VONETS - Wireless Module/Finished Product Wireless module/WiFi product VM300/VM5G/VBG1200/VAP11AC Quick Setting Guide
VONETS - Wireless Module/Finished Product Declaration Copyright © 2023 Shenzhen HouTian Network Communication Technology Co.,Ltd All rights reserved, with retained ownership Without Shenzhen HouTian Network communication Technology Co.,Ltd written authorization, any company or personal can’t copy, writer or translation part or all contents. Can’t do commodity distribution for any commercial or profitable purposes by any ways(electricity, mechanical, photoprint, record or othe r methods).
VONETS - Wireless Module/Finished Product Form2 Power Supply Parameters List Model VM300 VM5G/VBG1200 VAP11AC ≥5W Typical Power Supply 5V/1A ≥10W 5V/2A Power Supply Voltage Input Power DC5V--15V DC5V--15V DC5V--24V
VONETS - Wireless Module/Finished Product Contents Chapter 1 Application Mode ................................................................... 1 1.1 Bridge + Repeater Mode .............................................................................................................. 1 1.2 Router Mode ................................................................................................................................ 2 Chapter 2 Bridge+Repeater Mode Configuration Instruction ................
VONETS - Wireless Module/Finished Product Chapter 1 Application Mode 1.1 Bridge + Repeater Mode There are three application modes for the bridge mode of VONETS module/WiFi product: WiFi repeater, WiFi bridge and WiFi AP. ⚫ WiFi Repeater: VONETS module/WiFi product as WiFi Repeater, it must be configured to source WiFi hostpot parameters, can be used to extend the wireless signal coverage of existing APs or wifi router .
VONETS - Wireless Module/Finished Product 1.2 Router Mode ⚫ VONETS module/WiFi product as WiFi router The Ethernet port of VM300 module/ VAP11AC finished product defaults to WAN port. The Ethernet cable defaults to the LAN port. WAN and LAN ports are interchangeable. The Ethernet cable of VM5G module/VBG1200 WiFi product defaults to LAN port, you must set “WAN/LAN interchange” so that the Ethernet cable is WAN port to use the broadband dialing function.
VONETS - Wireless Module/Finished Product Chapter 2 Bridge+Repeater Mode Configuration Instruction 2.1 Method 1: Log in to the device's Web configuration page to configure 2.1.1 Device Connection Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are two connection ways as below: A. Computer is wired connected to LAN port of VONETS module/WiFi product; （Recommend Method） B.
VONETS - Wireless Module/Finished Product (After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.) 2.2 Bridge+Repeater Application Configuration The configuration steps of VONETS module/WiFi product for WiFi repeater and WiFi bridge are basically the same, so this manual combines the configuration instructions of the two application modes. 1. After computer is connected to VONETS module/WiFi product, open browser, input configured page: http://vonets.cfg (or IP: 192.168.
VONETS - Wireless Module/Finished Product 4. Input “Source wireless hotspot password”, click “Apply”; ⚫ IP layer transparent transmission (factory default), transparent transmission of IP layer data, can meet most of WiFi bridge applications; ⚫ MAC layer transparent transmission, transparent transmission of all data above the MAC layer (link layer) and MAC layer, including IP layer data.
VONETS - Wireless Module/Finished Product 5.
VONETS - Wireless Module/Finished Product Remark 1: LED Light Form Model Blue Light Green Light Yellow Light WiFi Connection Ethernet Cable VM300 / Status Light Connection Status Light WiFi Connection 5G WiFi Connection Ethernet Cable VM5G/VBG1200/VAP11AC Status Light Status Light Connection Status Light ① VONETS module/WiFi product is not connected to any hotspot, WiFi connection status light will flash quickly; ② VONETS module/WiFi product is connected to hotspot successfully, WiFi connection status ligh
VONETS - Wireless Module/Finished Product 3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in “Pass Phrase”, click “Apply”; 4.
VONETS - Wireless Module/Finished Product 5. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it is finished, all revised options will take effort. Remark 2: When VONETS module/WiFi product connect to external network, its IP address will be changed. At this time, when log in configured page, we suggest you enter configured domain name: http://vonets.cfg. Or in Windows command window, enter the command: ping vonets.
VONETS - Wireless Module/Finished Product （Recommend Method） B. Computer wirelessly connects to the WiFi signal of VONETS module/WiFi product, its default hotspot parameters are as follows: WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address) WiFi password: 12345678 (After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.) 2. After computer is connected to VONETS module/WiFi product, open browser, input configured page domain name: http://vonets.
VONETS - Wireless Module/Finished Product 4. In “Operating Mode”, change Device mode to “Router” mode, click “Apply” button; 5. Reboot device: go to “System Settings”-- “Reboot device”, click “Reboot” button, VONETS module/WiFi product will automatically switch to router mode. 3.2 WAN port setting 3.2.1 WAN/LAN exchange In routing mode, the Ethernet port of VONETS module/WiFi product is divided into a WAN port and a LAN port, and WAN/LAN can be interchanged.
VONETS - Wireless Module/Finished Product 3.2.2 WAN Port connection method By setting the WAN port of the router, you can change the network connection type according to the actual needs of the individual, there are three types of WAN port connections commonly used in the routing mode of the VONETS module/WiFi product: DHCP(Auto Config), PPPoE(ADSL) and WiFi.
VONETS - Wireless Module/Finished Product 3.2.4 WAN port wired connect network——PPPoE In “WAN settings”, select “Basic settings”, change the connection type to “PPPoE (ADSL)”, then enter the Internet account and password provided by the ISP (Internet Service Provider), click the “Apply” button, and then reboot VONETS module/WiFi product, then can access to network. 3.2.5 WAN port wireless connect network---- WiFi 1.
VONETS - Wireless Module/Finished Product 2. Choose the source hotspots, click “Next”; 3.
VONETS - Wireless Module/Finished Product 4. Click “Reboot”, VONETS module/WiFi product will connect to the configured WiFi hotspot automatically, if connection is successful, the WiFi LED light will flash quickly;(Please refer to Remark 1 for the description of the LED light.) Remark 3: After VONETS module/WiFi product sets the WAN port to access the WiFi hotspot in the routing mode, its LAN port IP is still 192.168.254.
VONETS - Wireless Module/Finished Product 2. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in “Pass Phrase”, click “Apply”; 3. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it is finished, all revised options will take effort.
VONETS - Wireless Module/Finished Product Appendix Frequently Asked Questions 1. How to restore the factory default parameters of the VONETS module/WiFi product? Please refer to the information below to reset the factory default parameters of the VONETS module/WiFi product： VM300: http://www.vonets.com/serviceView.asp?D_ID=213 VM5G: http://www.vonets.com/serviceView.
VONETS - Wireless Module/Finished Product ⚫ ⚫ ⚫ 5. Reason 3. The device WiFi doesn’t work at the best channel, make the performance worse. At this time, you can try to change the source WiFi hot spot WiFi channel to make it the same as the default channel of the device, the reboot the device, the device will automatically exchange to the same channel as the source WiFi hotspot, to make the performance better; Reason 4.
VONETS - Wireless Module/Finished Product FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
