VOOK VOOK QUICK START GUIDE HD-SDI 4-CH DVR VDT2704XE-L
VOOK
4-CH DVR Quick Start Guide VOOK 1. Install Hard Drive &DVD Writer 1.1 Install Hard Drive Notice: 1. Support three SATA hard drives. Please use the hard drive the manufacturers recommend specially for security and safe field. 2. Please disconnect the power before being connected to other devices. Don't hot plug in/out Step 1: Unscrew and Open the top cover to connect the power and data cables. Place the HDD onto the bottom case as Fig 1-1. Step 2: Screw the HDD as Fig 1-2.
-CH DVR Quick Start Guide VOOK Connect to keyboard 9 To connect external USB devices like USB flash, USB HDD for backup or update firmware; or connect to USB mouse 10 VGA output, connect to monitor 3 Connect to high-definition display device CVBS video signal output 11 4 Grounding 12 4-ch Audio inputs Audio output, connect to the sound box 5 1-ch relay output. Connect to external alarm. Alarm inputs.
4-CH DVR Quick Start Guide VOOK Click Device name box to popup a keyboard as follows: It supports digits, alphabets and symbols as inputs. Click Shift button to input Capital letters and symbols; click Shift button again to return. Click „Next‟ button to bring up a network setup window. The default HTTP port is 80. The default server port is 6036.
4-CH DVR Quick Start Guide VOOK up. Click „Next‟ button. This will take you to the HDD management window. You can check your HDD information through this tab. If your HDD was recently installed, select the HDD from the list to format it. Click „Next‟ button. This will let you to see your DVR status. And then Click „Finish‟ button to end this wizard. You can also refer to the complete setup steps from the relevant sections of DVR User Manual.
4-CH DVR Quick Start Guide VOOK Fig 4-2 Main menu setup Basic configuration: Users can set video system, menu language, audio, time and authorization check. Live configuration：Users can set name/time display, picture color and hide cameras. Record configuration：Users can set record quality, frame rate, resolution, time stamp and recycle. Schedule configuration: Users can set schedule for timer, motion detection, and sensor alarm respectively.
4-CH DVR Quick Start Guide VOOK To Setup Schedule Recording: Step1: Enter into MenuSetupSchedule tab. Refer to the following picture. Step2: Click “ ” button to add a certain day schedule; click “ ” button to delete the selected schedule; Step 3: You can also double-click the grid to pop up a week schedule window. Select day and then click „Add‟ button to setup the start time and end time. Then select other days and click „Copy‟ button to save the setting to other days.
4-CH DVR Quick Start Guide VOOK Step3: Enable motion alarm (Please specify to channel) and click „Apply‟ to save settings. Step4: Click „Setting‟ button under the Area to set Sensitivity and Detection area. Left click the grid and drag to delete the area. Drag again to add area. You can drag slide bar to set the sensitivity value (1-8). The higher the value is the more sensitive it is to motion.
4-CH DVR Quick Start Guide VOOK Step 2: Enter into MenuSetupAlarmSensorBasic tab as shown below. Step 3: Enable sensor alarm (Please specify to channel), select senor type and click „Apply‟ to save settings. Step 4: Enter into MenuSetupAlarmSensorSchedule tab to bring up schedule settings for sensor alarm. The setup steps are similar to normal schedule setup. You can refer to 7.3 Schedule Recording for details.
4-CH DVR Quick Start Guide VOOK 8.2 Playback by Time Search Step 1: Enter into MenuSearchTime Search tab. Step 2: Select date and channels on the right hand side and press “Search” button. A date with highlighted borderline indicates presence of data. Step 3: Set the start time by clicking a particular grid or by entering the specific value in the start time field. Step 4: Select the channel display mode and click Use the playback toolbar to control the playback. button to play record. 8.
4-CH DVR Quick Start Guide VOOK Step 2: Select data and channels on the right hand side. Step 3: Press “Search” button to search for a recorded image. Step 4: Once an alarm image has been identified, the user can double click the image to play the recording. You can lock the image by clicking “Lock” button. Click “Save” button to copy the image on the HDD. Click “Save All” to copy all images on the HDD.
4-CH DVR Quick Start Guide VOOK 10. Remote Surveillance In order to view the DVR from a network it must be connected to a LAN/WAN or internet. The network setup should be done accordingly. 10.1 Access DVR on LAN Please enter into MenuSetup Network Setup as shown below: Input IP address, Subnet, Gateway. If using DHCP, please enable DHCP in both the DVR and the router. Enter into Menu Information Network, and user can check the network settings of the DVR.
4-CH DVR Quick Start Guide VOOK Open IE browser, input IP address, or dynamic domain name and enter. If HTTP port is not 80, add the port number after IP address or domain name. IE will download ActiveX automatically. Then a window pops up and asks for user name and password. Input name and password correctly, and enter to view. 2.
