Installation Guide

ManualsBrandsVonn ManualsOutdoor Lighting32" Modern 100-277V 10-Watt Integrated LED Outdoor Bollard in Matt Black

INSTALLATION GUIDE

VONN LIGHTING MODEL#

VOB192208

LED INFO & WARNINGS

Please read and understand the entire manual

before attempting to assemble, operate, or install

the product.

VONN highly recommends using a qualiﬁed and

licensed electrician to install ﬁxture.

120V. Not dimmable.

All parts must be used as indicated in these

instructions. Do not substitute any parts, leave

parts out, or use any parts that are worn or broken.

Inspect the LED ﬁxture prior to installation to make

sure that it has not been damaged during shipping.

Please handle the LED light with care when

unpacking. Do not apply pressure to the LED’s, do

not open any factory sealed compartments, and do

not touch the LEDs with your hands.

Shut “OFF” the electricity at main fuse box.

Please use watertight box for electrical connections.

Do not remove or replace VONN manufactured

parts that are provided with the ﬁxture.

Place the electrical switch in the “OFF” position.

Make sure that you have all necessary parts by

checking the parts list. If any part is missing or

damaged please contact VONN LIGHITNG

CUSTOMER SERVICE at 888-604-8666 for

a replacement.

VONN recommends to install the ﬁxture on

its own independent circuit. Do not install the

ﬁxture on the same circuit with the other

appliances, or HVAC systems.

Attention: This VONN ﬁxture is not dimmable.

TOOLS YOU MAY NEED

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

www.vonn.com

PARTS LIST

CIRCUIT BOX

OFF

1 1

M6X80 Expansion Bolt, Pipe, Nut,

Lock Washer, Flat Washer. x4

Wire Cap. x4

Wrench. x1

Summary of content (12 pages)

PAGE 1
INSTALLATION GUIDE VONN LIGHTING MODEL# VOB192208 TOOLS YOU MAY NEED GOGGLES TAPE MEASURE PARTS LIST PHILLIPS SCREW DRIVER DRILL LADDER CIRCUIT BOX 1 1 M6X80 Expansion Bolt, Pipe, Nut, Lock Washer, Flat Washer. x4 2 2 Wire Cap. x4 3 Wrench. x1 3 RUBBER GLOVES OFF ON OFF LED INFO & WARNINGS LED INFO & WARNINGS Please read and understand the entire manual before attempting to assemble, operate, or install the product.
PAGE 2
Step 1 Turn off the power at the breaker box. Test the power is off at the wire connector box with a circuit tester. 8” (206 mm) Legend L = Live/Hot/Black N = Neutral/White 31.5” (800 mm) = Ground/Green 5”(120 mm) Component List 1 2 M6X80 Expansion Bolt Pipe Nut Lock washer Flat washer x 4 Wire Cap x4 7”(180mm) 3 VONN Lighting Model: VOB192208BL www.vonn.
PAGE 3
Step 2 Drill holes in the concrete floor and install the expansion pipes. Existing electrical connection n 6.3 i 4- ϕ8 3.9 in Concrete Floor Installation Hole Size Wire Connector Box www.vonn.
PAGE 4
Step 3 A. Place all high voltage wires in a water proof wire connector box. B. Connect the wires with wire caps, connect the Black wire from the light fixture to the live wire in your wire connector box. C. Connect the White wire from the light fixture to the neutral wire in the wire connector box. D. Connect the Green wire from the light fixture to the ground wire in the wire connector box. Legend L = Live/Hot/Black N = Neutral/White = Ground/Green 2 nn e Co Wir www.vonn.
PAGE 5
Step 4 Install the light fixture to concrete floor with provided expansion bolts, lock washers and flat washers. 1 M6x80 Expansion Bolt Lock washer Flat washer Wire Connector Box www.vonn.
PAGE 6
Step 5 Turn electricity “ON” at main fuse box. Circuit Box ON OFF www.vonn.
PAGE 7
GUIDE D’INSTALLATION : VONN LIGHTING MODÈLE N° VOB192208 OUTILS DONT VOUS POURRIEZ AVOIR BESOIN LUNETTES DE PROTECTION LISTE DES PIÈCES 1 2 3 MÈTRE RUBAN GANTS EN C AOUTCHOUC TOURNEVIS CRUCIFORME PERCEUSE ÉCHELLE BOÎTIER DE CIRCUIT ÉLECTRIQUE 1 Boulon de scellement M6X80, tuyau, écrou, Rondelle de blocage, rondelle plate.
PAGE 8
Étape n° 1 Coupez le courant au niveau du coffret à disjoncteurs. Testez le courant au niveau de la boîte de connexion des fils à l'aide d'un testeur de circuit. 8” (206 mm) Légende L = Vif/chaud/noir N = Neutre/blanc 31.5” (800 mm) = = Mise à la terre/vert Liste des composants 1 Boulon de scellement M6X80, tuyau, écrou Rondelle de blocage Rondelle plate x 4 5”(120 mm) 2 Muselet x4 7”(180mm) 3 VONN Lighting Modèle VOB192208BL www.vonn.
PAGE 9
Étape n° 2 Percez des trous dans le sol en béton et installez les tuyaux d'expansion. Connexion électrique existante n 6.3 i 4- ϕ8 3.9 in Plancher en béton Boîtier de connexion des fils www.vonn.
PAGE 10
Étape n° 3 A. Placez tous les fils haute tension dans un boîtier de connexion étanche. B. Connectez les fils avec des muselets, connectez le fil noir du luminaire au fil sous tension dans votre boîtier de connexion des fils. C. Connectez le fil blanc du luminaire au fil neutre dans votre boîtier de connexion des fils. D. Connectez le fil vert de l'appareil d'éclairage au fil de mise à la terre dans votre boîtier de connexion des fils.
PAGE 11
Étape n° 4 Installez le luminaire sur le plancher en béton à l'aide des boulons de scellement, des rondelles de blocage et des rondelles plates fournis. 1 M6x80 Boulon de scellement Rondelle de blocage Rondelle plate Boîtier de connexion des fils www.vonn.
PAGE 12
Étape n° 5 Rétablissez le courant au niveau du boitier à fusibles. Boîtier de circuit électrique ON OFF www.vonn.