H Series——with Pan/Tilt of CMOS IP Camera (Version 2.2) 2010.
H Series IP Camera User Manual – with Pan/Tilt of CMOS Index 1 INTRODUCTION ........................................................................................................................... 4 2 FUNCTION AND FEATURES ..................................................................................................... 4 3 APPEARANCE AND INTERFACE ............................................................................................. 6 4 5 3.1 APPEARANCE ..............................
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7.4 7.4.1 User Management .............................................................................................................. 22 7.4.2 Auto Capture Setting .......................................................................................................... 23 7.4.3 E-mail Setting .................................................................................................................... 23 7.4.4 FTP Setting .............
H Series IP Camera User Manual – with Pan/Tilt of CMOS 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet. Your IP Camera package should contain the following items, If any of the listed items are missing, please contact your reseller from where you purchased the camera for assistance.
H Series IP Camera User Manual – with Pan/Tilt of CMOS VGA/QVGA/QQVGA resolution optional. User can change some specification according to their demands to satisfy his own visual prefer. Built-in microphone, and also support external audio signal, support live audio recording; External speaker can play the voice sent to the live scene, to achieve two-way intercom function. Built-in Pan/Tilt, horizontally 350°, vertically 100°.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 3 Appearance and interface 3.1 Appearance Figure 1 3——Photovaristor 1——IR Lights 2——Lens 4——Internal Mic Hole 5——Power Indicator 6——WIFI Indicator 7——Shell 8——Heat Dissipation Hole 9——SD Card Socket Remarks: Power Indicator: it will turn RED if equipment was powered on. WIFI Indicator: If there is a WIFI module in the equipment, and there is data transferring by WIFI, it will begin twinkle. 3.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 2) WIFI Antenna Hole: Install the WIFI antenna. 3) RESET Button: Press the RESET button and hold on more than 5 seconds, the equipment will restart and recover to the factory default settings. The Pan/Tilt will move around for one circle and finally focus to the center. 4) RJ45 Ethernet Socket: RJ45 Ethernet socket is 10/100M self-adjust. The equipment can connect to all kinds of network equipments, such as hub, router, switch, etc.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 4 Network Connecting Figure 5 IP Camera can be connected with other PC through router, switch or hub to establish a network. Figure 5 shown connections. 4.1 Connection Instruction Before visit the IP Camera, you should firstly connect it to the Network, supply the power to it, and check if the light of RJ45 Socket is normal to make sure all of the communication links are fluency. The connection method likes as Figure 5.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 2) The PC and IP Camera are in different LANs, but they are all connected to Internet. For the IP Camera-1 and PC-2 in Figure 5, if you want to visit IP Camera-1 by PC-2, you should firstly do the setting as 1) to make sure that you can visit IP Camera-1 through PC-1 and then do the setting of router-1 (do the port forwarding from the router). The PC-2’s visit application could be sent through router-1 to IP Camera-1.
H Series IP Camera User Manual – with Pan/Tilt of CMOS IP Camera by default use fixed IP address 192.168.0.158 and fixed http port 80. If you don’t have this software, you could also press down the reset button (Figure 2) to go back the factory setting. Then you could use this defaulted IP address to visit the IP Camera. Setting Instruction: Please carefully check the “Local PC information” on the top left corner which lists the PC configuration.
H Series IP Camera User Manual – with Pan/Tilt of CMOS Figure 8 After the ActiveX installation, click the “Video View” as Figure 7, then you will enter the video view home page as below Figure 9. Figure 9 5.2.1 Menu column There are 2 kinds of menu, one is main menu, the other is submenu. The main menu lies at the top of the interface, including View, Media, Network, Alarm, Advanced and System; Submenu lies on the left of the interface, and different main menu is in line with different submenu. 5.2.
H Series IP Camera User Manual – with Pan/Tilt of CMOS of the certain area, it will show a pane to call user’s attention. Figure 10 is status column at the bottom of video displaying area. Figure 10 1) Displaying how many users are visiting this video. 2) If user has clicked the “Record” button in the Figure 9, here will show “Rec”, means the video is being recorded. If click the “Record” button again, it will stop recording. 3) Play/Pause Button: Click it for video play or pause video play.
H Series IP Camera User Manual – with Pan/Tilt of CMOS you it is recording. Click the “Record” button again, and then the record stops. 5.2.6 Playback Click “Playback” button, it will pop up a player which could play the video stored on your PC disk. Figure 12 , these buttons are for play, stop, the previous recorder, the next recorder, open the recorder file. Please click the button of “open the recorder file” first, and select the file you want to play, you can playback the recorder. 5.2.
H Series IP Camera User Manual – with Pan/Tilt of CMOS the IP Camera -1 into WAN. You can set port forwarding on Router-1 to put IP Camera-1 into WAN. Open the Router Setting interface on PC-1. The interfaces for different routers are different, and the port forwarding settings are different, please refer the router manual to set. For most routers, “Virtual server” option can be found in setting interface. Fill the IP address and port of IP Camera-1 into corresponding blank. Figure 13 is an example.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 6.2.1 Manufacturer’s Domain Name Device manufacturer has established a DDNS, and allotted a dynamic domain name to every device, the domain name has been integrated into devices when producing. For example, enter domain name of Figure 14, the browser will connect the device and display the IP address.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7 Other Settings 7.1 Video Setting Page 7.1.1 Image Setting Figure 16 1) Color Adjustment: Drag the glide bar showed as above Figure 16, user can adjust the brightness, saturation, contrast, hue. 2) Image Display Adjustment: There are “Flip” and “Mirror” two options, select it for the image display. 3) Night vision mode: If you choose “auto” mode, IR lights will be lighted on and shut off by the photoresistance.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7.1.2 Video Setting Figure 17 1) Resolution Adjustment: There are VGA(640*480)、QVGA(320*240)、QQVGA(160*120) three resolution options. The bigger the resolution is, more clear the image will be. On the other hand the bit rate is bigger and takes more bandwidth. 2) Bit Rate Adjustment: User can choose a certain bit rate, generally speaking, the bigger the bit rate is, the more clear the image will be.
H Series IP Camera User Manual – with Pan/Tilt of CMOS There are two frequencies on the world, one is 50HZ, and the other is 60HZ. In China, adopt 50HZ. 7) Audio input mode: If user use microphone, please select “MIC”; if use line-in audio signal (like sound pick-up), please select “Line in”. 8) OSD Setting: User can add the equipment’s name and the time on the video page thorough this setting. 7.2 Network Setting Page 7.2.
H Series IP Camera User Manual – with Pan/Tilt of CMOS Figure 19 If you have set wifi, please unplug the network cable, and power on the ip camera again for rebooting it, then the wifi will work. 7.2.2 Remote Access Setting Figure 20 1) WAN IP Test: Click the “Show” button as above Figure 20, it will show you another new page displaying the WAN IP address when it is connected to the Internet.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 2) Manufacturer’s DDNS and Third Part Dynamic DNS: Please refer to the content of the part 6.2. 3) UPNP: UPNP stands for universal plug and play, if you started UPNP, once the IP camera was connected into the LAN, it will communicate with the router of the LAN. It will request the router to open a port to forward its own port. User doesn’t need to log in the router to set the port forwarding.
H Series IP Camera User Manual – with Pan/Tilt of CMOS supports four areas settings. By ticking the options, on the screen, it will show you the area frame, and the areas are numbered. Using the mouse to drag the area frame, you can change the position of the frame, and to drag the right bottom corner of frame, you can change the size of frame. After setting is finished, click “Apply“ button, then the motion detection is enabled. 7.3.
H Series IP Camera User Manual – with Pan/Tilt of CMOS IP Camera will trigger alarm only on the time set by Figure 24. Please adjust the system time first. Refer to Part 7.5.1 7.4 Advance Setting 7.4.1 User Management Figure 25 Figure 26 Figure 27 There have three level of authority; they are admin/user/guest.
H Series IP Camera User Manual – with Pan/Tilt of CMOS authority, it can do any change to the settings. User account only can operate the IP camera, can’t do changes to the settings, and please refers to Figure 26. Guest account only can watch the video, can’t do any operation to the IP camera, and please refers to Figure 27. 7.4.2 Auto Capture Setting Figure 28 Please tick “save picture on the SD card”, the equipment will snapshot every short time (for example, showed as Figure 28, every 60 minutes) 7.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7.4.4 FTP Setting Figure 30 In order to use FTP function, user should apply username and password on the FTP server first. And please apply some storage, and the authority to write and create sub-category into it. 7.4.5 Alarm Server Setting Figure 31 Please confirm if you have connected to alarm server. The alarm message format as follow: GET /api/alarm.
H Series IP Camera User Manual – with Pan/Tilt of CMOS Figure 32 7.5.2 Default Setting Figure 33 Reboot button to restart the equipment, if you have set the pre-position, and it will turn this position. Click “Factory Default” button, equipment will restart and back to all the default settings. Click “save”, it will save all the present settings. “Restore” part, select the setting file you have saved, click OK, it will recover all the settings.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7.5.3 Device Information Checking Figure 34 Device ID is set by factory. Every ID is unique Network Connection status will display “LAN” when connected by wired cable and display “Wireless LAN” connected by wireless Router. SD status will remind if SD card inserted and display the free capacity. Click “Browse” to view the contents in SD card and, “Format SD Card as fat32” to format SD Card and, “Unplug SD Card” to stop the work of SD Card.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 7.5.5 User browsing Log Checking Figure 36 8 Advanced Application 8.1 Mobile phone Browsing The device can be visited via mobile phone when it is connected to internet. Below are the vi sit methods: 1) http://IP:Port/wap.wml, the “IP” is the WAN IP address of the IP Camera or domain name (third party domain name only), if HTTP port is 80, the “port” of 80 can be omitted. For examples: http://58.61.54.177:1025/wap.wml http://test.3322.org:1025/wap.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 8.2 Other web browser visit device Using browser with IE kernel, user must download the Activex. Using other web browser like Safari or Firefox, it will use QuickTime to play. Safari for example, you can find the player interface as the below Figure 37.
H Series IP Camera User Manual – with Pan/Tilt of CMOS In the Windows OS, if you don’t install the QuickTime, it will remind the users of installation. Users could install the QuickTime according to its message. After installation, users can start the QuickTime program, and to access the QuickTime Preferences dialog box from Edit Menu. Click Advanced, select “custom..” in the Transport Setup. It pops up the Streaming Transport dialog box.
H Series IP Camera User Manual – with Pan/Tilt of CMOS 9 Technical Parameters Item Sub item Description Sensor 1/4" CMOS sensor Image Total of pixel 300k Capture Minimum illumination IR lights on,0 Lux Lens f=4.5mm, F=2.0, Fixed Iris Pan Coverage 350° Tilt Coverage 100° Preset Numbers 1 Lighting Control Auto/manual control Lighting 8pcs 850nm Infrared lights, 5m distant Resolution VGA/QVGA/QQVGA Compression H.264 Frame rate 30fps Bit rate 128kbps ~ 2.
H Series IP Camera User Manual – with Pan/Tilt of CMOS Index Main body 111mm(L)*107mm(W)*121mm(H) Power DC 5V Power consumption <6W Operating temperature Humidity 10% ~ 80% non-condensing OS Supported Microsoft Windows 98/2000/XP/Vista, Mac OS Software(PC Side) 0℃~ 45℃ Browser Application Software Internet Explorer6.0 and Above or Compatible Browser, Safari/Firefox etc. IPCMonitor.