VOOK DVR USER MANUAL VDT2304HD VDT2308HD VDT2316HD For H.
Digital Video Recorder User Manual CAUTION z Please read this user manual carefully to ensure that you can use the device correctly and safely We do not warrant all the content is correct. The contents of this manual are subject to change without notice z This device should be operated only from the type of power source indicated on the marking label. The voltage of the power must be verified before using.
Digital Video Recorder User Manual Table of Contents 1 Introduction ................................................................................................................................................... 7 1.1 DVR Introduction .....................................................................................................................................................................1 1.2 Main Features........................................................................................
Digital Video Recorder User Manual 4.1 Basic configuration ................................................................................................................................................................18 4.1.1 System................................................................................................................................................................................................................ 18 4.1.2 Time & date.................................................
Digital Video Recorder User Manual 4.6 Network configuration............................................................................................................................................................34 4.6.1 Network............................................................................................................................................................................................................... 34 4.6.2 Sub stream.....................................................
Digital Video Recorder User Manual 6.4 Upgrade.................................................................................................................................................................................53 6.5 Logoff ....................................................................................................................................................................................54 7 Remote Surveillance......................................................................
Digital Video Recorder User Manual Appendix F 16-CH DVR Specifications..................................................................................................................................
Digital Video Recorder User Manual 1 Introduction 1.1 DVR Introduction This model DVR (Digital Video Recorder) is designed specially for CCTV system. It adopts high performance video processing chips and embedded Linux system. Meanwhile, it utilizes many most advanced technologies, such as standard H.264 with low bit rate, Dual stream, SATA interface, VGA output mouse supported, IE browser supported with full remote control, mobile view(by phones), etc.
Digital Video Recorder User Manual • • Support built-in SATA DVD writer to backup Support saving recorded files with AVI standard format to a remote computer through internet RECORD & PLAYBACK • Record modes: Manual, Schedule, Motion detection and Sensor alarm recording • Support recycle after HDD full • Resolution, frame rate and picture quality are adjustable • 128MB for every video file packaging • 4 audio channels available • Two record search mode: time search and event search • Support1/4screen play
Digital Video Recorder User Manual SECURITY • Customize user right: log search, system setup, two way audio, file management, disk management, remote login, live view, manual record, playback, PTZ control and remote live view • Support 1 administrator and 15 users. • Support event log recording and checking, events unlimited NETWORK • Support TCP/IP, DHCP, PPPoE, DDNS protocol • Support IE browser to do remote view • Support setup client connection amount • Support dual stream.
Digital Video Recorder User Manual 2 Hardware Installation Notice: Check the unit and the accessories after getting the DVR. Please disconnect the power before being connected to other devices. Don't hot plug in/out 2.1 Install Hard Drive &DVD Writer 2.1.1 Install Hard Drive Notice: Check the unit and the accessories after getting the DVR. Please disconnect the power before being connected to other devices. Don't hot plug in/out 2.2 Install Hard Drive &DVD Writer 2.2.1 Install Hard Drive Notice: 1.
Digital Video Recorder User Manual 2. This device is only for backup Step1: Unscrew and Open the top cover Step2: Connect the power and data cables. Place the DVD writer onto the bottom case as below. Fig 2.1 Connect HDD Fig 2.2 Connect the DVD Writer Step3: Screw the DVD writer. 2.3 Front Panel Descriptions Notice: The front panel descriptions are only for reference; please make the object as the standard. Item Type Work state indicator 1 2 Name Power HDD Net Backup Play REC AUDIO/+ P.T.Z.
Digital Video Recorder User Manual Item Type Compound button Name BACKUP SEARCH Description Enter backup mode in live Enter search mode Record manually Play/Pause Stop/Esc Rewind 3 Digital button 4 Input button 5 USB 1-9 0/10+ Direction button Multi-screen Enter button USB port Fast forward Input number 1-9 or choose camera Input number0, 10 and the above number together with other digital keys Change direction to select items Change screen display mode like1/4/9/16 channel Confirm selection To c
Digital Video Recorder User Manual Fig 2.3 Rear Panel for 4-ch Item 1 2 3 Name Video out Video in E-SATA 4 Spot out 5 6 7 8 9 Audio out MIC IN HDMI port VGA port Audio in 10 USB port 11 12 13 14 15 16 17 18 19 LAN ALARM IN ALARM OUT P/Z K/B GND FAN POWER INPUT POWER SWITCH Description Connect to monitor Video input channels from 1-4 Connect to HDD for backup (optional) Connect to monitor as an AUX output channel by channel.
Digital Video Recorder User Manual The rear Panel interface for 8-ch is shown as Fig 2.6: Fig 2.4 Rear Panel for 8-ch Item 1 2 3 Name Video out Video in E-SATA 4 Spot out 5 6 7 8 9 Audio out MIC IN HDMI port VGA port Audio in 10 USB port 11 12 13 14 15 16 17 18 19 LAN ALARM IN ALARM OUT P/Z K/B GND FAN POWER INPUT POWER SWITCH Description Connect to monitor Video input channels from 1-8 Connect to HDD for backup (optional) Connect to monitor as an AUX output channel by channel.
Digital Video Recorder User Manual The rear Panel interface for 16-ch is shown as Fig 2.7: Fig 2.
Digital Video Recorder User Manual Item 19 Name POWER INPUT Description AC 110V-220V 2.5 Remote Controller It uses two AAA size batteries and works after loading batteries as following: Step1: Open the battery cover of the Remote Controller Step2: Place batteries. Please take care the polarity (+ and -) Step3: Replace the battery cover Notice: Frequently defect checking as following 1. Check batteries poles 2. Check the remaining charge in the batteries 3.
Digital Video Recorder User Manual Item Name Function 1 Power Button 2 INFOR Button 3 4 5 6 7 8 9 10 11 12 13 14 REC Button Digital Button Multi Screen Button SEARCH Button MENU Button ENTER Button Direction Button +/- Button Playback Control Button AUDIO Button Auto Dwell Button BACKUP Button 15 PTZ Control Button Soft switch off to stop firmware running. Do it before power off.
Digital Video Recorder User Manual DVR with the same device ID. For more convenient to operate, we don’t recommend user to set the device ID too long. Step3: Cancel controller to control DVR: turn the IR sensor of the remote controller to the IR receiver that on the front panel, press the number key 8 twice, then input the device ID that needs to be cancelled from controlling, press ENTER button to confirm. After that, the DVR will not be controlled by remote controller. 2.6 Control with Mouse 2.6.
Digital Video Recorder User Manual Users can change some value by the wheel, such as time. Move cursor onto the value, and roll the wheel when the value blinks. It supports mouse drag. I.e. Set motion detection area: click customized, hold left button and drag to set motion detection area. Set schedule: hold left button and drag to set schedule time In playback: Click left button to choose the options. Click right button to return to live mode. In backup: Click left button to choose the options.
Digital Video Recorder User Manual 3 Basic Function Instruction 3.1 Power On/Off Before you power on the unit, please make sure all the connection is good. 3.1.
Digital Video Recorder User Manual 3.2 Login User can login and logout the DVR system. User cannot do any other operations except changing the multi-screen display once logout. Fig 3-1 Login Notice: the default user name and password is “admin” and 123456. The concrete operation steps for change password, add or delete user please refer to User management configuration for more details. 3.
Digital Video Recorder User Manual 3.3.1 Live playback Click Play button to playback the record. Refer to Figure3-3. User can do concrete operation by click the buttons on screen.
Digital Video Recorder User Manual 4 Main menu setup guide Fig 4-1 main menu toolbar Click the icon beside the screen display mode to display a channel select dialog. 6/8/13 channels can realize single channel big screen. Images can drag to any place to display in the live interface. Dwell: Range of selecting to dwell is from single picture preview mode to 1/4/6/9/16 picture preview mode. Color: Click this button; user can adjust the color of live pictures.
Digital Video Recorder User Manual Fig 4-2 system setup 4.1 Basic configuration Basic configuration includes three sub menus: system、 date& time and DST. 4.1.1 System Step1: enter into system configurationÆbasic configurationÆsystem; refer to Fig 4-3: Step2: in this interface user can setup the device name, device ID, video format, max network users, VGA resolution and language. The definitions for every parameters display as below: Device name: the name of the device.
Digital Video Recorder User Manual relevant right in system configuration. Show time: display time in live. Show wizard: tick off this item, there will display an opening wizard with time zone and time setup information Max network uses: set the max user amount of network connection VGA resolution: the resolution of live display interface, range from: VGA800*600、VGA1024*768、VGA1280*1024and CVBS Note： When switch between VGA and CVBS will change the menu output mode, please connect to relevant monitor.
Digital Video Recorder User Manual Step2: in this interface, enable daylight saving time, time offset, mode, start & end month/week/date, etc. Step3: click “default” button to resort default setting; click “apply” button to save the setting; click “exit” button to exit current interface. Fig 4-5 basic configuration-DST 4.2 Live configuration Live configuration includes four submenus: live, host monitor, Spot and mask. 4.2.
Digital Video Recorder User Manual Fig 4-6 live configurationÆlive Fig 4-7 live-color adjustment Step3: in this interface, user can adjust brightness, hue, saturation and contrast in live; click “default” button to resort default setting, click “OK” button to save the setting. Step4: user can setup all channels with same parameters, tick off “all”, then do relevant setup. 4.2.
Digital Video Recorder User Manual Click button to set the latter channel groups of dwell picture. Step5: click “default” button to resort default setting; click “apply” button to save the setting; click “exit” button to exit current interface. 4.2.
Digital Video Recorder User Manual Setup mask area Live image mask area 4.3 Record configuration Record configuration includes six sub menus: enable, record bit rate, time, recycle record, stamp and snap. 4.3.
Digital Video Recorder User Manual Step2: tick off record, audio and record time Step3: user can setup all channels with same parameters, tick off “all”, then to do relevant setup. 4.3.2 Record stream Step1: enter into system configurationÆrecord configurationÆrecord bit rate; refer to Fig 4-12: Step2: setup rate, resolution, quality, encode and max bit stream Step3: user can setup all channels with same parameters, tick off “All”, then to do relevant setup.
Digital Video Recorder User Manual triggered. Post-alarm record: set the post recording time after the alarm is finished, five options: 10s, 15s, 20s, 30s, 60s, 120s, 180s and 300s. Expire time: the hold time of saved records. If the set date is overdue, the record files will be deleted automatically. Step2: u user can setup all channels with same parameters, and then tick off “all” to do relevant setup.
Digital Video Recorder User Manual Before drag after drag 4.3.5 Recycle record Step1: enter into system configurationÆrecord configurationÆrecycle record; Step2: tick off recycle record to enable the recycle record function. It will cover the earlier recorded files and keep recoding when HDD is full; if user disenables this function, it will stop recording when HDD is full.
Digital Video Recorder User Manual Fig 4-15 schedule configuration-schedule Step2: select channel and double-click to pop up a window as Fig 4-16. Now user can edit week schedule: ① ② Fig 4-16 schedule-week schedule Click “add” button to add a certain day schedule; click “delete” button to delete the selected schedule; Copy: user can copy the specify schedule to other dates. Click “OK” button to save the setting; click “Exit” button to exit current interface.
Digital Video Recorder User Manual Fig 4-17 schedule configuration-motion Note: the default schedule of motion detection is full-selected, that is, the color of schedule setting interface is blue. 4.4.3 Sensor Step1: enter into system configurationÆschedule configurationÆalarm; refer to Fig 4-18: Step2: the setup steps of alarm are familiar with schedule; user can refer to 4.4.1 Schedule for details.
Digital Video Recorder User Manual 4.5.1 Sensor Sensor includes three sub menus: basic, alarm handling and schedule. ① Basic Step1: enter into system configurationÆalarm configurationÆsensorÆbasic; refer to Fig 4-19: Step2: enable sensor alarm and then set the alarm type according to triggered alarm type. Two option: NO and NC. Step3: user can setup all channels with same parameters, tick off “all” to do relevant setup.
Digital Video Recorder User Manual Fig 4-20 alarm configuration-sensor-alarm handling Fig 4-21 alarm handling-trigger Step 3: If Buzzer is selected, there will be triggered buzzer alarm out. Full screen alarm: when alarm is triggered, there will pop up full screen alarm; Email: Select this function. When an alarm is triggered, a notification email will be sent to user’s designed email box including trigger events, time, snap pictures, device name, ID camera name etc. Snap: Select channels.
Digital Video Recorder User Manual Step1: enter into system configurationÆalarm configurationÆmotion; refer to Fig 4-23: Step2: enable motion alarm, set alarm hold time which means time interval between two adjacent detective motions. If there is other motion detected during the interval period which is considered continuous movement; otherwise, it will be considered that those two adjacent detective motions are two different motion events.
Digital Video Recorder User Manual Note: when user drag mouse to set motion detection area, they have to click firstly, and then make the operation. Step6: user can setup all channels with same parameters. Step7: click “default” button to resort default setting; click “apply” button to save the setting; click “exit” button to exit current interface.
Digital Video Recorder User Manual Fig 4-26 alarm configuration-video loss 4.5.4 Other alarm Step1: enter into system configurationÆother alarm; refer to Fig 4-27: Disk full: user can choose the capacity of the disk storage and select the related alarm. If the disk is full, the system will alarm according to the setup. IP conflict: if there is an IP address conflict within the same network, the device will alarm after user selects buzzer and the channel to alarm out.
Digital Video Recorder User Manual 4.5.5 Alarm out Alarm out includes three sub menus: alarm out, schedule and buzzer ① Alarm out Step 1: enter into system configurationÆalarm out; refer to Fig 4-28: Step 2: in this interface, user can set relay alarm out name and select hold time which means the interval time between the two adjacent alarms. Step 3: user can setup all channels with same parameters.
Digital Video Recorder User Manual into IE browser. subnet mask, and gateway IP and DNS server. Step 4: enable PPPoE to directly connect the DVR to internet via ADSL, and then input the user name and password. Next, click TEST button to test the effectiveness of the relevant information. Server port: communication port. Step 3: If user selects the "Obtain an IP address automatically", the device will distribute IP address, Fig 4-29 network configuration-network 4.6.
Digital Video Recorder User Manual Step 1: enter into system configurationÆnetwork configurationÆsub stream; refer to Fig 4-30: Step 2: select fps, resolution, quality, encode and max bit rate Step 3: user can setup all channels with same parameters. Tick off “all” to do relevant setup. Fig 4-30 network configuration-sub stream Definitions and descriptions of Sub stream: Parameter FPS Resolution Quality Encode Max bit rate Meaning Range from: 1-25 Support CIF The quality of the clients’ image.
Digital Video Recorder User Manual SMTP Server/Port: the name and port number of SMTP server. After selecting “This server requires a secure connection (SSL)”, user can setup mail servers (such as Gmail) according to actual needs. Send address/password: sender’s email address/password Receive address: receiver’s email address. Here user can add at least three mail addresses. Click TEST button to test the validity of the mailbox.
Digital Video Recorder User Manual Note: The domain name server that selected by user is a banding domain name of DVR. User should logon the website which provided by the server supplier to register a user name and password firstly, and then apply for a domain name on line. After the successful application, user can access the server from the IE client by inputting that domain name.
Digital Video Recorder User Manual If “Show icons for networked UPnP devices” can’t display in the “Network Tasks” list box, please follow the below operation: z Click “Tools”-- “Folder options” z Select the “Show common tasks in folders” in the “Tasks” check box to display the UPnP icon. 1． Domain name Registration （Take www.dyndns.com for example） Note: Users can self-define the hostname, username and password. Input www.dyndns.
Digital Video Recorder User Manual After user fill in the blank, click “Add to cart”. Then Dynamic DNS Hosts dialog box will be displayed. Next, create user account. For example, the username is “bcd”, password is “123456”. Click” Create Account” button to create user account. 2． DVR Setting （1） Domain name According to the domain name registration of “DDNS”，the domain name for DVR is “abc.dyndns.
Digital Video Recorder User Manual According to the above registration, username is “bcd”. According to the above registration, password is “123456” 3． Application Connect DVR to the Network Client. ① Enter into Main menuÆNetworkÆother settings, tick off DDNS, select “Dyndns” at the DDNS Sever pull down list box and input user name and password. ② Enter into configuration interface of the router to map the server port and IP address (if the user enables UPnP function, he can skip this step).
Digital Video Recorder User Manual Fig 4-33 user management configuration Fig 4-34 add-general ① General: Input user name, password; select user type: normal and advance, input the MAC address of the PC; click OK button. Then this user will be added into the user list box; click Exit button to exit the current interface.
Digital Video Recorder User Manual 4.8 P.T.Z configuration P.T.Z configuration includes two submenus: serial port and advance ① Serial port Step 1: enter into system configuration Æ P.T.Z configurationÆserial port; refer to Fig 4-36: Step 2: tick off Enable and then setup the value of address, baud rate and protocol according to the settings of the speed dome. Step 3: user can setup all channels with same parameters. Fig 4-36 P.T.
Digital Video Recorder User Manual Fig 4-37 P.T.Z configuration-advance Fig 4-38 advance-preset setting a. in the preset set interface, while clicking Setting button, a dialog will pop-up as Fig 3-39: Fig 4-39 preset set-setting b. user can control the dome rotates up, up left, down, right down, left , left down, right and up right and stop rotating; adjust the rotate speed and the value of zoom, focus and iris of the dome; c. select the serial number of the preset point. Click PTZ light.
Digital Video Recorder User Manual Fig 4-40 cruise set a. click Add button to add cruise line in the list box (max 8 cruise line can be added); select a cruise line and click Setup button to see a dialog box as Fig 4-41: b. click Add icon to set the speed and time of preset point; select a preset point and then click Delete icon to delete that preset point; click Modify icon to modify the setting of a preset point. User can click those icons to adjust the position of preset point.
Digital Video Recorder User Manual Fig 4-41 cruise set-modify cruise line a. user can control the dome rotates up, up left, down, right down, left, left down, right and up right and stop rotating; adjust the rotate speed and the value of zoom, focus and iris of the dome; click Start Record button to record the move track of PTZ; click this button again can stop record; click Start track button to play recorded track; click this button again can stop play. b.
Digital Video Recorder User Manual users within a certain IP address segment to access DVR, they can tick off Allow-list, and then operate in the same way.
Digital Video Recorder User Manual 5 Record search & playback and backup Search configuration includes four submenus: time search, event search, file management and image. 5.
Digital Video Recorder User Manual Note: the vertical column means hours, horizontal column means channels. Step4: click Play button to playback record; click the relevant buttons on the screen to do operation: Playback buttons Note: when the monitor resolution is VGA800*600, the time search interface will appear a hide button, click this button, the whole interface can be expanded. 5.
Digital Video Recorder User Manual Then tick off Motion, Sensor or All accordingly. Step3: double check a certain record file to playback. Note: when the monitor resolution is VGA800*600, the event search interface will appear a hide button. Then click this button to expand the whole interface. 5.
Digital Video Recorder User Manual 5.4 Image In this interface, user can set start, end time and channels to search the captured images and save, lock or delete these images. There are at most 2000 images which can be saved in the SATA disk. If there are more images saved in the SATA disks than 2000 images, those additional images will supersede prior images. Double click the image with the left mouse, it will automatically playback from the time of the image captured. 5.
Digital Video Recorder User Manual Step4: in the backup information interface, user can check the relevant information of backup files, storage type, save file type, etc. Then click Start button to starting backup. 6 Manage DVR 6.1 Check system information Check system information includes five submenus: system, event, log, network and online user. 6.1.1 System information In this interface, user can check the hardware version, MCU version, kernel version, device ID, etc. 6.1.
Digital Video Recorder User Manual 6.2 Manual alarm In this interface, user can check the relevant parameters of manual alarm. 6.3 Disk management 1. Format the disk Step1: enter into disk management interface Note: please format the hard disk before record. If not being formatted, it will show the status of the disk-free space, and total space show OM at the bottom of screen.
Digital Video Recorder User Manual 6.5 Logoff Click Log off icon, a log off dialogue box will popup, click OK button, the device will log off. If user wants to log in again, click icon to enter into user name and password to re-login.
Digital Video Recorder User Manual 7 Remote Surveillance 7.1 IE Remote Surveillance In order to view the DVR from a network it must be connected to a LAN/WAN or internet. The network setup should be done accordingly. Please refer to 4.6 Network Setup. This DVR supports IE browser, on Windows XP and Vista platform. 7.1.1 On LAN Step 1: Enter into the DVR’s Main MenuÆSetupÆNetwork interface to input IP address, Subnet Mask, etc .If using DHCP, please enable DHCP in both the DVR and the router.
Digital Video Recorder User Manual after IP address or domain name. Step 6: IE will download ActiveX automatically. Then a window pops up and asks for user name and password. Input name and password correctly, and enter to view. FAQ Note: If you cannot download and install ActiveX, please refer to Appendix A Q8. 2. Connect the DVR to internet directly. Step 1: Enter into the DVR’s Main MenuÆSetupÆNetwork interface to enable PPPoE and then input user name and password received from your ISP.
Digital Video Recorder User Manual 7.2 Remote Surveillance through Apple PC Note: Because the current plug-in version of client end just only supports 32-bit mode, so the safari browser shall start 32-bit mode. If the browser is the earlier MACOS version, the default setting is 32-bit mode and the setting can be skipped. The Setting steps are as follows: First: Right click safari icon and select “Show in Finder”. Second: Select ApplicationsÆRight click “Safari. App”ÆSelect “Get Info”.
Digital Video Recorder User Manual 7.2.1 On LAN Step 1: After starting Apple computer, click icon. The following window will pop up.
Digital Video Recorder User Manual Step 2: Enter into Network interface and then click “Ethernet Connected” to check the internet connection of Apple PC. Step 3: After acquiring the IP address, Subnet Mask and so on, please enter into the DVR’s Main MenuÆSetupÆNetwork interface to manually input IP address, Subnet Mask and Gateway according to the configuration of PC. The network segment should be the same as the PC. If using DHCP, please enable DHCP in the DVR and router.
Digital Video Recorder User Manual http://192.168.1.100:81(here 192.168.1.100 is LAN IP of DVR, 81 is the http port of DVR). Click “ will download Active X control as shown below: ”button, the browser icon and then select the Active X control, the welcome interface will be shown. Click Step 5: Click “Continue”Æ”Install” button，the following window will pop up： Input the name and password of Apple PC and then click “OK” to install this Active X control.
Digital Video Recorder User Manual 7.2.2 On WAN There are also two ways for DVR to connect to Internet. 1. Connect the DVR to internet through router or virtual server Step 1: The network setups are the same as step one to step four of point 1 on WAN of IE remote surveillance. Step 2: Enter WAN IP and http port in the Safari browser to install the Active control. The concrete steps are the same as step 5 and 6 of Chapter 7.2.1. 2. Connect the DVR to internet directly.
Digital Video Recorder User Manual 7.3 The remote live preview interface Fig 7-2 Remote live preview interface Symbol and function Definitions: ① Channel indicator ④ Snapping picture ⑦ Bidirectional talk ⑩ PTZ control Note: click ② ⑤ ⑧ ⑪ Screen display mode Start manual record Playback Master/sub stream status ③ ⑥ ⑨ Volume Start IE record Color button to record manual and the record file will be saved in user’s PC.
Digital Video Recorder User Manual Screen display mode: Click the icon beside the screen display mode, channel select dialog will appear as below: Take 8-channel DVR for example: user can tick off channels form 1-ch to 16-ch at random to display the live pictures, 8 channels can be selected at most. Then click OK button to confirm the setting. Fig 7-3 Channel select dialog Snap pictures icon, the system will automatically capture pictures and save those pictures in the computer.
Digital Video Recorder User Manual Buttons definition: Buttons Description means the dome rotate up. means the dome rotate up left. means the dome rotate up right means the dome rotate down. means the dome rotate left down. means the dome rotate right down. means the dome rotate left. means the dome rotate right. means the dome stop rotating. Drag the scroll bar to adjust rotating speed of the dome. button near 'Iris' button to increase light of the dome. Click 'Iris' button.
Digital Video Recorder User Manual Fig 7-4 right key sub menu Stream: this DVR supports master stream and sub stream. Master stream has higher frame rate, max 25FPS（PAL）/30 FPS （NTSC）for every channel, but it needs higher network bandwidth simultaneously; second stream has low frame rate, max 6FPS （PAL）/7FPS（NTSC） for every channel, it requires low network bandwidth. Therefore, users can select the stream according to their bandwidth.
Digital Video Recorder User Manual Fig 7-5 Play record file interface This DVR supports remote time search, event search and file management.
Digital Video Recorder User Manual Fig 7-6 time search interface Step2: click “Search” button. The record data will be displayed in the data information list box; the highlight date in the area② means have record data, click those data; select the record channels in area③ Step3: User can set the data playing time and display mode in the area① as required Step4: Select certain item from the data information list box.
Digital Video Recorder User Manual Fig 7-7 Time search playback By Event Search: Step1: Enter into SearchÆevent search; refer to Fig 7-8: VOOK premium DVR 68
Digital Video Recorder User Manual Fig 7-8 event search interface Step2: click the highlight date and select record channels and then tick off the event type: motion and sensor.
Digital Video Recorder User Manual Fig 7-9 file management interface Lock: select certain file item in the file list box and then click “Lock” button to lock this file that ca not be deleted or overlaid Unlock: select a locked file and then click “unlock” button to unlock this file Delete: select an unlock file and then click “delete” button to delete this file from file list VOOK premium DVR 70
Digital Video Recorder User Manual 7.4.2 Remote backup Click Backup button to enter into backup interface, refers to Fig 7-10: Fig 7-10 remote backup interface Step1: select channels, set the start and end time and then click “search’ button to display the file information in the file list box Step2: select backup files and click “browse” button to set the save path. Then click “backup” button to start backup. The backup files will be saved on user’s PC.
Digital Video Recorder User Manual 7.5 Remote System configuration User can remote setup the parameters of the device. Functions of remote configurations include: basic configuration, live configuration, record configuration, schedule configuration, alarm configuration, network configuration, PTZ configuration and user configuration. User should firstly select an item in the menu list on the left, and then setup the relative parameters.
Digital Video Recorder User Manual 7.6 Remote Management Remote Information Search The system will automatically record the working condition and operation process during the period of work. User can view information, such as username, IP address and so on. Enter into INFO→Log. User can set the start time to view the log record as follows: Fig 7-12 Remote information search Note: There may be subtle differences with respect to functions of remote surveillance between through IE and through Apple PC.
Digital Video Recorder User Manual 8 Mobile Surveillance This DVR supports mobile surveillance by Iphone, Gphone，blackberry or smart phones with Windows mobile and symbian OS. At the same time, it supports 3G network. We tested Dopod D600 (WM5) and Dopod S1 (WM6), which work fine with the DVR. It wants to make mobile surveillance, need first enable network service on the DVR, and refer to Chapter 4.6 Network configuration. The below is the use instructions on mobile client end for two OS. 8.
Digital Video Recorder User Manual to log on the server. It will show the picture if access successfully. Refer below picture in the left: Step6：Camera 1 is the default channel after login. Change the channel in rolling-down menu of “Channel”: refer below picture in the right: Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. 8.2 By Phones with Symbian Please use the smart phones with symbian version supported by this unit.
Digital Video Recorder User Manual Step2：Input the DVR server’s IP address in a new-built bookmark. Click this bookmark to connect to the DVR. Refer picture in the left: Step3：A welcome window will pop up and requires a package. Click the software name to download. Refer picture in the right: Step4：A security windows will pop up after downloading and ask if install the package. Click YES to install. Step5：A Scam shortcut icon appears on the system menu after finished. Step6：Run Scam program.
Digital Video Recorder User Manual Step9：Enter Live View, it will connect the server and display pictures. Refer picture in the left: Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. Step10：In Live View, users can do snapshot, change channels and control PTZ. Refer picture in the right: 8.3 The Software installation for iPhone mobile clients 1. Install through iphone. Step 1. Open App Store function of iphone Step 2.
Digital Video Recorder User Manual Step 3: Click SuperCam, enter into “introduce” interface and then click “FREE”, it will change into “INSTALL” Step 4: Input iTunes Store password and then click “OK”, the software will be installed automatically. Note: if it was the first time for user to operate, please enter user ID; if there is no Store account, user needs to apply one. 2. Install through PC.
Digital Video Recorder User Manual Step 1: Install iTunes store in PC and then login Step 3: Enable “search” Step 2: Connect iPhone and PC function to search “SuperCam” VOOK premium DVR Step 4: Click “free application” button 79
Digital Video Recorder User Manual Step 5: Input apple ID and password, then click “acquire” Step 6: Tick off “synchronously apply program” and “SuperCam”, and then click “apply” button Operation Instruction for SuperCam (iphone) 1. Login interface Enter server’s IP address (or domain name), user name and password Click “Remember server” to save the setting; click button can quick input saved server address, user name and password.
Digital Video Recorder User Manual 2. Main Interface 【Playback】 【Log】 【Live】 【Information】 【Logoff】 3.
Digital Video Recorder User Manual Group 4. 5.
Digital Video Recorder User Manual Click the record file to playback. 6. Server list Interface, refer to below picture in the left: 7. Config interface, refer to below picture in the right: Main parameters for mobile phone video config Record file clip size: Single video size.
Digital Video Recorder User Manual 8.
Digital Video Recorder User Manual Step 3: press “Install” button Step 4: click “OK” button Step 5: user can view the download and install process in notifications; finished download, the software will install automatically.
Digital Video Recorder User Manual Login Enter into server’s IP address (or domain name), user’s ID and password. Click “Remember server” to save the setting; click button can quick input saved server address, user name and password.
Digital Video Recorder User Manual Mark 1 ( Fig 1） Current viewing channel Mark 2 （Fig 2） Channel status Switch channels PTZ, click to switch to Fig 2 interface Snap record talk Live audio Full screen Return Upward rotates the PTZ Downward rotates the PTZ Leftward rotates the PTZ Rightward rotates the PTZ Stop rotates the PTZ Zoom In/Focus In/Iris Add Zoom Out/Focus Out/Iris Sub Preset Select the preset point VOOK premium DVR 87
Digital Video Recorder User Manual Group Set the cruise line Image view Previous Next Zoom out Delete Zoom in Return to main menu Record playback Play/pause Full screen stop Return to record file interface (Fig 3) （Fig 3） （Fig 4） Click the record file (Fig 3) to playback (Fig 4) Server list VOOK premium DVR 88
Digital Video Recorder User Manual Config interface Alarm setting Storage setting Path Reserved disk space Video clip size Remove all recorder files before Tick off Sound Alarm ， when Video Loss/Sensor/Motion happen ， trigger sound alarm; Tick off Vibrate Alarm, when Video Loss/Sensor/Motion happen，trigger vibrate alarm User can setup the relevant parameters of mobile video. This function can be valid only insert SD card. Save path for mobile video files, the default catalog is /SDCard/.
Digital Video Recorder User Manual Information view 8.5 Installation and operation Methods for BlackBerry Mobile phone Client 8.5.1 Installation instruction for BlackBerry Mobile phone Client 1. Open the browser of BlackBerry phone and enter sever address 2. Click “SuperCam” to link 3. Click “Download” button on the popup interface and the download progress will be shown.
Digital Video Recorder User Manual 4. Finished downloading, the software will be installed automatically. Note: If the software fails to download, please check in accordance with the following steps: 1. Check whether the network of mobile phone is normal or not 2. Check whether DVR server connect network normally or not 3. Modify the option of Browser Configuration. (1) Enter into Menu->Option->Browser Configuration; configure referring to the following figure in the left.
Digital Video Recorder User Manual Note：When user used the SuperCam software in mobile phone with touch screen, there will be compatible problem. Solution: Enter into Options Menu->Advance options->Applications->SuperCam and click “Disable Compatibility” button. This problem will be solved. 8.5.2 Operation method for Blackberry mobile phone client 1. Login Enter server’s IP address (or domain name), user’s ID and password.
Digital Video Recorder User Manual 2. Main interface Playback Log Information Logoff Live 3.
Digital Video Recorder User Manual Note: User can click Mark 1 Preset Return button on the Blackberry phone to return the previous interface.
Digital Video Recorder User Manual 4. Server list 5. Software configuration 6.
Digital Video Recorder User Manual Appendix A FAQ Q1. Why the DVR cannot start after connected to the power? a. The adapter has been damaged. Please change an adapter b. The power of the adapter is not enough. Please remove the HDD to check c. Hardware problem Q2. There is not menu output or only has live image display a. Check up whether other devices can display menu or long press ESC key to wait for login dialog box to appear. Q3. The indicator of the DVR lights, but no output. Why? a.
Digital Video Recorder User Manual Q6. Cannot record a. Don't format HDD. Please format it manually first. b. Don't enable record function or incorrect setup. Please refer to Chapter 5 Record search & playback and backup. c. HDD is full and not enables recycle function. Please refer to Record Configuration. Chang a new HDD or enable recycle. d. The HDD is damaged. Change a new one. Q7. Cannot use mouse. a. wait 1-2 minutes after mouse connected. b. Not detected. Plug/unplug several times. c.
Digital Video Recorder User Manual ② select Security------Custom Level….Refer to Fig 8-1 ③ Enable all the sub options under “ActiveX controls and plug-ins” refer to Fig 8-2 ④ Then click ok to finish setup. b. Other plug-ins or anti-virus block ActiveX. Please uninstall or close them.
Digital Video Recorder User Manual First possible reason: hard-disk cable and data cable are not well connected.
Digital Video Recorder User Manual RAM VGA OS DirectX 512M NVIDIA GeForce MX440/FX5200 ATIRADEON 7500/X300 Windows 2000(SP4 above) /Windows XP(SP2 above) /VISTA 9.0 Q13: What are the PC configurations for 16-ch real time product with fully open channel mainstream? PC Module Parameters CPU Intel Core(TM)2 Duo CPU E4600 Motherboard G31/P31 chip HDD 80G RAM 1GB VGA GMA3100/NVIDIA GeForce 8400/ ATI RADEON HD3450 OS Windows 2000(SP4 above) /Windows XP(SP2 above) VISTA DirectX 9.
Digital Video Recorder User Manual b. Right click IE browser (refer to Fig 14-2), select Run as administrator to run browser.
Digital Video Recorder User Manual Appendix B Calculate Recording Capacity Users can calculate the size of hard disk according to the saving time and DVR recording settings. The DVR uses fixed video bit rate. The below are the details at different settings. Frame Rate Video Video Quality Bit Rate (kbps) Used Space(MB/h) Resolution Totally(FPS) Format Highest 2M 915 Higher 1.5M 700 25 PAL D1 Medium 1M 465 Lower 768K 297 Lowest 512K 241 Highest 2M 910 Higher 1.
Digital Video Recorder User Manual Appendix C Compatible Devices 1. Compatible USB drive after test. Brand SSK Netac Kingston Aigo Smatter vider SanDisk Capacity 512MB, 1G, 2GB 4GB 2GB 2GB 1GB 4GB Tab C.1 Compatible USB drive 2. Compatible SATA CD/DVD writers after test Brand TECLAST BENQ LITEON LITEON SAMSUNG Model GH22NP20/TL-22XD DW220S-0K4 DH—20A6S01C DH-20A4P02C TS-H653B Tab C.
Digital Video Recorder User Manual 3. Compatible HDD list Brand Seagate Barracuda LP ST3200542AS Seagate Barracuda 7200.11 ST31500341AS Seagate SV35.3 ST31000340SV Seagate Pipeline HD.2 Seagate Barracuda 7200.10 Seagate Barracuda 7200.10 ST3250310AS Seagate Barracuda 7200.11 ST3160813AS Seagate Barracuda 7200.10 ST380815AS Maxtor Diamondmax 21 STM3160215AS HITACHI Deskstar HDS721616PLA380 HITACHI Deskstar WD WD1600JS Samsung HD161HJ VOOK premium DVR Capacity 2TB 1.
Digital Video Recorder User Manual Appendix D 4-CH Specifications Compression format Video output Video input VGA Resolution H.264 Main Profile Composite：1.0V p-p/75Ω BNC×2 , VGAX1 Composite：1.
Digital Video Recorder User Manual Appendix E Compression format Video output Video input VGA Resolution Record Resolution 8-CH Specifications H.264 Main Profile Composite：1.0V p-p/75Ω BNC×2 , VGAX1 Composite：1.
Digital Video Recorder User Manual Appendix F Compression format Video output Video Input VGA Resolution 16-CH Specifications H.264 Main Profile Composite：1.0V p-p/75Ω BNC×2, VGAX1 Composite：1.
450011000155 A2 VOOK premium DVR
