DEAR VOLVO OWNER THANK YOU FOR CHOOSING VOLVO We hope that you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your passengers. Volvo is one of the safest cars in the world. Your Volvo has also been designed to satisfy all current safety and environmental requirements.
Contents 2 00 Introduction 01 Safety Introduction ........................................ 6 Volvo Cars and the environment......... 7 Seatbelts .......................................... Airbag system .................................. Airbags (SRS) ................................... Activating/deactivating the airbag (SRS) ............................... Side airbags (SIPS bags).................. Inflatable Curtain (IC) ....................... WHIPS..............................................
Contents 03 Climate control 04 Interior 05 Locks and alarm General information on climate control .............................................. Manual climate control, A/C............. Electronic climate control, ECC (option) ..................................... Air distribution .................................. Fuel-driven heater (option) ............... Front seats ........................................ 82 Interior lighting ..................................
Contents 4 06 Starting and driving 07 Wheels and tyres General ........................................... 110 Refuelling........................................ 112 Starting the engine ......................... 113 Ignition switch and steering lock.... 114 Keyless drive .................................. 115 Manual gearbox.............................. 116 Automatic gearbox ......................... 118 All-wheel drive ................................ 121 Brake system..................................
Contents 09 Maintenance and service 10 Infotainment system 11 Specifications Volvo service ................................... 176 Self-maintenance ........................... 177 Bonnet and engine compartment .. 178 Diesel.............................................. 179 Oils and fluids ................................ 180 Wiper blades .................................. 185 Battery........................................... 186 Replacing bulbs ............................. 188 Fuses ..................
Introduction Introduction Owner’s Manual A good way of getting to know your new car is to read the Owner’s Manual, ideally before your first journey. This will give you the opportunity to familiarise yourself with new functions, to see how best to handle the car in different situations, and to make the best use of all the car’s features.
Introduction Volvo Cars and the environment Volvo Cars’ environmental philosophy Environmental care, safety and quality are the three core values which influence all operations of the Volvo Car Corporation. We also believe that our customers share our consideration for the environment. EPI (Environmental Product Information) is supplied for all Volvo models. You can now compare the environmental impact of different models and engines during the entire lifecycle.
Introduction Volvo Cars and the environment Efficient emission control Your Volvo is manufactured following the concept Clean inside and out – a concept that encompasses a clean interior environment as well as highly efficient emission control. In many cases the exhaust emissions are well below the applicable standards. In addition there is a special radiator coating, PremAir®1, which can convert hazardous ground-level ozone into pure oxygen when the ozone passes the radiator.
Introduction Volvo Cars and the environment Reducing environmental impact You can help reduce environmental impact, for example, by driving economically, by purchasing eco-labelled car care products and by servicing and maintaining the car according to the instructions in the Owner’s Manual. The following hints will help you to do your bit for the environment: • Decrease fuel consumption by choosing ECO tyre pressure, see page 152.
Seatbelts .................................................................................................. Airbag system .......................................................................................... Airbags (SRS) ........................................................................................... Activating/deactivating the airbag (SRS) ....................................................................................... Side airbags (SIPS bags) ......................................
SAFETY 01
01 Safety 01 Seatbelts Always use a seatbelt feed the belt in by hand so that it does not hang lose. WARNING Each belt is intended for one person only. The belt locks and cannot be withdrawn • if it is pulled out too quickly • during braking and acceleration • if the car leans heavily. It is important that the belt lies against the body so it can provide maximum protection. Do not lean the backrest too far back. The seatbelt is designed to protect in a normal seating position. Tensioning the hip strap.
01 Safety Seatbelts Seatbelt reminder Unbelted occupants will be reminded to fasten their seatbelts through an audio and visual reminder. The audio reminder is speed-dependent. The visual reminder is located in the roof console and the combined instrument panel. At low speed, the audio reminder will sound for the first six seconds. Child seats are not covered by the seatbelt reminder system.
01 Safety 01 Seatbelts the vehicle as they drive (which means they must be able to easily operate the foot pedals and steering wheel). Within this context, they should strive to position the seat with as large a distance as possible between their abdomen and the steering wheel. Seatbelt tensioner Label on seatbelts with seatbelt tensioner. 14 All the seatbelts (except the centre rear belt) are equipped with belt tensioners.
01 Safety Airbag system Warning symbol on the combined instrument panel 01 As well as the warning symbol, a message may appear on the information display in appropriate cases. If the warning symbol malfunctions, the warning triangle illuminates and the message SRS AIRBAG SERVICE REQUIRED or SRS AIRBAG SERVICE URGENT appears in the information display. Contact an authorised Volvo workshop urgently. WARNING The airbag system1 is continually monitored by the system control module.
01 Safety 01 Airbags (SRS) Airbag (SRS) on the driver’s side Passenger airbag (SRS) WARNING To minimise the risk of injury if the airbag deploys, passengers must sit as upright as possible with their feet on the floor and backs against the backrest. Seatbelts must be secured. WARNING The car has an SRS airbag (Supplemental Restraint System) in the steering wheel to supplement the protection afforded by the seatbelt. This airbag is fitted into the centre of the steering wheel.
01 Safety Airbags (SRS) SRS system 01 NOTE The sensors react differently depending on the course of the collision and whether the seatbelts on the driver and passenger side are used. It is therefore possible that only one (or none) of the airbags may inflate in a collision. The SRS system senses the force of the collision on the car and adapts accordingly so that one or more airbags is deployed. NOTE SRS system, left-hand drive. The system consists of airbags and sensors.
01 Safety 01 Airbags (SRS) Location of the passenger airbag in left-hand drive and right-hand drive cars WARNING Never interfere with SRS components in the steering wheel or the panel above the glovebox. Objects and accessories must not be positioned or glued on or near the SRS AIRBAG panel (above the glovebox) or in the area affected by a deployed airbag.
01 Safety Activating/deactivating the airbag (SRS) PACOS (option) Activating/deactivating 01 WARNING Activated airbag (passenger seat): Never place a child in a child seat or on a booster cushion on the front passenger seat when the airbag is activated. This applies to everyone shorter than 140 cm. Deactivated airbag (passenger seat): No one taller than 140 cm should ever sit in the front passenger seat when the airbag is deactivated. Failure to follow the advice given above can endanger life.
01 Safety 01 Activating/deactivating the airbag (SRS) Switch position Switch for SRS in ON position. Switch for SRS in OFF position. ON = Airbag (SRS) activated. With the switch in this position, persons taller than 140 cm can sit in the front passenger seat, but never children in a child seat or on a booster cushion. OFF = Airbag (SRS) is deactivated.
01 Safety Side airbags (SIPS bags) Side airbags – SIPS bags 01 WARNING Do not put objects in the area between the outside of the seat and the door panel, since this area is required by the side airbag. WARNING Use only Volvo genuine car seat covers, or seat covers approved by Volvo. Other seat covers may impede the operation of the side air bags. Child seats and side airbags Side airbag locations.
01 Safety 01 Side airbags (SIPS bags) SIPS bags Driver’s side The SIPS bag system consists of side airbags and sensors. A sufficiently violent collision trips the sensors and the side airbags are inflated. The airbag inflates between the occupant and the door panel and thereby cushions the initial impact while deflating. The side airbag is normally only deployed on the side of the collision.
01 Safety Inflatable Curtain (IC) 01 Properties The inflatable curtain, IC (Inflatable Curtain), is a supplement to the SIPS system. It is fitted in the headlining along both sides of the roof and protects both front and rear seat passengers. The inflatable curtain is activated by sensors in the event of a sufficiently violent collision and the inflatable curtain inflates.
01 Safety 01 WHIPS Protection against whiplash injury – WHIPS The whiplash protection system (WHIPS) consists of energy absorbing backrests and specially designed head restraints for the front seats. The system is actuated by a rearend collision, where the angle and speed of the collision, and the nature of the colliding vehicle all have an influence.
01 Safety WHIPS Do not obstruct the WHIPS system 01 WARNING If a seat has been subjected to extreme forces, such as due to a rear-end collision, the WHIPS system must be checked by an authorised Volvo workshop. Part of the WHIPS system’s protective capacity may have been lost even if the seat appears to be undamaged. Contact an authorised Volvo workshop to have the system checked after even a minor rear-end collision.
01 Safety 01 When the systems deploy System Triggered Seatbelt tensioner In a frontal collision and/or side-impact accident and/or overturning. Airbags (SRS) In a frontal collision1. Side airbags (SIPS) In a side-impact accident1. Inflatable Curtain IC In a side-impact accident1. Whiplash protection WHIPS In a rear-end collision. 1 The bodywork of the car could be greatly deformed in a collision without airbag deployment.
01 Safety Crash mode Driving after a collision If everything seems normal and you have checked for indications of fuel leakage, you may attempt to start the car. Firstly, remove the ignition key and then reinsert it. The car’s electronics will then try to reset themselves to normal mode. Then try to start the car. If CRASH MODE is still shown in the display then the car must not be driven or towed. Even if the car appears to be driveable, hidden damage may make the car impossible to control once moving.
01 Safety 01 Child safety Children should sit comfortably and safely Child seats and airbags The position of a child in the car and the choice of equipment is dictated by the child’s weight and size. For more information see page 30. NOTE Regulations regarding the placement of children in cars vary from country to country. Check what laws apply. Children of all ages and sizes must always sit correctly secured in the car. Never allow a child to sit on the knee of a passenger.
01 Safety Child safety Decal located on instrument panel end face. 01 Decal located on instrument panel end face (Australia only).
01 Safety 01 Child safety Placement of children in the car Weight/age Front seat1 Outer rear seat Centre rear seat <10 kg (0–9 months) Rear-facing child seat, secured with seatbelt and straps. Use a protective cushion between the child seat and the dashboard. L2: Type approval no. E5 03135 Rear-facing child seat, secured with seatbelt, support legs and straps. L2: Type approval no. E5 03135 Rear-facing child seat, secured with seatbelt, support legs and straps. L2: Type approval no.
01 Safety Child safety Integrated booster cushion (option) 01 Raising the booster cushion WARNING Never place a child in a child seat or on a booster cushion in the front seat if the airbag (SRS) is activated. No one shorter than 140 cm should ever sit in the front passenger seat if the airbag (SRS) is activated.1 Failure to follow the advice given above can endanger the life of the child. 1 For information on activated/deactivated airbag (SRS), see page 19.
01 Safety 01 Child safety the belt is positioned correctly across the shoulder. • the hip strap is low across the hips for optimum protection. • the seatbelt does not lie across the child’s throat or below the shoulder • carefully adjust the position of the head restraint to suit the child. Lowering the booster cushion WARNING Repair or replacement should only be performed by an authorised Volvo workshop. Do not make any modifications or additions to the booster cushion.
01 Safety Child safety Fitting a child seat ISOFIX fixture system for child seats (option) Volvo has child safety products that are designed for and tested by Volvo. WARNING Booster cushions/child seats with steel braces or some other design that could rest on the seatbelt buckle’s opening button must not be used, as they could cause the seatbelt buckle to open accidentally. Do not allow the upper section of the child seat to rest against the windscreen.
Overview, left-hand drive cars.................................................................. Overview, right-hand drive cars ............................................................... Driver’s door control panel....................................................................... Combined instrument panel..................................................................... Indicator and warning symbols ................................................................ Information display...........
INSTRUMENTS AND CONTROLS 02
02 Instruments and controls Overview, left-hand drive cars 02 36
02 Instruments and controls Overview, left-hand drive cars 1. Steering wheel adjustment 2. Bonnet release 3. Control panel 4. Direction indicators, main beam, trip computer 5. Lighting, fuel filler flap opener 6. Door handle, lock button. 7. Air vents in dashboard 8. Air vent for side window 9. Cruise control 10. Horn, airbag 11. Combined instrument panel 12. Keypad for infotainment system 13. Windscreen wipers and washer, headlamp washers 14. Ignition switch 15. Sunroof controls 16. No function 17.
02 Instruments and controls Overview, right-hand drive cars 02 38
02 Instruments and controls Overview, right-hand drive cars 1. Switch, optional equipment 2. Blind Spot Information System, BLIS 3. Electrical socket, cigarette lighter 4. Parking brake 5. Control panel 6. Glovebox 7. Door handle 8. Air vent for side window 9. Air vents in dashboard 10. Gear lever 11. Climate control 12. Controls for climate control, infotainment system and personal preferences 13. Infotainment system 14. Display for climate control and infotainment system 15. Interior rearview mirror 16.
02 Instruments and controls Driver’s door control panel Driver’s door control panel 02 1. Blocking switch for rear power windows (standard) Electric child locks (option) 2. Power windows 3. Door mirror, left-hand side 4. Door mirrors, setting 5.
02 Instruments and controls Combined instrument panel 02 1. 2. 3. 4. Speedometer. Direction indicators, left. Warning symbol. Information display – The display presents information and warning messages, outside temperature and the time. When the ambient temperature is between +2 °C and –5 °C, a snowflake symbol appears on the display. This warns of icy roads. The outside temperature gauge may show a slightly high reading after the car has been stationary. 5. Information symbol. 6.
02 Instruments and controls Indicator and warning symbols Functionality check, symbols 02 All indicator and warning symbols1 illuminate when the ignition key is turned to position II before starting. This is to check that the symbols are working. When the engine starts, all the symbols should go out except the handbrake symbol, which extinguishes when the handbrake is released.
02 Instruments and controls Indicator and warning symbols Indicator symbols – left-hand side – Drive to an authorised Volvo workshop to have the ABS checked if the symbol remains lit. 02 3. Rear fog lamp This symbol is lit when the rear fog lamp is on. 4. Stability system STC or DSTC For information on the system’s functions and symbols, see page 124. 5. No function 1. Fault in car’s emissions system Drive to an authorised Volvo workshop to have the system checked. 2.
02 Instruments and controls Indicator and warning symbols Indicator symbols – right-hand side 02 2. Parking brake applied The lamp comes on when the parking brake is applied. Always pull the parking brake lever to the end position. NOTE The lamp illuminates irrespective of how hard the parking brake is applied. 1. Indicator symbol for trailer This symbol flashes when the direction indicators are used and a trailer is coupled.
02 Instruments and controls Indicator and warning symbols • Stop the car in a safe place and turn off the engine. • Restart the engine. • If both symbols extinguish, continue driving. • If the symbols remain on, check the level in the brake fluid reservoir. See page 183. • If the brake fluid level is normal but the symbols are still lit, the car can be driven, with great care, to an authorised Volvo workshop to have the brake system checked.
02 Instruments and controls Information display Messages 02 When a warning or indicator symbol come, a message appears on the information display. – Press the READ button (1). Switch between messages with the READ button. Fault messages are stored in the memory until the fault is rectified. NOTE If a warning message appears while you are using the trip computer, the message must be read (press READ) before the previous activity can be resumed.
02 Instruments and controls Electrical socket and switches on centre console 12 V electrical socket Cigarette lighter (option) Activate the lighter by pushing in the button. The button pops out when the lighter is hot. Pull out the lighter and light a cigarette on the heated coils. 02 Extra equipment Space for an extra switch for retrofitted equipment. Electrical socket, BLIS and extra equipment The electrical socket can be used for 12 V accessories, such as mobile phone chargers and coolers.
02 Instruments and controls Lighting panel Headlamp levelling The load in the car changes the vertical alignment of the headlamp beam, which could dazzle oncoming motorists. Avoid this by adjusting the height of the beam. 02 – Turn the ignition key to position II. – Turn the headlamp control (2) to one of the end positions. – Roll the control (1) up or down respectively to raise or lower beam alignment. Cars with Bi-Xenon headlamps1 have automatic headlamp levelling, so there is no control (1).
02 Instruments and controls Lighting panel the day and can be controlled manually at night. – Roll the control up or down (3) for brighter or dimmer lighting. Enhanced display lighting To facilitate reading the odometer, trip meter, clock and outside temperature gauge, these illuminate when the car is unlocked and when the key is removed from the ignition switch. The displays extinguish when the car is locked.
02 Instruments and controls Left-hand stalk switch Stalk switch positions 02 Short flash sequence – Move the stalk switch up or down to position (1) and release. The direction indicators flash three times and the stalk switch returns to its home position. Switching, main and dipped beam The ignition key must be in position II for main beam to be switched on. – Turn the headlamp control clockwise to the end position, see page 48.
02 Instruments and controls Left-hand stalk switch Trip computer (option) Functions The trip computer displays the following information: • • • • • • AVERAGE SPEED ACTUAL SPEED MPH1 NOTE If a warning message interrupts while you are using the trip computer, this message must be acknowledged. Acknowledge by pressing the READ button (A) and revert to the trip computer function. AVERAGE KILOMETRES TO EMPTY TANK STC/DSTC, see page 124 ACTUAL SPEED MPH1 Current speed is displayed in mph.
02 Instruments and controls Right-hand stalk switch Windscreen wipers 02 Single sweep Raise the stalk switch to make a single sweep. Intermittent wiping The delay between sweeps can be adjusted. Turn the thumbwheel (C) up for a shorter interval between sweeps. Turn it down to increase the delay. Continuous wiping The wipers sweep at normal speed. A. Windscreen and headlamp washers The wipers sweep at high speed. B. Rain sensor – On/Off C. Thumbwheel D.
02 Instruments and controls Right-hand stalk switch Rain sensor (option) Activating the rain sensor: – Press the button (B). A display symbol shows that the rain sensor is active. To turn the rain sensor off, either: The rain sensor automatically activates the windscreen wipers based on how much water it detects on the windscreen. The sensitivity of the rain sensor can be adjusted using the thumbwheel (C). Turn the thumbwheel clockwise for higher sensitivity and anticlockwise for lower sensitivity.
02 Instruments and controls Cruise control (option) Activating Increasing or decreasing speed – Press 0 to disengage the cruise control temporarily. CRUISE will be shown on the combined instrument panel. The speed set earlier is stored in the memory. The cruise control is also temporarily disengaged when: 02 The controls for cruise control are to the left of the steering wheel. Setting the desired speed: – Press the CRUISE button. CRUISE is shown on the combined instrument panel.
02 Instruments and controls Steering wheel keypad (option) Button functions 02 The four buttons at the bottom of the steering wheel keypad control the radio and the phone. The function of a button depends on which system is active. The steering wheel keypad can be used to scroll between preset stations, change CD tracks and adjust the volume. – Press and hold one of the arrow keys to fast forward/reverse or search for the next station. The phone must be switched on to adjust audio system settings.
02 Instruments and controls Steering wheel adjustment, hazard warning flashers Steering wheel adjustment Hazard warning flashers The steering wheel can be adjusted for both height and reach. Use the hazard warning flashers (all direction indicators flash) when the car is stopped where it could be a traffic hazard or obstruction. Press the button to activate the function. 02 – Pull the lever towards you to release the steering wheel. – Adjust the steering wheel to the position that suits you best.
02 Instruments and controls Parking brake, electrical socket Parking brake (handbrake) – If the vehicle rolls, the parking brake lever must be pulled more firmly. When parking a vehicle always put the gear selector in 1st gear (for manual transmission) or P (for automatic transmission). Electrical socket in the rear seat 02 Parking on a hill If the car is parked facing uphill; turn the wheels away from the kerb. If the car is parked facing downhill; turn the wheels toward the kerb.
02 Instruments and controls Power windows Operation 02 Driver’s door The power windows are operated using the controls in the doors. The ignition key must be in position I and II for the power windows to operate. The windows continue to work for a limited time when the car is stationary and ignition key is removed, provided none of the doors is opened. Operate the windows with caution. will then open or close automatically. If the window is obstructed by an object, the movement will stop.
02 Instruments and controls Power windows Blocking power windows in the rear doors Rear power windows NOTE 02 If the car has electric child safety locks on the rear doors, the light indicates that these are activated. The doors then cannot be opened from the inside. A text message is shown on the display when the electric child safety locks are activated. Front passenger seat The rear door windows can be operated with the control on each door or with the switch on the driver’s door.
02 Instruments and controls Rearview and door mirrors Interior rearview mirror Rearview mirror with compass (option on certain markets) Calibrating the compass 02 The illustration is a montage. The mirror has either manual dipping or automatic dimming. Bright light from behind could be reflected in the rearview mirror and dazzle the driver. Dipping 1. Control for dimming 2. Normal position 3. Dimmed position.
02 Instruments and controls Rearview and door mirrors – Press the button (1) repeatedly until the number for the required magnetic zone (1– 15 ) is shown, refer to the map of magnetic zones for the compass. – Wait until the display returns to showing the character C. – Following which, press and hold the button for 9 seconds and select L for lefthand drive cars and R for right-hand drive.
02 Instruments and controls Rearview and door mirrors Door mirrors 02 Retractable power door mirrors (option) The mirrors can be retracted for parking and driving in narrow spaces. This can be done in ignition position I and II. Retracting the mirrors – Press the L and R button at the same time. – Release the buttons. The mirrors automatically stop in the fully retracted position. IMPORTANT The controls for adjusting the two door mirrors are at the front of the driver’s door armrest.
02 Instruments and controls Rearview and door mirrors Water and dirt-repellent coating (option) The door mirrors are treated with a coating that maintains good rear-view vision despite the rain. 02 The mirrors treated with the water and dirt-repellent coating are marked with a small symbol. For information on how the mirrors should be maintained, see page 169. In certain weather conditions, the function of the dirt-repellent coating is improved if the door mirror defrosters are used, see page 73.
02 Instruments and controls Power sunroof (option) Open positions From ventilation position to fully open sunroof: 02 – Pull the control rearward to the end position (1) and release. Sliding position Automatic operation – Pull the control past the point of resistance (2) to the rear end position (1) or past the point of resistance (3) to the forward end position (4) and release. The sunroof opens/closes completely. Manual operation The sunroof controls are located in the roof panel.
02 Instruments and controls Power sunroof (option) Closing with remote control or lock button Sunscreen The sunroof features a manual, sliding interior sunscreen. The sunscreen slides back automatically when the sunroof is opened. Grip the handle and slide the screen forwards to close it. 02 Pinch protection The sunroof’s pinch protection function is activated if the hatch is blocked by an object. If blocked, the sunroof will stop and automatically open to the previous position.
02 Instruments and controls Personal preferences 02 Possible settings Climate control settings Personal preferences can be set for some of the car’s functions: the locks, climate control and audio functions. For audio functions, see page 204. Automatic fan adjustment The fan speed can be set to AUTO mode in cars equipped with ECC: Control panel A. Display B. MENU C. EXIT D. ENTER E. Navigation Use The settings are shown on the display (A).
02 Instruments and controls Personal preferences remote control. This function can be turned On or Off. Automatic locking – doors When the speed of the car exceeds 7 km/h the doors and tailgate can be locked automatically. This function can be turned On/ Off. Pulling the door handle twice unlocks and opens the doors from the inside. Unlock doors There are two alternatives for unlocking: • All doors – one press of the remote control unlocks both doors and the tailgate.
General information on climate control ...................................................................................................... Manual climate control, A/C..................................................................... Electronic climate control, ECC (option)............................................................................................. Air distribution .......................................................................................... Fuel-driven heater (option) ...
CLIMATE CONTROL 03
03 Climate control General information on climate control Air conditioning The climate control system cools or heats, and dehumidifies the air entering the passenger compartment. The car is equipped with either manual (A/C) or electronic climate control (ECC). 03 NOTE The air conditioning system can be switched off, but to ensure the best possible air in the passenger compartment and prevent the windows from misting, it should always be on.
03 Climate control General information on climate control ECC (option) Actual temperature The temperature you select corresponds to the physical experience with reference to factors such as air speed, humidity and solar radiation in and around the car. Sensor location • The sun sensor is on the top side of the dashboard. • The temperature sensor for the passenger compartment is behind the climate control panel.
03 Climate control Manual climate control, A/C Control panel 03 1. 2. 3. 4. 5. 6. 7. 8. Fan Recirculation Defroster Air distribution AC ON/OFF Heated front left seat Heated front right seat Rear window and door mirror defrosters 9. Temperature 72 Functions 1. Fan Increase or decrease the fan speed by turning the knob. If the knob is turned anticlockwise and the fan indicator in the display goes out, the fan and the air conditioning are switched off. The display shows the fan symbol and OFF. 2.
03 Climate control Manual climate control, A/C Timer The timer function minimises the risk of icing, misting and bad air if recirculation is selected. See page 66, for how to activate/deactivate the function. When the Defroster (3) program is selected, recirculation is deactivated. 4. Air distribution The airflow can be distributed to the windows, dashboard vents or floor by pressing the air distribution buttons. 3.
03 Climate control Electronic climate control, ECC (option) Control panel 03 1. 2. 3. 4. 5. 6. 7. 8. 9. AUTO Fan Recirculation/Air quality system Defroster Air distribution A/C ON/OFF Heated front left seat Heated front right seat Rear window and door mirror defrosters 10. Temperature selector 74 Functions 2. Fan Increase or decrease fan speed by turning the knob. The fan speed is regulated automatically if AUTO is selected, and the previously set fan speed is disengaged. 1.
03 Climate control Electronic climate control, ECC (option) 3. Recirculation Recirculation can be used to shut out bad air, exhaust fumes, etc. from the passenger compartment. The air in the passenger compartment is recirculated, i.e. no outside air is taken into the car when this function is activated. If the air in the car recirculates for too long, there is a risk of misting on the insides of the windows.
03 Climate control Electronic climate control, ECC (option) illuminated light in the relevant button indicate which function has been selected. See the table on page 77. 03 6. AC – ON/OFF ON: Air conditioning is on. It is controlled by the system’s AUTO function. This way, incoming air is cooled and dehumidified. OFF: Off. When the defroster function is activated the air conditioning is automatically switched on (can be switched off with the A/C button). 7. and 8.
03 Climate control Air distribution Air distribution Use: Air distribution Use: Air to windows. Some air flows to the dashboard air vents. The air is not recirculated. Air conditioning is always engaged. To remove ice and misting quickly. Air to the floor and windows. Some air flows to the dashboard air vents. To ensure comfortable conditions and good demisting in cold or humid weather. Air to windscreen and side windows. Some air flows to the dashboard air vents.
03 Climate control Fuel-driven heater (option) General information about heaters 03 Parking on a hill If the car is parked on a steep hill, the front of the car should point downhill to ensure that there is a supply of fuel to the parking heater. WARNING The car must be outdoors when the petrol or diesel heater is used. WARNING Switch off the fuel-driven heater before refuelling. Spilled fuel could be ignited. Check on the information display that the heater is off.
03 Climate control Fuel-driven heater (option) Immediate stop of heater Setting the TIMER AM and PM Clock/timer – Use the thumbwheel (B) to scroll to DIRECT START. – Press RESET (C) to access the options ON and OFF. – Select OFF. For safety reasons, you can only programme times for the following 24 hours, not several days in advance. If the car clock is reset after the heater timers are programmed, the selected times will be cancelled. – Scroll with the thumbwheel to TIMER.
Front seats ............................................................................................... 82 Interior lighting ......................................................................................... 84 Storage spaces in the passenger compartment...................................... 86 Rear seat .................................................................................................. 88 Cargo area...................................................................................
INTERIOR 04
04 Interior Front seats Seating position 4. Lumbar support1, turn the wheel, (option on passenger side) 5. Adjust backrest rake, turn the wheel. 6. Lever for power seat (option). WARNING Adjust the position of the driver’s seat before setting off, never while driving. Check that the seat is locked in position. 04 Lowering the front seat backrest (option) The passenger seat backrest can be folded forward to make room for long loads.
04 Interior Front seats Power seat (option) Memory function Emergency stop If the seat accidentally begins to move, press any of the buttons to stop the function. WARNING Risk of crushing. Make sure that children do not play with the controls. Check that there are no objects in front of, behind or under the seat during adjustment. Ensure that none of the rear seat passengers can be trapped.
04 Interior Interior lighting Reading lamps and interior lighting Automatic lighting The passenger compartment lighting is switched on and off automatically when button (2) is in neutral position.
04 Interior Interior lighting Vanity mirror1 04 The light comes on automatically when the cover is lifted. 1 Option on certain markets.
04 Interior Storage spaces in the passenger compartment 04 86
04 Interior Storage spaces in the passenger compartment Storage spaces Glovebox 1. Storage pocket (also on the front edge of the front seat cushions). 2. Compartment in door panel. 3. Ticket clip. 4. Coat hanger, only for light garments. 5. Glovebox. 6. Waste bin (accessory). 7. Storage compartment (e.g. for CD discs) and cup holder1. 8. Bottle holder (option). 9. Storage compartment and cup holder.
04 Interior Rear seat Head restraint, rear Tipping the rear seat backrest The rear seat backrests can be tipped forwards together, or individually, to make it easier to transport long objects. To avoid damaging the seatbelts when folding the backrests up or down, these should be hooked onto the grab handles. NOTE When tipping the rear seat the safety plug for the 12 V socket should be removed and placed in the glovebox to avoid pressure marks in the upholstery.
04 Interior Rear seat Bottle holder (option) NOTE When the backrest has been raised, the red indicator should no longer be showing. If it is, the backrest is not locked in place. WARNING Remember to take down the seatbelts once you have raised the backrest. Lowering the backrest – Pull the lock (2) catch up and forward to release the backrest. A red indicator on the lock catch shows that the backrest is no longer locked in place.
04 Interior Cargo area Load retaining eyelets Electrical socket in cargo area (option) Bag holder (option) 04 The load retaining eyelets are used to fasten straps or nets to anchor items in the cargo area. 90 Fold down the cover to access the electrical socket. This socket works regardless of whether the ignition is on. If the ignition is switched off and an appliance requiring a current greater than 0.1 A is plugged into the electrical socket, a warning message appears on the information display.
04 Interior 04 91
Remote control with key blade ................................................................ 94 Keyless drive (option) ............................................................................... 98 Locking and unlocking ........................................................................... 101 Child safety locks ................................................................................... 104 Alarm (option).....................................................................................
LOCKS AND ALARM 05
05 Locks and alarm Remote control with key blade Remote control Loss of a remote control The car is supplied with two remote controls which also serve as ignition keys. The remote controls contain detachable metal key blades for mechanical locking/unlocking of the driver’s door and glovebox. If you lose a remote control, take the car and the other remote controls to an authorised Volvo workshop. The code of the missing remote control must be erased from the system as a theft prevention measure.
05 Locks and alarm Remote control with key blade 4. Boot lid – Press the button once to unlock the boot lid only. NOTE The function does not open the boot lid. Use the remote control’s detachable key blade to block access to the glovebox and cargo area1. This means that the remote control can only open the doors and that the car can be driven. NOTE 5. Panic function — Used to attract attention in an emergency.
05 Locks and alarm Remote control with key blade Key blade 05 1. Active locks for remote control, without service locking activated. 2. Active locks for remote control, with service locking activated. Service locking1 Service locking: turn the key blade 180 degrees clockwise. This also means that the boot lid is blocked against opening with the remote control (a message is shown in the information display). For information on normal locking of the glovebox, see page 102.
05 Locks and alarm Remote control with key blade Weak remote control battery Replacing the remote control battery When the battery runs down and full functionality cannot be guaranteed, the information symbol and REMOTE BATTERY LOW VOLTAGE appear on the display. – Refit the cover and screw it shut. – Press the key blade back into place. Dispose of the old battery in an environmentally-friendly way.
05 Locks and alarm Keyless drive (option) Keyless lock and ignition system 05 98 The keyless drive system allows the car to be unlocked, driven and locked without the need for a key. You simply need to have the remote control with you in a pocket or a bag. Remote control max. 1.5 m from the car In order to open a door or the boot lid, a remote control must be no more than approx. 1.5 m from the car door handle or boot lid.
05 Locks and alarm Keyless drive (option) • the ignition dial has been turned to position 0 • the READ button has been pressed. Unlocking Never leave any remote control in the car If a remote control with keyless drive function is left in the car, it is made passive when the car is locked. This prevents unauthorised entry. – Open the doors by pulling the relevant handle. – Open the boot lid by pressing under the boot lid opening button and lift the boot lid.
05 Locks and alarm Keyless drive (option) Locking Lock the doors and boot lid as follows: – Push in the lock button on one of the door handles. All doors and the boot lid must be closed before the lock button is pushed in. Otherwise they will not lock. When the car is locked, the lock buttons on the inside of the doors retract. Personal preferences The Keyless Drive system can have personal preferences applied, see page 67.
05 Locks and alarm Locking and unlocking Locking/unlocking the car from outside Unlocking The remote control unlock button can unlock the car in two different ways (select option in personal preferences, see page 67): WARNING Be aware that you can be locked in the car if it is locked from the outside with the remote control. You cannot leave the car using any of the controls inside the car.
05 Locks and alarm Locking and unlocking Locking/unlocking the car from inside All the doors can be locked using the respective lock button. Locking the glovebox Opening the doors When the doors are locked from the inside: – Pull the handle twice to unlock and open the doors. 05 The doors and the boot lid can be locked or unlocked simultaneously using the lock button by the door handle. The glovebox can only be locked and unlocked with the removable key blade in the remote control.
05 Locks and alarm Locking and unlocking Deadlocks If the car is equipped with an alarm, movement and tilt detectors are also deactivated. See page 106. When deadlocked, the doors cannot be opened from the inside if they are locked. The deadlocks are activated with the remote control. The deadlocks are set after a 25 second delay after the doors are locked. The light in the button illuminates until the car is locked with the key or the remote control.
05 Locks and alarm Child safety locks Manual child locks in the rear doors Electric child safety locks and disabling the rear window buttons (option) Press the switch on the driver’s door. A message appears on the information display. To activate the child safety locks: – Turn the ignition key to position I or II. – Press the button. When the light in the button illuminates, the rear power windows and rear doors are locked.
05 Locks and alarm Alarm (option) Alarm system Alarm light on instrument panel When the alarm is armed, it continually monitors all alarm inputs.
05 Locks and alarm Alarm (option) Automatic alarm activation This function prevents you accidentally leaving the car without the alarm on. If none of the doors or the boot lid are opened within two minutes of disarming the alarm (and the car has been unlocked with the remote control), the alarm is automatically rearmed, and the car is locked at the same time. – Open the driver’s door with the key blade. The alarm is triggered and the siren sounds. – Insert the remote control into the ignition switch.
05 Locks and alarm Alarm (option) Testing the alarm system Testing the movement detector in the passenger compartment – Open all the windows. – Arm the alarm. Arming the alarm is confirmed by the light flashing slowly. – Wait 30 seconds. – Test the movement detector in the passenger compartment, such as by lifting out a bag from a seat. A siren should sound and all direction indicators should flash. – Deactivate the alarm by unlocking the car with the remote control. – Arm the alarm.
General................................................................................................... 110 Refuelling ............................................................................................... 112 Starting the engine................................................................................. 113 Ignition switch and steering lock............................................................ 114 Keyless drive .........................................................................
STARTING AND DRIVING 06
06 Starting and driving General Economical driving Driving economically means driving smoothly while thinking ahead and adjusting your driving style and speed to the prevailing conditions. 06 • Get the engine warmed up as soon as possible. • Do not let the engine idle, but drive at light loads as soon as it is possible. • A cold engine consumes more fuel than a warm one. • Avoid braking too hard. • Do not drive with unnecessary loads in the car. • Do not use winter tyres when the roads are dry.
06 Starting and driving General Clean the electric contacts of the electric engine block heater and trailer coupling after driving in water and mud. IMPORTANT Do not let the car stand with water over the sills for any long period of time. This could cause electrical malfunctions. In the event of stalling in water, do not try to restart. Tow the car out of the water. Do not overload the battery The electrical functions in the car load the battery to varying degrees.
06 Starting and driving Refuelling Opening the fuel filler flap – Take out the cap. 3. Hang up the cap on the inside of the fuel filler flap. NOTE Put the petrol cap back after refuelling. Turn until one or more clear clicks are heard. Filling up with fuel Do not overfill the tank but fill until the pump nozzle cuts out. NOTE Switch off the fuel-driven heater before refuelling. 06 Open the fuel filler flap with the button on the lighting panel, see page 49.
06 Starting and driving Starting the engine Before starting the engine Starting the engine – Apply the parking brake. Automatic gearbox – Gear selector in position P or N. Manual gearbox Put the gear lever in neutral and hold the clutch pedal fully depressed. This is particularly important in very cold conditions. WARNING Never remove the ignition key from the steering lock while driving or when the car is being towed.
06 Starting and driving Ignition switch and steering lock symbol on the dashboard illuminates, and the message SOOT FILTER FULL SEE MANUAL is shown on the dashboard display. Start regeneration of the filter by driving the car until the engine reaches normal operating temperature, preferably on a main road or motorway. The car should then be driven for approximately 20 minutes more. When regeneration is complete the message is cleared automatically.
06 Starting and driving Keyless drive General Starting the car Starting with the remote control – Depress the clutch pedal (cars with manual gearbox) or brake pedal (cars with automatic gearbox). Petrol engine – Press in and turn the ignition dial to position III. Diesel engine – First turn the ignition dial to position II and wait until the diesel indicator symbol in the combined instrument panel goes out, see page 43. – Following which, turn the ignition dial to position III.
06 Starting and driving Manual gearbox 06 Gear positions, five-speed Reverse gear inhibitor, five-speed Gear positions, six-speed (petrol) Depress the clutch pedal fully with each gear change. Remove your foot from the clutch pedal between gear changes! Follow the appropriate shifting pattern. Only engage reverse gear when the car is stationary. To engage reverse gear, the gear lever must first be put in position N.
06 Starting and driving Manual gearbox Reverse gear inhibitor, six-speed (petrol) Only engage reverse gear when the car is stationary. NOTE Reverse gear is electronically blocked if the car is travelling faster than approx. 20 km/h. Gear positions, six-speed (diesel)1 Depress the clutch pedal completely for each gear change. Remove your foot from the clutch pedal between gear changes. Follow the indicated gear pattern. For optimum fuel economy use the highest possible gear as often as possible.
06 Starting and driving Automatic gearbox Cold start When starting in low temperatures, the gear changes can sometimes feel hard. This is due to the gearbox oil’s viscosity at low temperatures. To minimise engine emissions, the gearbox shifts up later than normal when the engine is started at low temperatures. NOTE Depending on the engine temperature when the engine is started, the idle speed after a cold start may be higher than normal for certain engine types.
06 Starting and driving Automatic gearbox Disengaging shiftlock Mechanical gear selector inhibitor Automatic gear positions In certain cases, it may be necessary to move the car when it is not driveable, for example if the battery is flat. Proceed as follows to move the car: The gear selector can be moved freely between N and D. Other positions are locked with a latch that is released with the inhibitor button on the gear selector.
06 Starting and driving Automatic gearbox The gearbox is mechanically blocked when P position is engaged. Always apply the parking brake when parking the car. R – Reverse The car must be stationary when R is selected. N – Neutral N is the neutral position. No gear is engaged and the engine can be started. Apply the parking brake when the car is stationary with the gear selector in position N. 06 D – Drive D is the normal driving position.
06 Starting and driving All-wheel drive All-wheel drive – AWD All-wheel drive is always engaged. All-wheel drive means that all four road wheels are driven at the same time. Power is automatically distributed between front and rear wheels. An electronically controlled clutch system distributes the power to the pair of wheels that grips best. This provides the best traction and prevents wheel spin. Under normal driving conditions, the majority of power is transmitted to the front wheels.
06 Starting and driving Brake system Brake servo If the car is rolling or is being towed with the engine turned off, the brake pedal must be pressed about five times harder than when the engine is running. If the brake pedal is pressed when the engine is started, you will feel the pedal drop. This is normal and due to the brake servo becoming active. This may be more noticeable if the car has emergency brake assistance (EBA). WARNING The brake servo only works when the engine is running.
06 Starting and driving Brake system Emergency brake assistance – EBA (Emergency brake assistance) In case of sudden braking, full-strength braking is provided instantaneously. The EBA function senses when heavy braking is underway by registering how quickly the brake pedal is depressed. Continue braking without easing off on the brake pedal. The function is suspended when the pressure on the brake pedal eases. This function is always active and cannot be disengaged.
06 Starting and driving Stability and traction control system General The Dynamic Stability and Traction Control system (STC/DSTC) improves the car’s traction and helps the driver to avoid skidding. Traction control system The function is active at low speed and transfers power from the driving wheel that is spinning to the one that is not. Reduced operation A pulsing sound may be noticed during braking or acceleration when the system is in action. The car may accelerate more slowly than expected.
06 Starting and driving Stability and traction control system DSTC ON means that the system function is unchanged. ANTI-SKID SERVICE REQUIRED means that the system has been disabled due to a fault. DSTC SPIN CONTROL OFF means that system operation is reduced. – Stop the car in a safe place and turn off the engine. If the message remains when the engine is restarted, drive to an authorised Volvo workshop. – Press and hold RESET (B) until the STC/DSTC menu is changed.
06 Starting and driving Parking assistance (option) General 1 Function The system is activated automatically when the car is started and the text message Park Assist active, Exit to deactivate is shown on the audio system display. Parking assistance is active at speeds below 15 km/h. The system is deactivated at higher speeds. The system is reactivated when the speed falls below 10 km/h again. The frequency of the signal increases as you come closer to an object in front of or behind the car.
06 Starting and driving Parking assistance (option) Activating/deactivating Parking assistance can be deactivated by pressing EXIT on the control panel, see page 66. Park Assist deactivated Enter to activate will then appear on the audio system display. Parking assistance can be reactivated by pressing ENTER on the control panel. The display then shows Park Assist active Exit to deactivate.
06 Starting and driving Blind Spot Information System BLIS (option) General attention to vehicles moving in the same direction in the so-called "blind spot". Blind spots The system is designed to work most effectively when driving in dense traffic on multilane highways. BLIS is based on digital camera technology. The cameras (1) are located under the door mirrors. When a camera has detected a vehicle inside the blind spot zone the indicator lamp (2) comes on with a constant glow.
06 Starting and driving Blind Spot Information System BLIS (option) When BLIS operates The system operates when the car is driven at a speed above 10 km/h. Overtaking The system is designed to react if you overtake another vehicle at a speed of up to 10 km/h faster than the other vehicle. The system is designed to react if you are overtaken by a vehicle travelling up to 70 km/h faster than your vehicle. WARNING BLIS does not work in sharp bends. BLIS does not work when the car is reversing.
06 Starting and driving Blind Spot Information System BLIS (option) READ button to clear the text message. For more information on messages, see page 46. BLIS system message Text on the display 06 130 System status BLIND-SPOT SYST SERVICE REQUIRED Blind spot syst. disengaged. Contact an authorised Volvo workshop. BLIS FUNCTION REDUCED Reduced function. BLIND-SPOT SYST CAMERA BLOCKED One or both cameras blocked. Clean the lenses. BLIND-SPOT INFO SYSTEM OFF BLIS system off.
06 Starting and driving Towing and recovery Never tow the car to bump start it Jump start the car with a donor battery if the battery is flat and the engine does not start. Do not bump start the car. IMPORTANT Bump starting the car can damage the catalytic converter. Towing Find out the highest legal speed for towing before towing the car. – Turn the ignition switch to position II and unlock the steering lock so that the car can be steered, see page 114.
06 Starting and driving Towing and recovery 2. Release the cover (1) on the bumper with a screwdriver or coin in the bottom edge. 3. Screw in the towing eye (3) firmly, right up to the flange. Use the wheel wrench to tighten the towing eye. 4. After use, unscrew the towing eye and return it in the cargo area. Refit the cover on the bumper. IMPORTANT The towing eye is only designed for towing on roads, not for pulling the car unstuck or out of a ditch. Call a recovery service for assistance.
06 Starting and driving Start assistance Starting with a donor battery – – – – – If the battery in the car has become flat, you can "borrow" electric current from either a separate battery or the battery in another car. Always make sure the crocodile clips on the jump leads are attached securely to eliminate sparks during the start attempt. When jump starting the car, the following steps are recommended to avoid risk of explosion: – ensure that the cars do not touch one another.
06 Starting and driving Driving with a trailer General The load capacity is affected by extra accessories mounted on the car, such as a towbar, load carriers, space box, the passengers’ combined weight etc. as well as the load on the towball. The load capacity of the car is reduced by the number of passengers and their weight. If the towing bracket is fitted by an authorised Volvo workshop, then the car is delivered with the necessary equipment for driving with a trailer.
06 Starting and driving Driving with a trailer Automatic gearbox, driving with a trailer Diesel 1.6D engine with manual gearbox, driving with a trailer Parking on a hill 1. Apply the parking brake (handbrake). 2. Move the gear selector to parking position P. If the car is driven with a major load in a hot climate, the engine cooling fan can be replaced with one of a greater capacity than the standard model. Check with your nearest Volvo dealer regarding the options for your car. Starting on a hill 1.
06 Starting and driving Towing equipment Towbars Trailer cable The towball must be cleaned and greased regularly. If a towball hitch with vibration damper is used, it is not necessary to grease the towball. If the car is equipped with a detachable towbar, the towball mounting instructions must be followed carefully, see page 138. WARNING Be sure to attach the trailer’s safety cable to the correct place.
06 Starting and driving Towing equipment Specifications Dimensions for mounting points (mm) Fixed or detachable towbar A B C D E F G H I J K 1060 90 964 482 40 141 497 150 113 100 140 1 Side member 2 Ball centre 06 137
06 Starting and driving Detachable towbar Fitting the towball – Remove the guard plug. 06 138 – Ensure that the mechanism is in the unlocked position by turning the key clockwise. – Check that the indicator window (3) shows red. If the window does not show red, press in (1) and turn the locking wheel anticlockwise (2) until you hear a click.
06 Starting and driving Detachable towbar – Insert the towball section until your hear a click. – Check that the indicator window shows green. – Turn the key anticlockwise to the locked position. Remove the key from the lock.
06 Starting and driving Detachable towbar NOTE 06 140 Check that the towball section is secure by pulling it up, down and back. If the towball section is not fitted correctly then it must be removed and refitted in accordance with the previous steps NOTE The trailer’s safety cable must be attached to the attachment on the towbar.
06 Starting and driving Detachable towbar Removing the towball – Insert the key and turn it clockwise to the unlocked position. – Push in the locking wheel (1) and turn it anticlockwise (2) until you hear a click. – Turn the locking wheel down fully, until it comes to a stop. Hold it in this position while pulling the towball rearward and upward.
06 Starting and driving Detachable towbar – Insert the guard plug.
06 Starting and driving Loading General The load capacity is affected by extra accessories mounted on the car, such as a towbar, load carriers, space box, the passengers’ combined weight etc. as well as the load on the towball. The load capacity of the car is reduced by the number of passengers and their weight. For information on permitted weights, see page 229. WARNING The car’s driving characteristics change depending on how heavily it is loaded and how the load is distributed.
06 Starting and driving Adjusting headlamp pattern Correct light pattern for left or righthand traffic A. Headlamp pattern for left-hand traffic. B. Right-hand traffic. 06 144 The headlamps’ projection can be adjusted to avoid dazzling other motorists. The correct pattern will also better illuminate the verge. Halogen headlamps Bi-Xenon headlamps The headlamp control should be in position (A) for left-hand traffic and position (B) for right-hand traffic.
06 Starting and driving 06 145
General................................................................................................... 148 Tyre pressure .......................................................................................... 152 Warning triangle and spare wheel.......................................................... 154 Changing wheels.................................................................................... 156 Emergency puncture repair ...................................................................
WHEELS AND TYRES 07
07 Wheels and tyres General Driving characteristics and tyres Speed ratings New tyres The tyres greatly affect the car’s driving characteristics. The type of tyre, dimensions, tyre pressure and speed rating are important for how the car performs. The car has "Whole Vehicle Type Approval", which means that dimensions and speed ratings must not differ from those specified on the vehicle’s registration document.
07 Wheels and tyres General More even wear and maintenance Wheels should be stored lying down or hanging up, and not standing up. Tyres with tread wear indicators Tread wear indicators are narrow treadless bands across the width of the tread. On the side of the tyre are the letters TWI (Tread Wear Indicator). When the tyre’s tread depth is down to 1.6 mm, the tread depth will be level in height with the tread wear indicators. Change to new tyres as soon as possible.
07 Wheels and tyres General Rims and wheel nuts Steel rims – standard wheel nuts (1) Steel rims are normally mounted with the standard wheel nuts, but the bulge acorn variety may also be used. WARNING Never use standard nuts for aluminium rims. The wheels can come loose. Standard (1) and bulge acorn (2) wheel nuts 07 Only use rims that are tested and approved by Volvo and which are Volvo genuine accessories. There are two types of wheel nut, depending on whether the rims are made of steel or aluminium.
07 Wheels and tyres General Summer and winter wheels and capacity to force rain, snow and slush out of the way are adversely affected. Tyres with the greatest tread depth should always be fitted to the rear of the car (to decrease the risk of skidding). Wheels should be stored lying down or hanging up, and not standing up. Contact an authorised Volvo workshop if you are uncertain about tread depth.
07 Wheels and tyres Tyre pressure Recommended tyre pressure Checking the tyre pressure Check the tyre pressure regularly. NOTE Tyre pressure decreases over time, this is a natural phenomenon. Tyre pressure also varies depending on ambient temperature. The tyre pressure label on the driver’s side door pillar shows which pressures the tyres should have at different load and speed conditions.
07 Wheels and tyres Tyre pressure Tyre pressure table Speed (km/h) Load,1-3 persons Front (kPa) Rear (kPa) Max. load Front (kPa) Rear (kPa) Variant Tyre size 1.6 1.8 2.0 1.
07 Wheels and tyres Warning triangle and spare wheel Warning triangle Follow the regulations for the use of a warning triangle1. Position the warning triangle in a suitable place with regard to traffic. 07 – Undo the case containing the warning triangle, it is attached with Velcro. Take the warning triangle out of the case. – Lower the warning triangle’s support legs. Ensure the warning triangle and its case are properly secured in the cargo area after use. 1 154 Certain markets.
07 Wheels and tyres Warning triangle and spare wheel Spare wheel and jack The car’s original jack The original jack1 should only be used for changing wheels. The jack’s thread should always be well greased. The spare wheel, jack and wheel spanner are found under the floor in the cargo area. Taking out the spare wheel – Fold the rear edge of the floor mat forward. – Release the spare wheel and lift it out. – Take out the jack and the wheel spanner.
07 Wheels and tyres Changing wheels Removing wheels Set up the warning triangle if a wheel must be replaced at a busy location. Make sure that the car and jack are on a firm horizontal surface. 07 156 – Take out the spare wheel, jack and wheel spanner, which are found under the carpet in the cargo area. – Apply the parking brake and engage first gear, or position P if the car has an automatic gearbox. – Place chocks in front of and behind the wheels which will remain on the ground.
07 Wheels and tyres Changing wheels Fitting the wheel – Clean the contract surfaces on the wheel and hub. – Put on the wheel. Tighten the wheel nuts. – Lower the car so that the wheel cannot rotate. – Tighten the wheel nuts crosswise. It is important that the wheel nuts are tightened properly. Tighten to 90 Nm. Check the torque with a torque spanner. – Put on the wheel cover (steel rim). WARNING Never crawl under the car when it is raised on the jack.
07 Wheels and tyres Emergency puncture repair General 07 Cars which do not have a spare wheel are instead equipped with an emergency puncture repair kit. This kit can be used to both seal the puncture and to check and adjust the tyre pressure. The kit consists of an electric air compressor and an integrated canister with sealing liquid. NOTE The jack is an option on cars equipped with emergency puncture repair kit.
07 Wheels and tyres Emergency puncture repair The emergency puncture repair kit has limited abilities to seal tyres which have punctures in the wall of the tyre. Do not seal tyres with the emergency puncture repair kit if they have larger slits, cracks, irregularities or similar damage. The emergency puncture repair kit with compressor and tools are found under the floor in the cargo area. 12 V sockets for the compressor are located by the centre console in the front, by the rear seat and in the cargo area.
07 Wheels and tyres Emergency puncture repair Inflating tyres Set up the warning triangle if a tyre must be inflated in an area close to traffic. 07 160 – Ensure that the orange switch (2) is in position 0 and take out the lead (5) and air hose (4) from the side compartment (3). – Screw the air hose’s valve connection to the bottom of the thread on the tyre’s air valve. – Connect the lead (5) to one of the car’s 12 V sockets. – Start the engine. The car must be in a wellventilated place.
07 Wheels and tyres Emergency puncture repair Sealing punctured tyres Set up the warning triangle if emergency tyre repairs must be carried out in an area where there is other traffic. – Remove the decal (1) regarding the highest permitted speed from the emergency puncture repair kit and stick it on the steering wheel where it can be clearly seen by the driver. – Ensure that the orange switch (2) is in position 0 and take out the lead (5) and air hose (4) from the side compartment (3).
07 Wheels and tyres Emergency puncture repair Check the tyre pressure again: WARNING Never stand next to the tyre when the compressor is running. Be particularly observant of the tyre walls. If cracks, irregularities or other damage appears, turn off the compressor immediately. Under these circumstances your journey should not continue. Contact an authorised tyre centre. – Undo the air hose (4) from the air valve and put the dust cap back on. Unplug the lead (5) from the electrical socket.
07 Wheels and tyres Emergency puncture repair Changing the sealing fluid canister The canister of sealing fluid should be changed before the best-before date has expired, see date label (1), or after the tyre has been sealed. After use, the canister (6) with holder (8) and air hose (10) should be changed. This replacement can be carried out by an authorised Volvo workshop or by following the instructions. IMPORTANT Read the safety instructions on the bottom of the canister.
07 Wheels and tyres Emergency puncture repair 07 164 Changing the canister and hose after use – Undo the two screws (2) on the orangecoloured case (3). – Remove the speed label (4) and date label (1), and open the safety catch (5). Loosen the case (3) and take it off. – Push down the button (8) while turning the canister (6) and the holder (9) clockwise. Remove them. – Pull out the air hose (10). – Wipe off remaining sealing fluid with a rag or scrape it away if it is has already dried.
07 Wheels and tyres 07 165
Cleaning ................................................................................................. 168 Touching up paintwork ........................................................................... 171 Rustproofing ..........................................................................................
CAR CARE 08
08 Car care Cleaning Washing the car Wash the car as soon as it becomes dirty. Use car shampoo. Dirt and road salt can lead to corrosion. • Do not park the car in direct sunshine. Washing a car with hot paintwork can cause permanent paintwork damage. Wash the car in a car wash with waste water separator. • Thoroughly rinse dirt off the underbody of the car. • Rinse the entire car to remove loose dirt.
08 Car care Cleaning Polishing and waxing Polish and wax the car if the paintwork is dull or to give the paintwork extra protection. The car does not need to be polished until it is at least one year old. However, the car can be waxed during this time. Do not polish or wax the car in direct sunlight. Wash and dry the car thoroughly before you begin polishing or waxing. Clean off asphalt and tar stains using Volvo tar remover or white spirit.
08 Car care Cleaning IMPORTANT Note that materials with colour that runs when dry (new jeans, suede garments etc.) may discolour the upholstery material. To achieve best results Volvo recommends cleaning and application of the protective cream two to four times per year. Ask your Volvo dealer about Volvo’s Leather Care product 08 170 Washing instructions for leather upholstery – Pour the leather cleaner on the dampened sponge and squeeze out a strong foam.
08 Car care Touching up paintwork Paintwork Stone chips and scratches Paint is an important part of the car’s rustproofing and should therefore be checked regularly. To avoid the onset of rust, damaged paintwork must be rectified immediately. The most common types of paintwork damage are stone chips, scratches, and marks on the edges of wings and doors. Colour code If the stone chip has penetrated to the bare metal – Stick a piece of masking tape over the damaged surface.
08 Car care Rustproofing Inspection and maintenance Your car received a thorough and complete rustproofing at the factory. Parts of the body are made of galvanised sheet metal. The underbody is protected by a wear-resistant anti-corrosion compound. And, a thin, penetrating rustproofing fluid was sprayed into the members, cavities and closed sections. Maintain the car’s rustproofing. • Keep the car clean. Hose down the underbody.
08 Car care 08 173
Volvo service .......................................................................................... 176 Self-maintenance ................................................................................... 177 Bonnet and engine compartment .......................................................... 178 Diesel ..................................................................................................... 179 Oils and fluids ............................................................................
MAINTENANCE AND SERVICE 09
09 Maintenance and service 09 Volvo service Volvo service programme Installing accessories Before the car left the factory, it was thoroughly test driven. It was checked again in accordance with Volvo Car Corporation regulations before it was handed over to you. The incorrect connection and installation of accessories can negatively affect the car’s electrical system. Certain accessories only function when the appropriate software has been programmed into the car’s electrical system.
09 Maintenance and service Self-maintenance Before starting work on the car Battery • Check that the battery cables are correctly connected and tightened. • Never disconnect the battery when the engine is running (e.g. if replacing the battery). • Never use a quick charger to charge the battery. The battery cables must be disconnected when charging the battery. The battery contains acid that is both corrosive and toxic. Handle the battery in an environmentally-suitable way. Let your Volvo dealer assist you.
09 Maintenance and service 09 Bonnet and engine compartment Opening the bonnet – Pull the handle on the far left under the dashboard. You will hear when the catch releases. – Insert your hand under the centre of the front edge of the bonnet and press the safety catch to the right. – Open the bonnet. WARNING Check that the bonnet locks properly when closed. Engine compartment 1. Washer fluid reservoir (4-cyl.) 2. Coolant expansion tank 3.
09 Maintenance and service Diesel Fuel system Diesel must fulfil the EN 590 or JIS K2204 standards. Diesel engines are sensitive to contaminants, such as high volumes of sulphur particles for example. Only use diesel fuel from a well-known producers. Never use diesel of dubious quality. At low temperatures (–40 °C to –6 °C), a paraffin precipitate may form in the diesel fuel, which can lead to ignition problems.
09 Maintenance and service 09 Oils and fluids Engine compartment decal for oil grade Checking the engine oil and oil filter Volvo recommends oil products. Change the oil and oil filter in accordance with the intervals specified in the Service and Warranty Booklet. IMPORTANT Dipstick, petrol engines IMPORTANT Always use oil of the prescribed grade, see the engine compartment decal. Check the oil level frequently and change the oil regularly.
09 Maintenance and service Oils and fluids display texts. Certain models have both variants. Contact an authorised Volvo dealer for more information. Checking the oil Checking the oil level in a new car is especially important before the first scheduled oil change. The Service and Warranty Booklet specifies the odometer readings for oil changes. Volvo recommends checking the oil level every 2 500 km. The most accurate measurements are made on a cold engine before starting.
09 Maintenance and service Oils and fluids 09 Washer fluid, topping up NOTE Checking and topping up the coolant Mix the washer antifreeze and water before filling the reservoir. Location of washer fluid reservoir1. The windscreen and headlamp washers share a common reservoir. – Filler cap on 4-cylinder engines and diesel. – Filler cap on 5-cylinder engines. Add washer antifreeze during the winter so that the fluid does not freeze in the pump, reservoir and hoses. See the capacities on page 236.
09 Maintenance and service Oils and fluids Check the coolant regularly The level should lie between the MIN and MAX marks on the expansion tank. If the system is not filled sufficiently, high local temperatures could occur, causing a risk of damage (cracks) in the cylinder head. Top up the coolant when the level falls to the MIN mark. Checking and topping up the brake and clutch fluid 09 braking, such as driving in mountains or tropical climates with high humidity.
09 Maintenance and service 09 Oils and fluids Checking and topping up the power steering fluid NOTE Check the level frequently. The fluid does not require changing. For capacities and recommended fluid grade, see page 235. If a fault should arise in the power steering system or if the car is without power and must be towed, it can still be steered. However the steering will be much heavier than normal and it will require more effort to turn the wheel.
09 Maintenance and service Wiper blades 09 Changing the wiper blades NOTE The wiper blades are different lengths. The blade on the driver’s side is longer than the blade on the passenger side. – Turn up the wiper arm. – Press the button located on the wiper blade mounting and pull straight out (1), parallel with the wiper arm. – Slide in (2) the new wiper blade until a "click" is heard. – Check (3) that the blade is firmly installed. – Fold down the wiper arm.
09 Maintenance and service 09 Battery Battery care WARNING Batteries can generate oxyhydrogen gas, which is highly explosive. A spark, which can be generated if you connect the jump leads incorrectly, is sufficient to make the battery explode. The battery also contains sulphuric acid, which can cause serious burns. If the acid comes into contact with eyes, skin or clothing, flush with large quantities of water. If acid splashes into the eyes, seek medical advice immediately.
09 Maintenance and service Battery Symbols on the battery Risk of explosion. 09 Changing the battery Use protective goggles Further information in the owner’s manual. Store the battery out of the reach of children. The battery contains corrosive acid. Avoid sparks and naked flames. Removing the battery – Switch off the ignition and remove the key. – Wait at least 5 minutes before touching any electrical terminals.
09 Maintenance and service 09 Replacing bulbs General Changing front bulbs All bulb specifications are given on page 243.
09 Maintenance and service Replacing bulbs Dipped beam Removing the cover and bulb: – Remove the entire lamp housing. – Bend aside the catches and remove the cover. – Unplug the connector from the bulb. – Release the spring clip that secures the bulb. First, press it to the left to release it, then out and down. – Pull out the bulb. – Refit the lamp housing. 09 Main beam Fitting a new bulb – Fit the new bulb. It can only be fitted in one position.
09 Maintenance and service 09 190 Replacing bulbs Position/parking lamps Direction indicators Side marker lamps – Pull out the bulb holder with a pair of pliers. Do not pull out the bulb holder by pulling the electrical cable. – Replace the bulb. – Press the bulb holder back into place. It can only be fitted in one way. – Twist the bulb holder anticlockwise and remove it. – To remove the bulb from the bulb holder, press the bulb in and turn it anticlockwise.
09 Maintenance and service Replacing bulbs Fog lamps Removing the bulb holder 09 – Press the bulb holder into place and refit the cover. NOTE If the error message BULB FAILURE/ CHECK STOP LAMP remains after a faulty bulb has been replaced then consult an authorised Volvo workshop. – Switch off all lights and turn the ignition key to position 0. – Remove the panel from around the lamp housing. – Remove the two Torx screws securing the lamp housing and take out the lamp housing.
09 Maintenance and service 09 Replacing bulbs Location of the bulbs in the rear lamp cluster Bulb holder 1. 2. 3. 4. 5. 192 Brake light Position/parking lamps Direction indicators Rear fog lamp (one side) Reversing lamp Number plate lighting Courtesy lighting – Switch off all lights and turn the ignition key to position 0. – Remove the screw with a screwdriver. – Carefully detach the entire lamp housing and withdraw it. Turn the connector anticlockwise and pull out the bulb. – Replace the bulb.
09 Maintenance and service Replacing bulbs Cargo area Vanity mirror lighting – Insert a screwdriver and gently turn so that the lamp housing comes loose. – Remove the blown bulb. – Fit a new bulb. Removing the mirror glass: – Insert a screwdriver underneath the lower edge, in the centre. Carefully prise up the lug on the edge. – Insert the screwdriver under the edge on both the left and right side (at the black rubber points) and carefully prise so that the lens releases at the lower edge.
09 Maintenance and service 09 Fuses General All electrical functions and components are fused to protect the car’s electrical system from damage by short circuiting and overloading. The fuses are in two different locations in the car: • Relay/Fuse box in the engine compartment • Relay/fuse box in the passenger compartment. Changing If an electrical component or function does not work, it may be because the component’s fuse was temporarily overloaded and blew. – Look in the fuse diagram to locate the fuse.
09 Maintenance and service Fuses 09 Relay/fuse box in the engine compartment The fuse box has 36 fuse positions. Be sure to replace a blown fuse with a new fuse of the same colour and amperage. • 19–36 are of the "Mini Fuse" type. • Fuses 7–18 are of the "JCASE" type and should be replaced by an authorised Volvo workshop. • Fuses 1–6 are of the "Midi Fuse" type and may only be replaced by an authorised Volvo workshop. On the inside of the cover are tweezers to assist removing and fitting fuses.
09 Maintenance and service 09 Fuses 1. 2. 3. 4. 5. 6. Radiator fan .............................................................................. 50 A Power steering .................................................................. 80 A Supply to passenger compartment fuse box ...................... 60 A Supply to passenger compartment fuse box ...................... 60 A Climate control element, additional heater PTC (option) ..... 80 A Glow plugs (4-cyl. diesel) .......................................
09 Maintenance and service Fuses 09 25. Reserve ...................................................................................26. Ignition switch ................................................................... 15 A 27. A/C compressor ................................................................ 10 A 28. Reserve ...................................................................................29. Front fog lamp ................................................................... 15 A 30.
09 Maintenance and service 09 Fuses Relay/fuse box in the passenger compartment The fuse box has 50 fuse positions. The fuses are located under the glovebox. The box also provides space for several spare fuses. Tools for fuse replacement are located in the relay/fuse box in the engine compartment, see page 195. Changing fuses – Remove the trim concealing the fuse box by pressing in the pin in the centre of the clips (1) about one cm and then withdrawing the clips.
09 Maintenance and service Fuses 37. Reserve ...................................................................................38. Reserve ...................................................................................39. Reserve ...................................................................................40. Reserve ...................................................................................41. Reserve ...................................................................................42.
09 Maintenance and service 09 Fuses 60. Seat heating (driver’s side)................................................. 15 A 61. Seat heating (passenger side) ............................................ 15 A 62. Sunroof ............................................................................ 20 A 63. Supply to rear right door .................................................... 20 A 64. Audio system, RTI (option) ................................................... 5 A 65. Infotainment system ...........
09 Maintenance and service 09 201
General................................................................................................... 204 Audio functions ...................................................................................... 205 Radio functions ...................................................................................... 207 CD functions .......................................................................................... 211 Menu structure – audio system..................................................
INFOTAINMENT SYSTEM 10
10 Infotainment system General Infotainment system 10 to be active until the key is removed from the ignition switch. The audio system is then started automatically the next time the key is turned to position I. Menus Some infotainment system functions are controlled via a menu system. The current menu level is shown at the top right of the display. Menu options are shown in the middle of the display. Infotainment is a system that integrates the audio system and the phone1.
10 Infotainment system Audio functions Audio controls Audio source selection Repeatedly pressing AM/FM switches between FM1, FM2 and AM. Repeatedly pressing MODE switches between CD and AUX. AUX1 The AUX input can be used for connecting an MP3 player for example. Sometimes the AUX external audio source can be heard at a different volume to the internal audio sources, e.g. the CD player. If the audio volume of the external audio source is too high then the sound quality can be impaired.
10 Infotainment system Audio functions 10 • CENTRE 1 – Centre speaker level. Three channel stereo or Pro Logic II must be activated before adjustment is possible. See page 206. • SURROUND 1 – Surround sound level. Pro Logic II must be activated before adjustment is possible. See page 206. Activating/deactivating the subwoofer – Press MENU and then ENTER. – Scroll to Audio settings and press ENTER. – Scroll to Subwoofer and press ENTER.
10 Infotainment system Radio functions Radio controls Manual tuning – Select wavelength using AM/FM (1). – Adjust the frequency by turning TUNING (3). Tune into a station with a long press (left or right) on the navigation button or by using the steering wheel keypad: – Hold the right or left side of the navigation button depressed until the desired frequency appears in the display.
10 Infotainment system Radio functions 10 Storing autostored presets in another memory An autostored preset can be transferred to the FM or AM memory. – Briefly press AUTO (7). Auto appears in the display. – Press a preset button. – Press the button under which the station will be stored and hold it depressed until the message Station stored appears in the display. The radio exits Auto mode and the stored station can be selected as a preset.
10 Infotainment system Radio functions Activating/deactivating TP – Press MENU and then ENTER. – Scroll to TP and press ENTER. TP from current station/all stations The radio can interrupt with traffic information from only the set (current) station or from all stations. – Select an FM station. – Press MENU and then ENTER. – Scroll to Advanced radio settings and press ENTER. – Scroll to TP and press ENTER. – Scroll to TP Station and press ENTER.
10 Infotainment system Radio functions Display of programme type 10 The programme type of the current station can be shown on the display. NOTE Not all radio stations support this function. Activating/deactivating display – Press MENU and then ENTER. – Scroll to PTY and press ENTER. – Scroll to Show PTY and press ENTER. Activating/deactivating AF – Press MENU and then ENTER. – Scroll to Advanced radio settings and press ENTER. – Scroll to AF and press ENTER.
10 Infotainment system CD functions CD function controls Starting playback (CD changer) If a CD position with a music CD is already selected when the audio system is activated then playback starts automatically. Otherwise change to CD changer mode using MODE and select a disc with the number buttons 1 –6 or Up/Down on the navigation button. Inserting a CD (CD changer) – Select an empty position with buttons 1–6 or Up/Down on the navigation button. An empty position is marked on the display.
10 Infotainment system CD functions 10 automatically when all files in the current directory have been played back. Press left/right on the navigation button if the display is not wide enough to show the whole audio file name. Fast-wind/change CD tracks and audio files Short presses right/left on the navigation button are used to scroll between CD tracks/ audio files. Long presses are used to fastwind CD tracks/audio files. TUNING (or the steering wheel keypad) can also be used for this purpose.
10 Infotainment system Menu structure – audio system FM menu 1. News 2. TP 3. PTY 4. Radio text 5. Advanced radio settings 6. Audio settings1 AM menu 1. Audio settings1 CD menu 1. Random 2. News 3. TP 4. Disc text 5. Audio settings1 1 CD changer menu 1. Random 2. News 3. TP 4. Disc text 5. Audio settings1 10 AUX menu 1. AUX volume 2. News 3. TP 4. Audio settings1 Certain audio systems.
10 Infotainment system Phone functions (option) 10 Phone system components 214
10 Infotainment system Phone functions (option) Phone system components Emergency calls 1. Antenna Emergency calls to alarm centres can be made without a SIM card as long as there is coverage by a GSM operator. 2. Steering wheel keypad (option) Most phone system functions can be accessed via the keypad. See page 216. 3. Microphone The hands free microphone is integrated in the roof console beside the rearview mirror. 4.
10 Infotainment system Phone functions (option) 10 – Pull out the SIM card holder (1) in the SIM card reader. – Position the SIM card in the holder with the metal surface visible. The bevelled edge of the SIM card should align with the bevel of the SIM card holder. – Carefully press in the SIM card holder. Phone controls Steering wheel keypad Menus Page 204 describes how to control phone functions with the menu system.
10 Infotainment system Phone functions (option) On/Off A handset appears in the display when the phone system is active or in standby mode. If the ignition key is turned to position 0 when the phone is in one of these mode, the phone automatically resumes this mode the next time the key is turned to position I or II. Activating the phone system Phone system functions can only be used when the phone is in active mode. – Press PHONE. – Enter the PIN code (if necessary) and press ENTER.
10 Infotainment system Phone functions (option) Volume 10 The phone uses the driver’s door or centre speaker1. Call volume Call volume is regulated with the buttons of the steering wheel keypad. If the privacy handset is used, volume is regulated with a wheel on the side of the handset. Audio system volume Audio system volume is temporarily lowered during a phone call. Once the call is ended the previous volume is resumed.
10 Infotainment system Phone functions (option) – Scroll to Search and press ENTER. – Enter the first few letters of the item and press ENTER, or simply press ENTER. – Scroll to an item and press ENTER. Speed dial A keypad button (1- 9) can be used as a speed dial number for a contact in the phone book. Copying entries between the SIM card and Phone book – Press MENU. – Scroll to Phone book and press ENTER. – Scroll to Copy all and press ENTER. – Scroll to SIM to phone or Phone to SIM and press ENTER.
10 Infotainment system Phone functions (option) • Swap – Switch between two calls (available if up to three parties are connected). 10 SMS – Short Message Service Reading SMS – Press MENU. – Scroll to Messages and press ENTER. – Scroll to Read and press ENTER. – Scroll to a message and press ENTER. The message text appears in the display. Additional selections can be made by pressing ENTER. Hold EXIT depressed to leave the menu system. Writing and sending – Press MENU. – Scroll to Messages and press ENTER.
10 Infotainment system Menu structure – phone Overview 1. Call register 1.1. Missed calls 1.2. Received calls 1.3. Dialled no. 1.4. Erase list 1.4.1. All calls 1.4.2. Missed calls 1.4.3. Received calls 1.4.4. Dialled no. 1.5. Call duration 1.5.1. Last call 1.5.2. Number of calls 1.5.3. Total time 1.5.4. Reset time 2. Messages 2.1. Read 2.2. Write 2.3. Message sett 2.3.1. SMSC number 2.3.2. Validity time 2.3.3. Message type 3. Phone book 3.1. New number 3.2. Search 3.3. Copy all 3.3.1. SIM to phone 3.3.2.
10 Infotainment system Menu structure – phone 10 5.5.3. Mute radio 5.5.4. Msg. beep 5.6. Traff. safety 5.6.1. Menu lock 5.6.2. IDIS 5.7. Factory sett. Description of menu options 1. Call register 1.1. Missed calls List of missed calls. You can choose to call, erase or store the number in the phone book. 1.2. Received calls List of received calls. You can choose to call, erase or store the number in the phone book. 1.3. Dialled no. List of previously dialled numbers.
10 Infotainment system Menu structure – phone 3.3. Copy all 4.3. Auto answer Copy phone numbers and names from the SIM card to the phone memory. Automatically answers incoming calls. 3.3.1. 3.3.2. Calls a previously engaged number. From SIM to phone memory From phone to SIM memory 3.4. One-key dial A number stored in the phone book can be stored as a speed dial number. 3.5. Erase SIM Erase the entire SIM card memory. 3.6. Erase phone Erase the entire phone memory. 3.7.
10 Infotainment system Menu structure – phone 5.5.2. 10 5.5.3. 5.5.4. Ring signal. There are seven different ring tones. Mute radio: On/Off Msg. beep 5.6. Traffic safety 5.6.1. 5.6.2. Menu lock. Deactivating the menu lock allows access to the entire menu while driving. IDIS. If the IDIS function is deactivated, incoming calls are not delayed, regardless of the driving situation. 5.7. Factory sett. Reset the system’s factory settings.
10 Infotainment system 10 225
Type designation .................................................................................... 228 Dimensions and weights ........................................................................ 229 Engine specifications ............................................................................. 230 Engine oil................................................................................................ 232 Fluids and lubricants......................................................................
SPECIFICATIONS 11
11 Specifications Type designation 11 Knowing the car’s type designation, vehicle identification and engine numbers can facilitate all contact with a Volvo dealer regarding the car and when ordering spare parts and accessories. 1. Type designation, vehicle identification number, maximum permissible weights, codes for colour and upholstery and type approval number. 2. Decal for parking heater. 3. Engine type designation, component and serial number. 4. Decal for engine oil. 5.
11 Specifications Dimensions and weights Dimensions Maximum load: See registration document. Length: 447 cm Max. roof load: 75 kg Width: 177 cm Trailer with brakes: Wheelbase: 264 cm Maximum trailer weight kg Front track: 154 – 155 cm Rear track: 153 – 154 cm 1.6 1200 Weights Kerb weight includes the driver, the fuel tank 90 % full and all fluids. The weight of passengers and accessories, such as a towbar, load carriers, space box etc.
11 Specifications Engine specifications Engine designation Output (kW/rpm) 11 1.6 1.8 2.0 2.4 2.4i T5 B4164S3 B4184S11 B4204S3 B5244S5 B5244S4 B5254T3 74/6000 92/6000 107/6000 103/5000 125/6000 162/5000 (hp/rpm) 100/6000 125/6000 145/6000 140/5000 170/6000 220/5000 Torque (Nm/rpm) 150/4000 165/4000 185/5000 220/4000 230/4400 320/1500–4800 No. of cylinders 4 4 4 5 5 5 Bore (mm) 79 83 87 83 83 83 Stroke (mm) 81,4 83,1 83 90 90 93.
11 Specifications Engine specifications 1.6D 2.0D 2.4D D5 D4164T D4204T D5244T91 D5244T8 Output (kW/rpm) 80/4000 100/4000 120/5500 132/4000 (hp/rpm) 109/4000 136/4000 163/5500 180/4000 240/- 320/2000 340/1750-2750 350/1750 - 3250 Engine designation Torque (Nm/rpm) No. of cylinders 4 4 5 5 Bore (mm) 75 85 81 81 93.2 Stroke (mm) 88,3 88 93.2 Swept volume (litres) 1.56 2.00 2.40 2.40 18.3:1 18.5:1 17.0:1 17.
11 Specifications Engine oil Adverse driving conditions Viscosity chart Check the oil level more frequently for long journeys: 11 • • • • towing a caravan or trailer. in mountainous regions. at high speeds. in temperatures colder than –30 °C or hotter than +40 °C. This can produce abnormally high oil temperature or oil consumption. Also check the oil level more often if the car is often driven short distances (less than 10 km) when temperatures are low (below +5 °C).
11 Specifications Engine oil Oil decal When the oil decal shown alongside here is in the car’s engine compartment, the following applies. See location on page 228. Oil grade: ACEA A3/B3/B4 Viscosity: SAE 0W–30 When driving under adverse conditions, use ACEA A5/B5 SAE 0W-30. Engine variant 2.4 B5244S5 2.4i B5244S4 T5 B5254T3 1Including Volume between MIN – MAX (litres) Volume1 (litres) 1.3 5.8 11 filter change.
11 Specifications Engine oil Oil decal When the oil decal shown alongside here is in the car’s engine compartment, the following applies. See location on page 228. Oil grade: WSS-M2C913-B Viscosity: SAE 5W–30 11 When driving under adverse conditions, use ACEA A5/B5 SAE 0W-30. Engine variant Volume1 (litres) 0.75 4.0 1.6 B4164S3 1.8 B4184S11 2.0 B4204S3 1.6D D4164T 1.0 3.7 2.0D D4204T 2.0 5.5 1Including 234 Volume between MIN – MAX (litres) filter change. 4.
11 Specifications Engine oil Oil decal When the oil decal shown alongside here is in the car’s engine compartment, the following applies. See location on page 228. Oil grade: ACEA A5/B5 Viscosity: SAE 0W–30 11 Engine variant D5 D5244T8 2.4D D5244T92 1 Including filter change 2 Belgium Volume between MIN – MAX (litres) Volume1 (litres) 1.
11 Specifications Fluids and lubricants Fluid System Gearbox oil 1.6 Manual 5 speed 2.1 1.8 Manual 5 speed 1.9 1.6D Manual 5 speed 1.9 1.8F Manual 5-speed 1.9 2.0 Manual 5-speed 1.9 2.0D Manual 5 speed 2.2 Transmission fluid: WSS-M2C200-C3 2.0D Manual 6 speed 1.7 Transmission fluid: WSD-M2C200-C D5 Automatic gearbox 7.75 Transmission fluid: JWS 3309 2.4 Automatic gearbox 7.75 Transmission fluid: JWS 3309 2.4i Manual 5 speed 2.1 Transmission fluid: MTF 97309-10 2.
11 Specifications Fluids and lubricants Fluid System Coolant 5-cyl. Petrol, manual gearbox 9.5 5-cyl. Petrol, automatic gearbox 10.0 5-cyl. Diesel (D5) 11.0 4-cyl. Petrol (1.8, 1.8F and 2.0) 7.5 4-cyl. Diesel (2.0D) 9.5 4-cyl. Petrol (1.6) 6.2 4-cyl. Diesel (1.6D) Air conditioning1 Brake fluid Fuel tank 1Weights Recommended oil grade: Coolant with corrosion inhibitor mixed with water, see packaging. The thermostat starts opening at: 90 ºC in petrol engines and at 82 ºC in diesel engines.
11 Specifications Fuel Consumption, emissions and volume Engine 11 Consumption1 litre/100 km Emissions of CO2 (g/km) Tank volume (litres) 55 1.6 B4164S3 Manual 5 speed (IB5) 7.2 171 1.8 B4184S11 Manual 5 speed (MTX75) 7.3 174 1.8F B4184S8 Manual 5 speed (MTX75) 7.4 177 2.0 B4204S3 Manual 5 speed (MTX75) 7.4 177 2.4 B5244S5 Automatic gearbox (AW55-50/51) 9.1 217 2.4i B5244S4 Manual 5 speed (M56H) 8.5 203 Automatic gearbox (AW55-50/51) 9.
11 Specifications Fuel Engine Gearbox Consumption litre/100 km Emissions of CO2 (g/km) Tank volume (litres) 52 1.6D D4164T (EURO3) (EURO4) Manual 5 speed (MTX75) 4.9 129 2.0D D4204T (EURO3) Manual 6 speed (MMT6) 5.6 148 5.8 154 5.6 148 5.6 148 (EURO4) (EURO3) Manual 5 speed (M56L2) (EURO4) D5 D5244T8 Automatic gearbox (AW55-51) 7.0 184 2.4D D5244T91 Automatic gearbox (AW55-51) 7.
11 Specifications Fuel Fuel consumption and emissions of carbon dioxide 11 Official fuel consumption figures are based on a standard driving cycle in accordance with EU Directive 80/1268 comb. Fuel consumption figures may change if the car is equipped with extra equipment that affects the car’s weight. The manner in which the car is driven and other non-technical factors can affect fuel consumption. Consumption is higher and power output lower for fuel with an octane rating of 91 RON.
11 Specifications Catalytic converter General Lambda-sondTM oxygen sensor The purpose of the catalytic converter is to purify exhaust gases. It is located in the flow of exhaust gasses close to the engine so that it quickly reaches operating temperature. The catalytic converter consists of a monolith (ceramic or metal) with channels. The channel walls are lined with a thin layer of platinum, rhodium and palladium. These metals act as catalysts, i.e.
11 Specifications Electrical system General 12 volt system with a voltage-regulated alternator. Single pole system in which the chassis and engine block are used as conductors. 11 Battery Voltage 12 V Cold start capacity (CCA) Reserve capacity (RC) 12 V 590 A 600 A 1 700 A2 100 min 120 min 135 min 60 70 80 Capacity (Ah) 1 12 V Cars equipped with High Performance audio system. 2 Cars equipped with diesel, keyless drive, audio system Premium Sound, fuel-driven heater or RTI.
11 Specifications Electrical system Bulbs Lighting Output W Socket Dipped beam 55 H7 Bi-Xenon 35 D2S Main beam 55 HB3 Brake lights, reversing lamps, rear fog lamp 21 BA15s Direction indicators, rear/front (yellow) 21 BAU 15s Rear position/parking lamps, rear side marker lamps 5 BAY15d Courtesy lighting, cargo area lighting, number plate lighting 5 SV8.5 Vanity mirror 1.2 SV5.5 5 W 2.1 x 9.5d Direction indicators in door mirrors (yellow) 5 W 2.1 x 9.
11 Specifications Electrical system Type approval, remote control system Country 11 A, B, CY, CZ, D, DK, E, EST, F, FIN, GB, GR, H, I, IRL, L, LT, LV, M, NL, P, PL, S, SK, SLO 1 IS, LI, N, CH HR ROK Delphi 2003-07-15, Germany R-LPD1-03-0151 BR RC ETC093LPD0155 1 Delphi hereby certifies that this remote control system conforms to the essential characteristic requirements and other relevant regulations of directive 1999/5/EC.
11 Specifications 11 245
Alphabetical index A Alarm, radio functions .............................. 208 A/C ..............................................................72 electronic climate control .......................76 manual climate control ...........................73 ABS ...........................................................122 ABS fault ................................................43 Active Yaw Control ...................................124 Additional heater .........................................
Alphabetical index Bulbs replacement .........................................188 specifications .......................................243 C Call functions during an ongoing call ..........219 phone volume ......................................218 Call waiting ................................................217 Calls making and receiving ...........................217 Car care leather upholstery ................................170 Car settings .................................................
Alphabetical index D Deadlocks .................................................103 temporary deactivation ........................103 temporary disconnection of alarm detectors ................................106 Defroster .....................................................73 Emissions system DSTC, see also Stability control system .. 124 capacities ............................. 233, 234, 235 changing .............................................. 180 driving under adverse driving conditions ........
Alphabetical index Fluids, capacities ..............................236, 237 Glovebox .................................................... 87 Instrument overview Fog lamps locking ................................................. 102 Gross vehicle weight ................................ 229 left-hand drive ................................ 36, 214 right-hand drive ..................................... 38 Integrated booster cushion ......................... 31 On/Off ...................................
Alphabetical index L Lambda-sond ............................................241 Leather upholstery, washing instructions .170 Lighting automatic lighting, dipped beam ...........48 automatic lighting, passenger compartment ..........................................84 bulb replacement, general ...................188 bulbs, specifications ............................243 dipped beam ..........................................48 display lighting .......................................49 exterior ..............
Alphabetical index Paintwork colour code ..........................................171 Parking assistance ....................................126 sensors for parking assistance ............127 Parking brake ........................................44, 57 Parking heater battery and fuel ......................................79 general ...................................................78 parking on a hill ......................................78 time setting ............................................
Alphabetical index Remote control system, type approval .....244 SIM card ................................................... 215 Starting from cold Reverse gear inhibitor SIPS bags ................................................... 21 five-speed ............................................116 six-speed, petrol ..................................117 Rustproofing .............................................172 SMS automatic gearbox ............................... 118 Starting the engine ............
Alphabetical index Surround ...........................................204, 206 Symbols ....................................................125 indicator symbols ...................................43 warning symbols ....................................42 T removing .............................................. 141 specifications ...................................... 137 Towing eye ............................................... 131 TP –traffic information ..............................
Alphabetical index Washing the car ........................................168 Water-repellent surface cleaning ................................................169 Waxing ......................................................169 Wheels fitting ....................................................157 removal ................................................156 rims ......................................................150 Whiplash injury WHIPS ...............................24 WHIPS ..........................
Volvo.
