VOOK VOOK HD-SDI QUICK START GUIDE VDT2704XD-P; VDT2708XD-P; VDT2716XD-P
VOOK
4/8/16-CH DVR Quick Start Guide VOOK 1. Hardware installations 1.1 Install Hard Drive Notice: 1.This series support eight SATA hard drives. Please use the hard drive the manufacturers recommend specially for security and safe field. 2. Please calculate HDD capacity according to the recording setting. Step1: Unscrew and Open the top cover Step2: Connect the power and data cables. Place the HDD onto the bottom case as the following picture.
/8/16-CH DVR Quick Start Guide 1 Relay Output. external alarm 2 3 4 5 6 7 Connect to VOOK 8 Network port Connect to external sensor 9 Connect USB mouse or connect external USB devices Connect to speed dome. Y is TX+, Z is TXConnect to keyboard. A is TX+, B is TXHD SDI video signal inputs Connect to high-definition display device VGA output, connect to monitor 10 CVBS output 11 Audio output, connect to the sound box 12 Talk.
4/8/16-CH DVR Quick Start Guide VOOK 2.3 Rear view for 16-ch DVR 1 HD SDI video signal inputs. 9 Connect to speed dome. Y is TX+, Z is TX- 2 Alarm Inputs for connecting sensors Connect to high-definition display device VGA output, connect to monitor Network port 10 CVBS output 11 Audio output, connect to the sound box 12 Talk. Connect to microphone 13 Relay Output. Connect to external alarm. Connect USB mouse or connect external USB devices Grounding Connect to keyboard. A is TX+, B is TX-.
4/8/16-CH DVR Quick Start Guide VOOK Step3: Disconnect the power. 4. Setup Wizard After the device starts, a setup wizard pops up. You can set up time，network , record and disk management. Click Device name box to popup a keyboard as follows: It supports digits, alphabets and symbols as inputs. Click Shift button to input Capital letters and symbols; click Shift button again to return. Click „Next‟ button to bring up a network setup window. The default HTTP port is 80.
4/8/16-CH DVR Quick Start Guide VOOK Select resolution, fps, encode, quality and bitrate. The higher the value is, the clearer the recorded picture is. Of course, more space of HDD will be taken up. Click „Next‟ button. This will take you to the HDD management window. You can check your HDD information through this tab. If your HDD was recently installed, select the HDD from the list to format it. Click „Next‟ button. This will let you to see your DVR status.
4/8/16-CH DVR Quick Start Guide VOOK 6. Main menu setup Click right mouse, or press ENTER button on the front panel to enter into the main menu. Then click Setup to enter into Setup interface as shown below Basic configuration: Users can set video system, menu language, audio, time and authorization check. Live configuration：Users can set name/time display, picture color and hide cameras. Record configuration：Users can set record quality, frame rate, resolution, time stamp and recycle.
VOOK 4/8/16-CH DVR Quick Start Guide data into or from mobile storage medium. 7. Recording Setup A user needs to install and format a HDD, and set all the recording parameters before recording. There are four kinds of record modes. 7.1 Manual Recording A user can press REC button on the front panel after quitting system setup. Press this button again to stop recording. Or press REC button on remote controller. Click it again to stop. Or click REC button on the tool bar with mouse.
4/8/16-CH DVR Quick Start Guide VOOK Step 4: Select other channels and set timeline for them or select „Apply Settings To All Channel and click “Copy” button to set the same settings for all channels. 7.3 Motion Based Recording Motion detection based recording: when there is a motion event detected, the camera will be triggered to record. To Setup Motion Based Recording: Step 1: Enter into MenuSetupScheduleMotion tab.
4/8/16-CH DVR Quick Start Guide VOOK Step 5: Enter into MenuSetupAlarmMotionSchedule tab to bring up schedule settings for motion alarm. The setup steps are similar to normal schedule setup. You can refer to 7.2 Schedule Recording for details. Note: The timelines of the two schedules must match, otherwise you cannot get the record in some time. 7.4 Sensor Based Recording To Setup sensor Based Recording: Step 1: Enter into MenuSetupScheduleSensor tab.
4/8/16-CH DVR Quick Start Guide VOOK 8. Playback This unit supports four kinds of playback 8.1 Live Playback Click Play button on the main menu bar to playback the record. User can do concrete operation by clicking the buttons on screen. 8.2 Playback by Time Search Step 1: Enter into MenuSearchTime Search tab. Step 2: Select date and channels on the right hand side and press “Search” button. A date with highlighted borderline indicates presence of data.
VOOK 4/8/16-CH DVR Quick Start Guide Step 3: Set the start time by clicking a particular grid or by entering the specific value in the start time field. Step 4: Select the channel display mode and click Use the playback toolbar to control the playback. 8.3 button to play record. Playback by Event Search Step 1: Enter into MenuSearchEvent Search tab. Step 2: Select date and channels on the right hand side. A data with highlighted borderline indicates presence of data.
4/8/16-CH DVR Quick Start Guide VOOK Step 4: Once an alarm image has been identified, the user can double click the image to play the recording. You can lock the image by clicking “Lock” button. Click “Save” button to copy the image on the HDD. Click “Save All” to copy all images on the HDD. Note: In order to take images on alarm, the snapshot feature should be activated in “Alarm Handling” for different kind of alarms. Please refer to Alarm Configuration for details. 9.
4/8/16-CH DVR Quick Start Guide VOOK rate etc. ● Open IE on a computer on the same network. Input the IP address of the DVR in IE address bar and press enter. If HTTP port is not 80, add the port number after IP address. ● IE will download ActiveX component automatically. Enter the username and password in the subsequent window 10.2 Access DVR on WAN 1. Connect the DVR to internet through router or virtual server Please enter into MenuSetup Network Setup as shown above.
4/8/16-CH DVR Quick Start Guide VOOK message. ● If users want to utilize dynamic domain name, please apply for a domain name in a DNS server supported by the DVR or router. Then add to the DVR or router. ● When accessing the remote interface of DVR, user can input WAN IP/domain name to access directly (user can enter into Main menuInformationNetwork interface to check IP address). The browser will download Active X control ● The following steps are the same as the connection way above.
