upgrading. Select Tool > Online Upgrading. The online upgrading page is displayed, as shown in the following figure. Enter the complete name and path of the upgrade package, such as http://voptech.com/update/GHS-4.01-12.pkg , and then click “Start”. The gateway begins to upgrade.
VOPTech GoIP User Manual Note: The password modified by users will be cleared and restored to the factory default password after the factory settings are restored. 3.13.3 Restore Factory Settings Select Tool > Restore Factory Settings. The following prompt is displayed. Click OK. All the parameters of the gateway will be cleared and the gateway will automatically restart. After the gateway is restarted, all the settings restore to the factory default settings.
VOPTech GoIP User Manual Select Tool > Reset to restart the GoIP. 4 Parameters of Equipment Hardware Feature Parameter Parameter Remark Model GOIP GOIP_4 Processor ARM9E 133MHz ARM9E 133MHz DSP VPDSP101 95MHz VPDSP101 95MHz RAM 16M 16M FLASH 4M 4M Power DC12V/2A +-10% DC12V/2A +-10% Input 100V to 240V GSM band Default 900M/1800M Default 900M/1800M Default Optional 850M/1900M Optional 850M/1900M Customized Power consumption Max. 5 W Max.
VOPTech GoIP User Manual Hardware Feature Parameter Remark Model GoIP_8 Customizable Processor ARM9E 133MHz DSP VPDSP101 95MHz RAM 16M FLASH 4M Power DC12V/3A +-10% Input 100V to 240V GSM band Default 900M/1800M Default Optional 850M/1900M Customized 2 pieces Power consumption Max. 20 W LED RUN, GSM, LAN, PC Network adapter 2 100/10BASE-T Weight 1.
VOPTech GoIP User Manual 5 Factory Default Parameter Table Parameter Network Password Default Value LAN Dynamic IP (DHCP) PC Fixed IP: 192.168.8.1 admin admin user 1234 Default time zone Voptel Technology Co., Ltd All Rights Reserved.
