DEAR VOLVO OWNER THANK YOU FOR CHOOSING VOLVO We hope that you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your passengers. Volvo is one of the safest cars in the world. Your Volvo has also been designed to satisfy all current safety and environmental requirements.
Contents 2 00 Introduction 01 Safety 02 Instruments and controls Introduction ........................................ 6 Seatbelts .......................................... 12 Overview, left-hand drive car ............ 36 Volvo Car Corporation and the environment........................................ 7 Airbag system .................................. Airbags (SRS) ................................... Activating/deactivating the airbag (SRS) ...............................
Contents 03 Climate control 04 Interior 05 Locks and alarm General information on climate control .............................................. Electronic climate control, ECC ....... Air distribution .................................. Fuel-driven heater (option) ............... Front seats ........................................ 76 Remote control with key blade......... 96 Electrically operated roof .................. 79 Wind deflector (option) ..................... 83 Wind deflector (option) ....
Contents 4 06 Starting and driving 07 Wheels and tyres 08 Car care General ........................................... 112 General........................................... 146 Cleaning.......................................... 168 Refuelling........................................ 114 Starting the engine ......................... 115 Diesel particle filter (DPF) ............... 116 Ignition switch and steering lock..... 117 Manual gearbox.............................. 118 Automatic gearbox .......
Contents 09 Maintenance and service 10 Infotainment system 11 Specifications Volvo service ................................... 176 General ........................................... 204 Self-maintenance ........................... Bonnet and engine compartment .. Diesel.............................................. Oils and fluids ................................ Wiper blades .................................. Battery........................................... Replacing bulbs ........................
Introduction Introduction Owner’s Manual A good way of getting to know your new car is to read the owner’s manual, ideally before your first journey. This will give you the opportunity to familiarise yourself with new functions, to see how best to handle the car in different situations, and to make the best use of all the car’s features.
Introduction Volvo Car Corporation and the environment Volvo Cars’ environmental philosophy Environmental care, safety and quality are the three core values which influence all operations of the Volvo Car Corporation. We also believe that our customers share our consideration for the environment. EPI (Environmental Product Information) is supplied for all Volvo models. You can now compare the environmental impact of different models and engines during the entire lifecycle.
Introduction Volvo Car Corporation and the environment Efficient emission control Your Volvo is manufactured following the concept Clean inside and out – a concept that encompasses a clean interior environment as well as highly efficient emission control. In many cases the exhaust emissions are well below the applicable standards. In addition there is a special radiator coating, PremAir®1, which can convert hazardous ground-level ozone into pure oxygen when the ozone passes the radiator.
Introduction Volvo Car Corporation and the environment Reducing environmental impact You can easily help to reduce environmental impact, for example, by driving economically, by purchasing eco-labelled car care products and by servicing and maintaining the car according to the instructions in the owner’s manual. The following hints will help you to do your bit for the environment: • Decrease fuel consumption by choosing ECO tyre pressure, see page 150.
Seatbelts .................................................................................................. Airbag system .......................................................................................... Airbags (SRS) ........................................................................................... Activating/deactivating the airbag (SRS) ....................................................................................... Side airbags (SIPS bags) ......................................
SAFETY 01
01 Safety 01 Seatbelts Always use a seatbelt feed the belt in by hand so that it does not hang lose. WARNING Each belt is intended for one person only. The belt locks and cannot be withdrawn • if it is pulled out too quickly. • during braking and acceleration. • if the car leans heavily. It is important that the belt lies against the body so it can provide maximum protection. Do not lean the backrest too far back. The seatbelt is designed to protect in a normal seating position.
01 Safety Seatbelts Seatbelt reminder Unbelted occupants will be reminded to fasten their seatbelts through an audio and visual reminder. The audio reminder is speed-dependent. The visual reminder is located in the roof console and the combined instrument panel. At low speed, the audio reminder will sound for the first six seconds. Child seats are not covered by the seatbelt reminder system.
01 Safety 01 Seatbelts the vehicle as they drive (which means they must be able to easily operate the foot pedals and steering wheel). Within this context, they should strive to position the seat with as large a distance as possible between their abdomen and the steering wheel. Seatbelt guide Seatbelt tensioner All the seatbelts are equipped with belt tensioners. A mechanism in the belt tensioner tightens the seatbelt around the body in the event of a sufficiently forceful collision.
01 Safety Airbag system Warning symbol on the combined instrument panel 01 As well as the warning symbol, a message may appear on the information display in appropriate cases. If the warning symbol malfunctions, the warning triangle illuminates and the message SRS AIRBAG SERVICE REQUIRED or SRS AIRBAG SERVICE URGENT appears in the information display. Contact an authorised Volvo workshop urgently. WARNING The airbag system1 is continually monitored by the system control module.
01 Safety 01 Airbags (SRS) Airbag (SRS) on the driver’s side Passenger airbag (SRS) WARNING Never place a child in a child seat or on a booster cushion in the front seat if the airbag (SRS) is activated.1 Never allow a child to stand or sit in front of the front passenger seat. No one shorter than 140 cm should sit in the front passenger seat if the airbag (SRS) is activated. Failure to follow the advice given above can endanger the life of the child.
01 Safety Airbags (SRS) SRS system 01 WARNING Repairs must only be performed by an authorised Volvo workshop. Unauthorised work on the SRS system could cause malfunction and result in serious injury. SRS system, left-hand drive. The system consists of airbags and sensors. A sufficiently violent collision trips the sensors and the airbag(s) are inflated with hot gas. To cushion the impact, the airbag deflates when compressed. When this occurs, smoke escapes into the car. This is completely normal.
01 Safety 01 Airbags (SRS) Location of the passenger airbag in left-hand drive and right-hand drive cars WARNING Never interfere with SRS components in the steering wheel or the panel above the glovebox. Objects and accessories must not be positioned or glued on or near the SRS AIRBAG panel (above the glovebox) or in the area affected by a deployed airbag.
01 Safety Activating/deactivating the airbag (SRS) PACOS (option) Activating/deactivating 01 WARNING Activated airbag (passenger seat): Never place a child in a child seat or on a booster cushion on the front passenger seat when the airbag is activated. This applies to everyone shorter than 140 cm. Deactivated airbag (passenger seat): No one taller than 140 cm should ever sit in the front passenger seat when the airbag is deactivated. Failure to follow the advice given above can endanger life.
01 Safety 01 Activating/deactivating the airbag (SRS) Switch position WARNING Do not allow anyone to sit in the front passenger seat if the text message in the roof panel indicates that the airbag (SRS) is deactivated and if the warning symbol for the AIRBAG system is also displayed on the combined instrument panel. This indicates that there has been a severe malfunction. Visit an authorised Volvo workshop urgently. 20 Switch for SRS in ON position. Switch for SRS in OFF position.
01 Safety Side airbags (SIPS bags) Side airbags – SIPS bags 01 WARNING Do not put objects in the area between the outside of the seat and the door panel, since this area is required by the side airbag. WARNING Use only Volvo genuine car seat covers, or seat covers approved by Volvo. Other seat covers may impede the operation of the side air bags. Child seats and side airbags Side airbag locations.
01 Safety 01 Side airbags (SIPS bags) SIPS bags Driver’s side The SIPS bag system consists of side airbags and sensors. A sufficiently violent collision trips the sensors and the side airbags are inflated. The airbag inflates between the occupant and the door panel and thereby cushions the initial impact while deflating. The side airbag is normally only deployed on the side of the collision.
01 Safety Inflatable Curtain (IC) 01 Properties The inflatable curtain, DMIC (Door Mounted Inflatable Curtain), is a supplement to the SIPS system. It is fitted inside along the driver’s and passenger side and protects both front seat passengers. The inflatable curtain is activated by sensors in the event of a sufficiently violent collision or if the car is at risk of overturning. When deployed, the inflatable curtain inflates.
01 Safety 01 WHIPS Protection against whiplash injury – WHIPS The whiplash protection system (WHIPS) consists of energy absorbing backrests and specially designed head restraints for the front seats. The system is actuated by a rearend collision, where the angle and speed of the collision, and the nature of the colliding vehicle all have an influence.
01 Safety WHIPS 01 Do not obstruct the WHIPS system WARNING If a seat has been subjected to extreme forces, such as due to a rear-end collision, the WHIPS system must be checked by an authorised Volvo workshop. Part of the WHIPS system’s protective capacity may have been lost even if the seat appears to be undamaged. Contact an authorised Volvo workshop to have the system checked after even a minor rear-end collision.
01 Safety 01 Roll-Over Protection System (ROPS) Function Always contact an authorised Volvo workshop if the ROPS system has deployed. WARNING Do not carry out any work on the ROPS system. Do not place any objects on the ROPS system or behind the passengers’ head restraints. Roll bars in raised position. The ROPS system consists of strong roll bars which are located behind the passengers’ head restraints, as well as sensors.
01 Safety When the systems deploy System Triggered Seatbelt tensioner In a frontal collision and/or side-impact accident and/or overturning. Airbags (SRS) In a frontal collision1. Side airbags (SIPS) In a side-impact accident1. Inflatable Curtain DMIC In a side-impact accident1. Whiplash protection WHIPS In a rear-end collision. Roll-Over Protection System (ROPS) In the event of overturning and/or collision from behind.
01 Safety 01 Crash mode Driving after a collision If everything seems normal and you have checked for indications of fuel leakage, you may attempt to start the car. Firstly, remove the ignition key and then reinsert it. The car’s electronics will then try to reset themselves to normal mode. Then try to start the car. If CRASH MODE is still shown on the display then the car must not be driven or towed.
01 Safety Child safety Children should sit comfortably and safely 01 Child seats and airbags The position of a child in the car and the choice of equipment is dictated by the child’s weight and size. For more information see page 31. NOTE Regulations regarding the placement of children in cars vary from country to country. Check what laws apply. Children of all ages and sizes must always sit correctly secured in the car. Never allow a child to sit on the knee of a passenger.
01 Safety 01 Child safety Decal located on instrument panel end face. 30 Decal located on instrument panel end face (Australia only).
01 Safety Child safety 01 Placement of children in the car Weight/age Front seat1 Outer rear seat <10 kg (0–9 months) Rear-facing child seat, secured with seatbelt and straps. Use a protective cushion between the child seat and the dashboard. L2: Type approval no. E5 03135 Rear-facing child seat, secured with seatbelt, support legs, straps and attachment eyes3. L2: Type approval no. E5 03135 9–18 kg (9–36 months) Rear-facing child seat, secured with seatbelt and straps.
01 Safety 01 Child safety Fitting a child seat WARNING Never place a child in a child seat or on a booster cushion in the front seat if the airbag (SRS) is activated 1. No one shorter than 140 cm should sit in the front passenger seat if the airbag (SRS) is activated.1 Failure to follow the advice given above can endanger the life of the child. 1For information on activated/deactivated airbag (SRS) see page 19. Volvo has child safety products that are designed for and tested by Volvo.
01 Safety Child safety 01 ISOFIX fixture system for child seats (option) The outer rear seats have ISOFIX attachment points. Contact a Volvo dealer for further information on child safety equipment.
Overview, left-hand drive car ................................................................... Overview, right-hand drive car ................................................................. Driver’s door control panel....................................................................... Combined instrument panel..................................................................... Indicator and warning symbols ................................................................ Information display.........
INSTRUMENTS AND CONTROLS 02
02 Instruments and controls Overview, left-hand drive car 02 36
02 Instruments and controls Overview, left-hand drive car 1. Steering wheel adjustment 2. Opening handle, bonnet 3. Control panel, windows and door mirrors 4. Stalk switch, left 5. Lighting panel and fuel filler flap opener 6. Door handle and lock button 7. Indicator lamp, locking 8. Air vents, dashboard 9. Air vent for side window 10. Keypad, steering wheel, left 11. Horn and airbags 12. Combined instrument panel 13. Keypad, steering wheel, right 14. Stalk switch, right 15. Ignition switch 16.
02 Instruments and controls Overview, right-hand drive car 02 38
02 Instruments and controls Overview, right-hand drive car 1. Switch, roof control 2. Electrical socket and cigarette lighter 3. Parking brake 4. Control panel, windows and door mirrors 5. Glovebox 6. Door handle and lock button 7. Indicator lamp, locking 8. Air vent for side window 9. Air vents, dashboard 10. Climate control 11. Controls, car settings/audio system etc. 12. Display, car settings/audio system etc. 13. Switch, interior lighting, left-hand side 14. Switch, alarm detectors and deadlocks 15.
02 Instruments and controls Driver’s door control panel Driver’s door control panel 02 1. 2. 3. 4. 5.
02 Instruments and controls Combined instrument panel 02 1. 2. 3. 4. Speedometer. Direction indicators, left. Warning symbol. Information display – The display presents information or warning messages, outside temperature and the time. When the outside temperature is between +2 °C and –5 °C, a snowflake symbol appears on the display. This warns of icy roads. The outside temperature gauge may show a slightly high reading after the car has been stationary. 5. Information symbol. 6.
02 Instruments and controls Indicator and warning symbols Functionality check, symbols 02 Symbols in the centre of the All indicator and warning symbols1 illuminate when the ignition key is turned to position II before starting. This is to check that the symbols are working. When the engine starts, all the symbols should go out except the handbrake symbol, which extinguishes when the handbrake is released.
02 Instruments and controls Indicator and warning symbols Indicator symbols – left-hand side – Stop the car in a safe place and turn off the engine. – Restart the engine. – Drive to an authorised Volvo workshop to have the ABS checked if the symbol remains lit. 7. Low level in fuel tank This symbol lights when there are approximately 8 litres of usable fuel left in a petrol-engined car, or approximately 7 litres in a diesel-engined car. 02 3.
02 Instruments and controls Indicator and warning symbols Indicator symbols – right-hand side 02 2. Parking brake applied The lamp illuminates when the parking brake is applied. Always pull the parking brake lever to the end position. NOTE The lamp illuminates irrespective of how hard the parking brake is applied. 1. Indicator symbol for trailer This symbol flashes when the direction indicators are used and a trailer is coupled.
02 Instruments and controls Indicator and warning symbols – Stop the car in a safe place and turn off the engine. – Restart the engine. – If both symbols extinguish, continue driving. – If the symbols remain on, check the level in the brake fluid reservoir. See page 183. – If the brake fluid level is normal but the symbols are still lit, the car can be driven, with great care, to an authorised Volvo workshop to have the brake system checked.
02 Instruments and controls Information display Messages 02 When a warning or indicator symbol illuminates, a message appears on the information display. – Press the READ button (1). Switch between messages with the READ button. Fault messages are stored in the memory until the fault is rectified. NOTE If a warning message appears while you are using the trip computer, the message must be read (press READ) before the previous activity can be resumed.
02 Instruments and controls Electrical socket 12 V electrical socket Cigarette lighter (option) Activate the lighter by pushing in the button. The button pops out when the lighter is hot. Pull out the lighter and light a cigarette on the heated coils. 02 The electrical socket can be used for 12 V accessories, such as mobile phone chargers and coolers. The maximum current is 10 A. For the socket to supply current, the ignition key must be in at least position I.
02 Instruments and controls Lighting panel Headlamp levelling The load in the car changes the vertical alignment of the headlamp beam, which could dazzle oncoming motorists. Avoid this by adjusting the height of the beam. 02 – Turn the ignition key to position II. – Turn the headlamp control (2) to one of the end positions. – Roll the control (1) up or down respectively to raise or lower beam alignment. Cars with Bi-Xenon headlamps1 have automatic headlamp levelling, so there is no control (1).
02 Instruments and controls Lighting panel the day and can be controlled manually at night. – Roll the control up or down (3) for brighter or dimmer lighting. Enhanced display lighting To facilitate reading the odometer, trip meter, clock and outside temperature gauge, these illuminate when the car is unlocked and when the key is removed from the ignition switch. The displays extinguish when the car is locked.
02 Instruments and controls Left-hand stalk switch Stalk switch positions 02 Short flash sequence – Move the stalk switch up or down to position (1) and release. The direction indicators flash three times and the stalk switch returns to its home position. Switching, main and dipped beam The ignition key must be in position II for main beam to be switched on. – Turn the headlamp control clockwise to the end position, see page 48.
02 Instruments and controls Left-hand stalk switch Trip computer (option) Functions The trip computer displays the following information: • • • • • • AVERAGE SPEED ACTUAL SPEED MPH1 NOTE If a warning message interrupts while you are using the trip computer, this message must be acknowledged. Acknowledge by pressing the READ button (A) and revert to the trip computer function. AVERAGE KILOMETRES TO EMPTY TANK DSTC, see page 125 ACTUAL SPEED MPH1 Current speed is displayed in mph.
02 Instruments and controls Right-hand stalk switch Windscreen wipers 02 Single sweep Raise the stalk switch to make a single sweep. Intermittent wiping The delay between sweeps can be adjusted. Turn the thumbwheel (C) up for a shorter interval between sweeps. Turn it down to increase the delay. Continuous wiping The wipers sweep at normal speed. A. Windscreen and headlamp washers The wipers sweep at high speed. B. Rain sensor – On/Off C. Thumbwheel D.
02 Instruments and controls Right-hand stalk switch Rain sensor (option) The rain sensor is automatically deactivated when the key is removed from the ignition switch or five minutes after the ignition is switched off. 02 IMPORTANT At an automatic car wash: Deactivate the rain sensor by pressing the button (B) while the ignition key is in position I or II. Otherwise, the windscreen wipers could start swiping and become damaged.
02 Instruments and controls Cruise control (option) Activating Increasing or decreasing speed – Press 0 to disengage the cruise control temporarily. CRUISE will be shown on the combined instrument panel. The speed set earlier is stored in the memory. The cruise control is also temporarily disengaged when: 02 The controls for cruise control are to the left of the steering wheel. Setting the desired speed: – Press the CRUISE button. CRUISE is shown on the combined instrument panel.
02 Instruments and controls Steering wheel keypad (option) Button functions 02 The four buttons at the bottom of the steering wheel keypad control the radio and the phone. The function of a button depends on which system is active. The steering wheel keypad can be used to scroll between preset stations, change CD tracks and adjust the volume. Press and hold one of the arrow keys to fast forward/reverse or search for the next station. The phone must be switched on to adjust audio system settings.
02 Instruments and controls Steering wheel adjustment, hazard warning flashers Steering wheel adjustment Hazard warning flashers The steering wheel can be adjusted for both height and reach. Use the hazard warning flashers (all direction indicators flash) when the car is stopped where it could be a traffic hazard or obstruction. Press the button to activate the function. 02 – Pull the lever towards you to release the steering wheel. – Adjust the steering wheel to the position that suits you best.
02 Instruments and controls Parking brake, electrical socket Parking brake (handbrake) – If the vehicle rolls, the parking brake lever must be pulled more firmly. When parking a vehicle always put the gear selector in 1st gear (for manual transmission) or P (for automatic transmission). Electrical socket in the rear seat 02 Parking on a hill If the car is parked facing uphill; turn the wheels away from the kerb. If the car is parked facing downhill; turn the wheels toward the kerb.
02 Instruments and controls Power windows Operation 02 Driver’s door Closing of front windows is stopped if anything prevents their movement. The control on the passenger door is operated in the same way as on the driver’s door. Manual operation means that the window stops moving when its control has been released. During automatic operation the movement of the window continues after its control has been released. Operate the windows with caution.
02 Instruments and controls Rearview and door mirrors Interior rearview mirror Rearview mirror with compass (option on certain markets) Calibrating the compass 02 Bright light from behind could be reflected in the rearview mirror and dazzle the driver. Use dimming when disturbed by light from behind. Dipping 1. Control for dimming 2. Normal position 3. Dimmed position. Automatic dimming (option) Bright light from behind is automatically dimmed by the rearview mirror.
02 Instruments and controls Rearview and door mirrors 02 – Press the button (1) repeatedly until the number for the required magnetic zone (1–15 ) is shown, refer to the map of magnetic zones for the compass. – Wait until the display returns to showing the character C. – Following which, press and hold the button for 9 seconds and select L for lefthand drive cars and R for right-hand drive.
02 Instruments and controls Rearview and door mirrors Door mirrors Retractable power door mirrors (option) The mirrors can be retracted for parking and driving in narrow spaces. This can be done in ignition position I and II. Retracting the mirrors – Press the L and R button at the same time. – Release the buttons. The mirrors automatically stop in the fully retracted position. IMPORTANT The controls for adjusting the two door mirrors are at the front of the driver’s door armrest.
02 Instruments and controls Personal preferences 02 Possible settings Climate control settings Personal preferences can be set for some of the car’s functions: the locks, climate control and audio functions. For audio functions, see page 204. Auto blower adjust The fan speed can be set to AUTO mode in cars equipped with ECC: Control panel A. Display B. MENU C. EXIT D. ENTER E. Navigation Use The settings are shown on the display (A). Open the menu to enter settings: Control panel.
02 Instruments and controls Personal preferences Automatic locking – doors When the speed of the car exceeds 7 km/h the doors and boot lid can be locked automatically. This function can be turned On/ Off. Pulling the door handle twice unlocks and opens the doors from the inside. Home safe lighting Select the time the car’s lights should remain on when the left-hand stalk switch is pulled back after the ignition key has been removed. The following alternatives are available: 30/60/90 seconds.
General information on climate control ...................................................................................................... Electronic climate control, ECC ............................................................... Air distribution .......................................................................................... Fuel-driven heater (option) .......................................................................
CLIMATE CONTROL 03
03 Climate control General information on climate control 03 ECC/Air conditioning Refrigerant The car is equipped with electronic climate control (ECC). The climate control system controls the air conditioning (A/C) and the cooling, heating and dehumidifying of the air in the passenger compartment. The air conditioning system contains R134a refrigerant. This refrigerant contains no chlorine, which means that it is harmless to the ozone layer. The system must only be charged with R134a refrigerant.
03 Climate control General information on climate control Air vents in the dashboard ECC (option) Actual temperature The temperature you select corresponds to the physical experience with reference to factors such as air speed, humidity and solar radiation in and around the car. Condensation In warm weather, condensation from the air conditioning may drip under the car. This is normal. 03 Sensor location • The sun sensor is on the top side of the dashboard.
03 Climate control Electronic climate control, ECC Control panel 03 1. 2. 3. 4. 5. 6. 7. 8. 9. AUTO Fan Recirculation/Air quality system Defroster Air distribution AC ON/OFF Heated front left seat Heated front right seat Rear window and door mirror defrosters 10. Temperature selector 68 Functions 1. AUTO Automatically maintains a selected passenger compartment temperature by regulating heat, fan speed, recirculation and air distribution.
03 Climate control Electronic climate control, ECC NOTE If the knob is turned anticlockwise and the fan indication on the display goes out, the fan and the air conditioning are switched off. The display shows the fan symbol and OFF. 3. Recirculation Recirculation can be used to shut out bad air, exhaust fumes, etc. from the passenger compartment. The air in the passenger compartment is recirculated, i.e. no outside air is taken into the car when this function is activated.
03 Climate control Electronic climate control, ECC 5. Air distribution The airflow can be distributed to the windows, dashboard vents or floor by pressing the air distribution buttons. 03 A symbol on the display above the climate control panel and an illuminated light in the relevant button indicate which function has been selected. See the table on p. 71. 6. AC – ON/OFF ON: Air conditioning is on. It is controlled by the system’s AUTO function. This way, incoming air is cooled and dehumidified. OFF: Off.
03 Climate control Air distribution Air distribution Use: Air distribution Use: Air to windows. Some air flows to the dashboard air vents. The air is not recirculated. Air conditioning is always engaged. To remove ice and misting quickly. Air to the floor and windows. Some air flows to the dashboard air vents. To ensure comfortable conditions and good demisting in cold or humid weather. Air to windscreen and side windows. Some air flows to the dashboard air vents.
03 Climate control Fuel-driven heater (option) General information about heaters 03 Parking on a hill If the car is parked on a steep hill, the front of the car should point downhill to ensure that there is a supply of fuel to the parking heater. WARNING The car must be outdoors when the petrol or diesel heater is used. WARNING Switch off the fuel-driven heater before refuelling. Spilled fuel could be ignited. Check on the information display that the heater is off.
03 Climate control Fuel-driven heater (option) Immediate stop of heater Setting the TIMER AM and PM Clock/timer – Use the thumbwheel (B) to scroll to DIRECT START. – Press RESET (C) to access the options ON and OFF. – Select OFF. For safety reasons, you can only programme times for the following 24 hours, not several days in advance. If the car clock is reset after the heater timers are programmed, the selected times will be cancelled. – Scroll with the thumbwheel to TIMER.
Front seats ............................................................................................... 76 Electrically operated roof ......................................................................... 79 Wind deflector (option)............................................................................. 83 Wind deflector (option)............................................................................. 83 Interior lighting .......................................................................
INTERIOR 04
04 Interior Front seats Seating position The control (2) is not available for all seat models. WARNING Adjust the position of the driver’s seat before setting off, never while driving. Check that the seat is locked in position. Power seat Move the seat forward: – Move the handle (1) up to release the backrest. – Fold the backrest forward until it locks. – Press the button (2) located by the side of the head restraint. Keep it pressed in.
04 Interior Front seats Power seat (option) Memory function NOTE The seat can only be moved to the very front (+6 cm) to facilitate entry and exit to and from the rear seat when the backrest has been folded forward. If the backrest is folded back when the seat is in the front position then the seat automatically moves back approx. 6 cm after a few seconds. 04 WARNING Check that the backrest is properly folded back by pushing and pulling the head restraint.
04 Interior Front seats when the car has been locked with the remote control key. When the car is unlocked with the same remote control key the driver’s seat and the door mirrors adopt the stored positions when the driver’s door is opened. NOTE The key memory is independent of the seat memory. 04 Emergency stop If the seat accidentally begins to move, press any of the buttons to stop the function. WARNING Risk of crushing. Make sure that children do not play with the controls.
04 Interior Electrically operated roof Conditions for roof operation – No objects on the parcel shelf. – No ice, snow or loose objects on the roof or boot lid. – Dry roof. – 2.0 m clearance upward (A) and 0.2 m between bumper and objects behind (B). – Ambient temperature –10 °C or warmer. – Closed cargo separator, see page 90. – Closed boot lid. – Stationary car, brake pedal depressed.
04 Interior Electrically operated roof Hatch cover Opening and closing the roof WARNING Never pull the release wire for the hydraulic system that is located under the rear seat cushion. Only service personnel are allowed to use the hydraulic system’s emergency release function. Consequences: • significant risk of crushing injury • uncontrolled movement/opening of the electrically operated roof or boot lid • the roof components could be destroyed.
04 Interior Electrically operated roof • • • • is not closed. Close the cargo separator, see page 90. LOW BATTERY FOR ROOF OPERATION – The battery voltage is too low. The roof can only be closed. Charge the battery, e.g. by starting the engine, and try again. ROOF NOT LOCKED – The roof has not been opened or closed properly. Try again to open or close the roof. ROOF IN LOAD AID POSITION – The roof has been raised with the loading assistance function. Lower the roof, see page 90.
04 Interior Electrically operated roof Plastic cover for temporary covering – Secure the hooks (4) in the rear wheel arches and the hooks (6) under the rear bumper. 04 If the roof cannot be closed due to low battery voltage or a possible roof fault then a protective plastic cover can be fitted. The plastic cover is fitted with the rope attachments inward. The plastic cover is stored in a bag marked "Cover for temporary use". 82 Plastic cover, located in the ski hatch.
04 Interior Wind deflector (option) Wind deflector – Press the locking levers into the holders on the side panels until a click is heard. – Open out the wind deflector. The zips in the wind deflector are used for storing/retrieving luggage on the rear seat. WARNING Check that the wind deflector is secured firmly. Otherwise it may detach in the event of sudden movement for example and then cause injury and damage. 04 WARNING Wind deflector.
04 Interior Interior lighting Front seat lighting The reading lamps can be switched on in ignition position I and II as well as when the engine is running. They can also be activated within 30 minutes after the engine has been switched off or when one of the doors has been opened/closed. Rear seat lighting The passenger compartment lighting is switched on and off automatically when button (2) is in neutral position.
04 Interior Interior lighting Vanity mirror1 04 The light illuminates automatically when the cover is lifted. 1 Option on certain markets.
04 Interior Storage spaces in the passenger compartment 04 86
04 Interior Storage spaces in the passenger compartment Storage spaces 1. Storage compartment in door panel (lockable as option) 2. Coat hanger, only for light garments 3. Storage pocket on front edge of front seat cushions 4. Ticket clip 5. Glovebox 6. Storage compartment 7. Cup holder (with roller cover, option certain markets) 8. Tunnel compartment (e.g. for CD discs) 9. Cup holder (with roller cover, option) 10. Storage compartment in rear side panel 11.
04 Interior Storage spaces in the passenger compartment Storage compartment in door panel Storage compartment in rear side panel Cup holder, rear 04 The storage compartment is opened by lifting the lower front edge of the hatch, and closed with a touch on its upper section. Lockable storage compartment in door panel (option) The storage compartment is locked with the remote control, see page 98. 88 The storage compartment is opened and closed with a touch in the centre of its upper section.
04 Interior Storage spaces in the passenger compartment Tunnel compartment 04 Press the button located on the front of the cover to open and close the compartment. The compartment also includes manual opening of the boot lid using the key blade1, see page 104. 1 Alternatively the lock is located down at the floor behind the driver’s seat.
04 Interior Cargo area Cargo separator Loading assistance 04 The purpose of the separator is to limit the amount of the load in the cargo area so that the movement of the roof is not disrupted. Be sure to close the cargo separator fully so that it is locked on both the left and right-hand sides. IMPORTANT Do not place objects above or alongside the cargo separator when it is closed. Do not position luggage so that it is higher that the closed cargo separator. Decal on cargo separator.
04 Interior Cargo area Using loading assistance One press on the button both starts and stops raising/lowering. It may take several seconds before the movement starts. If a signal sounds when the button is pressed and the roof does not move, read the message on the information display. – Press the button to raise the roof. – Lift the cargo separator and move it into the cargo area. – When loading is complete, fold down the cargo separator. – Press the button so that the roof is lowered.
04 Interior Cargo area Ski hatch Open the centre section in the back of the rear seat – Pull the strap in the top of the backrest centre section to access the hatch. Close the centre section in the back of the rear seat – Refit the centre section with the lower part first. – Fold in the centre section and press until a clicking sound is heard. 04 There is a hatch behind the centre panel1 in the rear seat backrest for transporting long, light objects. Max. length: 2 m and max. weight: 25 kg.
04 Interior 04 93
Remote control with key blade ................................................................ 96 Service locking......................................................................................... 99 Battery in remote control ....................................................................... 101 Locking and unlocking ........................................................................... 102 Alarm (option)........................................................................................
LOCKS AND ALARM 05
05 Locks and alarm Remote control with key blade Remote control Loss of a remote control The car is supplied with two remote controls which also serve as ignition keys. The remote controls contain detachable metal key blades for mechanical locking/unlocking of the driver’s door and glovebox. If you lose a remote control, take the car and the other remote controls to an authorised Volvo workshop. The code of the missing remote control must be erased from the system as a theft prevention measure.
05 Locks and alarm Remote control with key blade position/parking lamps, number plate lighting and door mirror lamps (option). The lighting is switched off automatically after 30, 60 or 90 seconds. For time setting, see page 63. 4. Boot lid — Press the button once to unlock the boot lid only. NOTE The function does not open the boot lid. 5. Panic function — Used to attract attention in an emergency.
05 Locks and alarm Remote control with key blade Key blade 05 1. Active locks for remote control: 2. Active locks for remote control with lockable storage compartments: A. doors B. steering lock A. doors F ski hatch B. steering lock G. boot lid D. storage compartments in door panels F ski hatch G. boot lid For descriptions of the different storage areas, see page 87.
05 Locks and alarm Service locking 05 1. Central locking’s normal active locks with the remote control. 2. Remote control with activated service locking and removed key blade. Service locking function1 means that the remote control’s normal control of central locking is limited; the car’s lockable storage compartment’s are blocked and cannot be unlocked with the remote control. This can be desirable when the car is left for service for example.
05 Locks and alarm Service locking – Insert the key blade into the glovebox keyhole (C) and turn 180 degrees clockwise, see page 104. NOTE Do not reinsert the key blade into the remote control but keep it in a safe place instead. Following which, the lockable storage compartments behind the door panels (D), the ski hatch (E) and the boot lid (F) can no longer be unlocked with the remote control.
05 Locks and alarm Battery in remote control Weak remote control battery Replacing the remote control battery When the battery runs down and full functionality cannot be guaranteed, the information symbol illuminates and the REMOTE BATTERY LOW VOLTAGE appears on the display. – Refit the cover and screw it shut. – Press the key blade back into place. Dispose of the old battery in an environmentally-friendly way.
05 Locks and alarm Locking and unlocking Locking/unlocking the car from outside Unlocking The remote control unlock button can unlock the car in two different ways (select option in personal preferences, see page 63): 05 Be aware that you can be locked in the car if it is locked from the outside with the remote control. You cannot leave the car using any of the controls inside the car.
05 Locks and alarm Locking and unlocking Locking/unlocking the car from inside – Pull the handle twice to unlock and open the doors. Lock indicator 05 The doors and the boot lid can be locked or unlocked simultaneously using the lock button by the door handle. Unlocking – Press the upper section of the lock button. The door cannot be unlocked by pulling up the lock button. An LED on the inside of the door in question illuminates for approx.
05 Locks and alarm Locking and unlocking Opening the boot lid mechanically Variant 2 Locking the glovebox – Fold forward the left-hand seat’s backrest to access the keyhole down at the floor. – Insert the key blade and turn it clockwise 110 degrees. The glovebox can only be locked and unlocked with the removable key blade in the remote control. If the car’s electrical systems are temporarily out of order then the boot lid can be opened mechanically with the remote control’s detachable key blade.
05 Locks and alarm Locking and unlocking Deadlocks When deadlocked, the doors cannot be opened from the inside if they are locked. The deadlocks are activated with the remote control. The deadlocks are set after a 25 second delay after the doors are locked. Temporary deactivation of the deadlocks and any detectors If the car is equipped with an alarm, movement and tilt detectors are also deactivated. See page 106.
05 Locks and alarm Alarm (option) Alarm system Alarm light on instrument panel When the alarm is armed, it continually monitors all alarm inputs. NOTE The alarm is triggered if: 05 • a door, the bonnet or boot lid opens • a non-approved key is used in the ignition or if an attempt is made to force the lock. • a movement is detected in the passenger compartment (if fitted with a movement detector). • the car is raised or towed away (if fitted with a tilt detector). • a battery cable is disconnected.
05 Locks and alarm Alarm (option) Automatic alarm activation Remote control not working This function prevents you accidentally leaving the car without the alarm on. Testing the movement detector in the passenger compartment – Open all windows. – Arm the alarm. Arming the alarm is confirmed by the light flashing slowly. – Wait 30 seconds. – Test the movement detector in the passenger compartment, such as by lifting out a bag from a seat.
05 Locks and alarm Alarm (option) – Arm the alarm. Remain in the car and lock the doors with the button on the remote control. – Wait 30 seconds. – Open the bonnet with the handle under the dashboard. A siren should sound and all direction indicators flash. – Deactivate the alarm by unlocking the car with the remote control.
05 Locks and alarm 05 109
General................................................................................................... 112 Refuelling ............................................................................................... 114 Starting the engine................................................................................. 115 Diesel particle filter (DPF)....................................................................... 116 Ignition switch and steering lock................................................
STARTING AND DRIVING 06
06 Starting and driving General Economical driving Driving economically means driving smoothly while thinking ahead and adjusting your driving style and speed to the prevailing conditions. 06 • Get the engine warmed up as soon as possible. • Do not let the engine idle, but drive at light loads as soon as it is possible. • A cold engine consumes more fuel than a warm one. • Avoid braking too hard. • Do not drive with unnecessary loads in the car. • Do not use winter tyres when the roads are dry.
06 Starting and driving General Clean the electric contacts of the electric engine block heater and trailer coupling after driving in water and mud. IMPORTANT Do not let the car stand with water over the sills for any long period of time. This could cause electrical malfunctions. In the event of stalling in water, do not try to restart. Tow the car out of the water. Do not overload the battery The electrical functions in the car load the battery to varying degrees.
06 Starting and driving Refuelling Opening the fuel filler flap – Turn past the resistance until it comes to a stop. – Take out the cap. – Hang up the cap on the inside of the fuel filler flap. NOTE Put the petrol cap back after refuelling. Turn until one or more clear clicks are heard. Opening from the cargo area Remove the cover over the lamp housing on the right-hand side of the cargo area. Pull the cord hanging on the hook. When the fuel filler flap has opened, refit the cord and cover.
06 Starting and driving Starting the engine Petrol Before starting the engine Starting the engine – Apply the parking brake. IMPORTANT Do not add cleaning additives to the petrol, unless recommended by Volvo. Diesel At low temperatures (–5 °C to –40 °C), a paraffin precipitate may form in the diesel fuel, which can lead to ignition problems. Automatic gearbox – Gear selector in position P or N. Manual gearbox Put the gear lever in neutral and hold the clutch pedal fully depressed.
06 Starting and driving Diesel particle filter (DPF) Diesel particle filter (DPF)1 Diesel cars may be equipped with a particle filter, which results in more efficient emission control. The particles in the exhaust gases are collected in the filter during normal driving. So-called "regeneration" is started in order to burn away the particles and empty the filter. This requires the engine to have reached normal operating temperature.
06 Starting and driving Ignition switch and steering lock Ignition keys and electronic immobiliser The ignition key must not hang with other keys or metal objects on the same key ring. The electronic immobiliser could be activated accidentally. Ignition switch and steering lock 0 – Locked position The steering lock is activated when the key is removed from the lock. I – Radio position Certain electrical components can be switched on. The engine’s electrical system is not activated.
06 Starting and driving Manual gearbox 06 Gear positions, five-speed Reverse gear inhibitor, five-speed Gear positions, six-speed (petrol) Depress the clutch pedal fully with each gear change. Remove your foot from the clutch pedal between gear changes! Follow the appropriate shifting pattern. Only engage reverse gear when the car is stationary. To engage reverse gear, the gear lever must first be put in position N.
06 Starting and driving Manual gearbox Reverse gear inhibitor, six-speed (petrol) Only engage reverse gear when the car is stationary. NOTE Reverse gear is electronically blocked if the car is travelling faster than approx. 20 km/h. Gear positions, six-speed (diesel)1 Depress the clutch pedal completely for each gear change. Remove your foot from the clutch pedal between gear changes. Follow the indicated gear pattern. For optimum fuel economy use the highest possible gear as often as possible.
06 Starting and driving Automatic gearbox Cold start Safety systems When starting in low temperatures, the gear changes can sometimes feel hard. This is due to the gearbox oil’s viscosity at low temperatures. To minimise engine emissions, the gearbox shifts up later than normal when the engine is started at low temperatures. Cars with an automatic gearbox have special safety systems: pedal must be depressed and the ignition key must be in position II.
06 Starting and driving Automatic gearbox Mechanical gear selector inhibitor Automatic gear positions The gearbox is mechanically blocked when P position is engaged. Always apply the parking brake when parking the car. R – Reverse The car must be stationary when R is selected. N – Neutral N is the neutral position. No gear is engaged and the engine can be started. Apply the parking brake when the car is stationary with the gear selector in position N.
06 Starting and driving Automatic gearbox Manual positions To move from the automatic driving position D to a manual position, move the gear selector to position M. To go from position M to the automatic driving position D, move the selector to position D. While driving The manual gearshift mode can be selected at any time while driving. The engaged gear is locked until you choose another gear.
06 Starting and driving Brake system Brake servo If the car is rolling or is being towed with the engine turned off, the brake pedal must be pressed about five times harder than when the engine is running. If the brake pedal is pressed when the engine is started, you will feel the pedal drop. This is normal and due to the brake servo becoming active. This may be more noticeable if the car has emergency brake assistance (EBA). WARNING The brake servo only works when the engine is running.
06 Starting and driving Brake system Emergency brake assistance – EBA (Emergency brake assistance) In case of sudden braking, full-strength braking is provided instantaneously. The EBA function senses when heavy braking is underway by registering how quickly the brake pedal is depressed. Continue braking without easing off on the brake pedal. The function is suspended when the pressure on the brake pedal eases. This function is always active and cannot be disengaged.
06 Starting and driving Stability and traction control system General Reduced operation The Dynamic Stability and Traction Control system DSTC improves the car’s traction and helps the driver to avoid skidding. DSTC SPIN CONTROL OFF means that system operation is reduced. – Press and hold RESET (B) until the DSTC menu is changed. At the same time the symbol illuminates as a reminder that the system has been reduced. The system remains reduced until the engine is next started.
06 Starting and driving Stability and traction control system Messages in the information display TRACTION CONTROL TEMPORARILY OFF means that the system has been temporarily reduced due to excessive brake disc temperature. The function is reactivated automatically when the brakes have cooled. Symbols in the combined instrument panel DSTC system Information ANTI-SKID SERVICE REQUIRED means that the system has been disabled due to a fault. – Stop the car in a safe place and turn off the engine.
06 Starting and driving Parking assistance (option) General1 Function The system is activated automatically when the car is started and the text message Park Assist active, Exit to deactivate is shown on the audio system display. Parking assistance is active at speeds below 15 km/h. The system is deactivated at higher speeds. The system is reactivated when the speed falls below 10 km/h again. The frequency of the signal increases as you come closer to an object in front of or behind the car.
06 Starting and driving Parking assistance (option) Activating/deactivating Parking assistance can be deactivated by pressing EXIT on the control panel, see page 62. Park Assist deactivated Enter to activate will appear on the audio system display. Cleaning the sensors Parking assistance can be reactivated by pressing ENTER on the control panel. Park Assist active Exit to deactivate will then appear on the display. Parking assistance sensors.
06 Starting and driving Towing and recovery Never tow the car to bump start it Jump start the car with a donor battery if the battery is flat and the engine does not start. Do not bump start the car. IMPORTANT Bump starting the car can damage the catalytic converter. Towing Find out the highest legal speed for towing before towing the car. – Turn the ignition switch to position II and unlock the steering lock so that the car can be steered, see page 117.
06 Starting and driving Towing and recovery Towing eye 06 130 Use the towing eye if the car needs to be towed on the road. The towing eye is attached in the recess on the right-hand side of the front or rear bumper. To fit the towing eye: – After use, unscrew the towing eye and return it in the cargo area. Refit the cover on the bumper. – Take out the towing eye which is located in the bag in the ski hatch or together with the spare wheel.
06 Starting and driving Jump starting Starting with a donor battery – – – – – If the battery in the car has become flat, you can "borrow" electric current from either a separate battery or the battery in another car. Always make sure the crocodile clips on the jump leads are attached securely to eliminate sparks during the start attempt. When jump starting the car, the following steps are recommended to avoid risk of explosion: – ensure that the cars do not touch one another.
06 Starting and driving Driving with a trailer General The load capacity is affected by extra accessories mounted on the car, such as a towbar, load carriers, space box, the passengers’ combined weight etc. as well as towball load. The load capacity of the car is reduced by the number of passengers and their weight. If the towing bracket is fitted by an authorised Volvo workshop, then the car is delivered with the necessary equipment for driving with a trailer.
06 Starting and driving Driving with a trailer Automatic gearbox, driving with a trailer Diesel engine with manual gearbox, driving with a trailer Parking on a hill – Apply the parking brake (handbrake). – Move the gear selector to parking position P. If the car is driven with a major load in a hot climate, the engine cooling fan can be replaced with one of a greater capacity than the standard model. Check with your nearest Volvo dealer regarding the options for your car.
06 Starting and driving Towing equipment Towbars Trailer cable The towball must be cleaned and greased regularly. If a towball hitch with vibration damper is used, it is not necessary to grease the towball. If the car is equipped with a detachable towbar, the towball mounting instructions must be followed carefully, see page 136. WARNING Be sure to attach the trailer’s safety cable to the correct place.
06 Starting and driving Towing equipment Specifications Dimensions for mounting points (mm) Fixed or detachable towbar A B C D E F G H I J K 1147 68 964 482 40 141 538 150 113 100 140 1 Side member 2 Ball centre 06 135
06 Starting and driving Detachable towbar Fitting the towball – Remove the guard plug. 06 136 – Ensure that the mechanism is in the unlocked position by turning the key clockwise. – Check that the indicator window (3) shows red. If the window does not show red, press in (1) and turn the locking wheel anticlockwise (2) until you hear a click.
06 Starting and driving Detachable towbar – Insert the towball section until you hear a click. – Check that the indicator window shows green. – Turn the key anticlockwise to the locked position. Remove the key from the lock.
06 Starting and driving Detachable towbar NOTE 06 138 Check that the towball section is secure by pulling it up, down and back. If the towball section is not fitted correctly then it must be removed and refitted in accordance with the previous steps NOTE The trailer’s safety cable must be attached to the attachment on the towbar.
06 Starting and driving Detachable towbar Removing the towball – Insert the key and turn it clockwise to the unlocked position. – Push in the locking wheel (1) and turn it anticlockwise (2) until you hear a click. – Turn the locking wheel down fully, until it comes to a stop. Hold it in this position while pulling the towball rearward and upward.
06 Starting and driving Detachable towbar – Insert the guard plug.
06 Starting and driving Loading General The load capacity is affected by extra accessories mounted on the car, such as a towbar, the passengers’ combined weight etc. as well as towball load. The load capacity of the car is reduced by the number of passengers and their weight. For information on permitted weights, see page 229. • Secure all loads to the load retaining eyelets with straps or web lashings.
06 Starting and driving Adjusting headlamp pattern Correct light pattern for left or righthand traffic A. Headlamp pattern for left-hand traffic. B. Right-hand traffic. 06 142 The headlamps’ projection can be adjusted to avoid dazzling other motorists. The correct pattern will also better illuminate the verge. Halogen headlamps Bi-Xenon headlamps The headlamp control should be in position (A) for left-hand traffic and position (B) for right-hand traffic.
06 Starting and driving 06 143
General................................................................................................... 146 Tyre pressure .......................................................................................... 150 Warning triangle and spare wheel.......................................................... 152 Changing wheels.................................................................................... 154 Emergency puncture repair ...................................................................
WHEELS AND TYRES 07
07 Wheels and tyres General Driving characteristics and tyres Speed ratings New tyres The tyres greatly affect the car’s driving characteristics. The type of tyre, dimensions, tyre pressure and speed rating are important for how the car performs. The car has "Whole Vehicle Type Approval", which means that dimensions and speed ratings must not differ from those specified on the vehicle’s registration document.
07 Wheels and tyres General More even wear and maintenance Tyres with tread wear indicators Tread wear indicators are narrow treadless bands across the width of the tread. On the side of the tyre are the letters TWI (Tread Wear Indicator). When the tyre’s tread depth is down to 1.6 mm, the tread depth will be level in height with the tread wear indicators. Change to new tyres as soon as possible. Remember that tyres with little tread depth provide very poor grip in rain and snow.
07 Wheels and tyres General Rims and wheel nuts Steel rims – standard wheel nuts (1) Steel rims are normally mounted with the standard wheel nuts, but the bulge acorn variety may also be used. WARNING Never use standard nuts for aluminium rims. The wheels can come loose. Spare wheel Temporary Spare The spare wheel1 is only intended to be used for the short time it takes to get the normal wheel replaced or repaired. Replace the spare wheel as soon as possible with a normal wheel.
07 Wheels and tyres General Summer and winter wheels and capacity to force rain, snow and slush out of the way are adversely affected. Tyres with the greatest tread depth should always be fitted to the rear of the car (to decrease the risk of skidding). Wheels should be stored lying down or hanging up, and not standing up. Contact an authorised Volvo workshop if you are uncertain about tread depth.
07 Wheels and tyres Tyre pressure Recommended tyre pressure Checking the tyre pressure Check the tyre pressure regularly. NOTE Tyre pressure decreases over time, this is a natural phenomenon. Tyre pressure also varies depending on ambient temperature. The tyre pressure label on the driver’s side door pillar shows which pressures the tyres should have at different loads and speed conditions. NOTE 07 Full load in the car equates to the number of seats with seatbelts.
07 Wheels and tyres Tyre pressure Tyre pressure table Variant Tyre size Speed (km/h) 2.4 2.
07 Wheels and tyres Warning triangle and spare wheel Warning triangle Follow the regulations for the use of a warning triangle1. Place the warning triangle in a suitable place with regard to the traffic. 07 – Undo the case containing the warning triangle, it is attached with Velcro. Take the warning triangle out of the case. – Lower the warning triangle’s support legs. Ensure the warning triangle and its case are located in the spare wheel well. 1 152 Certain markets.
07 Wheels and tyres Warning triangle and spare wheel Spare wheel and tools Spare wheel and tools The spare wheel1 is supplied in a tyre bag that is located in the cargo area spare wheel well. In the centre of the tyre is a black foam block containing jack and wheel bolt key. The tensioning strap for the bag is secured in two lashing eyes on the floor. – Undo the two tensioning straps that secure the tyre bag to the floor. – Unzip the tyre bag and take out the tools. – Lift the spare wheel from the bag.
07 Wheels and tyres Changing wheels Removing wheels Set up the warning triangle if a wheel must be replaced at a busy location. Make sure that the car and jack are on a firm horizontal surface. 07 154 – Take out the spare wheel, jack and wheel wrench, which are found under the carpet in the cargo area. – Apply the parking brake and engage first gear, or position P if the car has an automatic gearbox. – Place chocks in front of and behind the wheels which will remain on the ground.
07 Wheels and tyres Changing wheels Fitting the wheel – Clean the contact surfaces on the wheel and hub. – Put on the wheel. Tighten the wheel nuts. – Lower the car so that the wheel cannot rotate. – Tighten the wheel nuts crosswise. It is important that the wheel nuts are tightened properly. Tighten to 90 Nm. Check the torque with a torque wrench. – Put on the wheel cover (steel rim). WARNING Never crawl under the car when it is raised on the jack.
07 Wheels and tyres Emergency puncture repair General NOTE The car can be supplied with two different types of emergency puncture repair kit. They are each described individually and are named variant 1 and variant 2 12 V sockets for the compressor are located by the centre console in the front, by the rear seat and in the cargo area. Choose the electrical socket that is nearest the punctured tyre.
07 Wheels and tyres Emergency puncture repair Variant 1 Inflating tyres Set up the warning triangle if a tyre must be inflated in an area close to traffic. – Ensure that the orange switch (2) is in position 0 and take out the lead (5) and air hose (4) from the side compartment (3). – Screw the air hose’s valve connection to the bottom of the thread on the tyre’s air valve. – Connect the lead (5) to one of the car’s 12 V sockets. – Start the engine. The car must be in a wellventilated place.
07 Wheels and tyres Emergency puncture repair Sealing punctured tyres Set up the warning triangle if emergency tyre repairs must be carried out in an area where there is other traffic. 07 158 – Remove the decal (1) regarding the highest permitted speed from the emergency puncture repair kit and stick it on the steering wheel where it can be clearly seen by the driver. – Ensure that the orange switch (2) is in position 0 and take out the lead (5) and air hose (4) from the side compartment (3).
07 Wheels and tyres Emergency puncture repair WARNING Never stand next to the tyre when the compressor is running. Be particularly observant of the tyre walls. If cracks, irregularities or other damage appears, turn off the compressor immediately. Under these circumstances your journey should not continue. Contact an authorised tyre centre. – Undo the air hose (4) from the air valve and put the valve’s dust cap back on. Unplug the lead (5) from the electrical socket.
07 Wheels and tyres Emergency puncture repair Changing the sealing fluid canister The canister of sealing fluid should be changed before the best-before date has expired, see date label (1), or after the tyre has been sealed. After use, the canister (6) with holder (8) and air hose (10) should be changed. 07 This change can be carried out by an authorised Volvo workshop or following the instructions. IMPORTANT Read the safety instructions on the bottom of the canister.
07 Wheels and tyres Emergency puncture repair Changing the canister and hose after use – Undo the two screws (2) on the orangecoloured case (3). – Remove the speed label (4) and date label (1), and open the safety catch (5). Loosen the case (3) and take it off. – Push down the button (8) while turning the canister (6) and the holder (9) clockwise. Remove them. – Pull out the air hose (10). – Wipe off remaining sealing fluid with a rag or scrape it away if it is has already dried. – Fit a new air hose (10).
07 Wheels and tyres Emergency puncture repair Variant 2 Overview 7. Air hose 8. Sealing fluid bottle 9. Pressure gauge 10. Gloves Inflating the tyres The car’s original tyres can be inflated by the compressor. – The compressor must be switched off. Make sure that the switch is in position 0 and locate the cable and air hose. – Unscrew the wheel’s dust cap and screw in the air hose valve connection to the bottom of the thread on the tyre’s air valve.
07 Wheels and tyres Emergency puncture repair Sealing punctured tyres – Put on the gloves. WARNING The sealing fluid can irritate the skin. In the case of contact with skin, wash away the fluid with soap and water. – Unscrew the orange cap and unscrew the bottle’s stopper. NOTE Do not break the bottle seal. The seal is broken when the bottle is screwed in. WARNING Never stand next to the tyre when the compressor is running.
07 Wheels and tyres Emergency puncture repair – Switch off the compressor and unplug the cable from the 12 V socket. – Detach the hose from the tyre’s air valve and fit the valve’s dust cap. – As soon as possible, drive approximately 3 km at a maximum speed of 80 km/h so that the sealing fluid can seal the tyre. Rechecking the repair and pressure – Reconnect the equipment. – Read the tyre pressure on the pressure gauge. – If it is below 1.3 bar then the tyre is insufficiently sealed.
07 Wheels and tyres 07 165
Cleaning ................................................................................................. 168 Touching up paintwork ........................................................................... 171 Rustproofing ..........................................................................................
CAR CARE 08
08 Car care Cleaning Washing the car Wash the car as soon as it becomes dirty. Use car shampoo. Dirt and road salt can lead to corrosion. • Do not park the car in direct sunshine. Washing a car with hot paintwork can cause permanent paintwork damage. Wash the car in a car wash with waste water separator. • Thoroughly rinse dirt off the underbody of the car. • Rinse the entire car to remove loose dirt.
08 Car care Cleaning Polishing and waxing Polish and wax the car if the paintwork is dull or to give the paintwork extra protection. The car does not need to be polished until it is at least one year old. However, the car can be waxed during this time. Do not polish or wax the car in direct sunlight. Wash and dry the car thoroughly before you begin polishing or waxing. Clean off asphalt and tar stains using Volvo tar remover or white spirit.
08 Car care Cleaning – The leather has now been given improved protection against stains and a UV filter. Treating stains on interior plastic parts and surfaces A special cleaning agent, available from Volvo dealers, is recommended for cleaning interior plastic parts and surfaces. Do not scrape or rub stains. Never use strong stain removers. Cleaning seatbelts Use water and a synthetic detergent. A special textile cleaning agent is available from your Volvo dealer.
08 Car care Touching up paintwork Paintwork Stone chips and scratches Paint is an important part of the car’s rustproofing and should therefore be checked regularly. To avoid the onset of rust, damaged paintwork must be rectified immediately. The most common types of paintwork damage are stone chips, scratches, and marks on the edges of wings and doors. Colour code Before touching up paintwork, the car must be clean and dry and at a temperature above 15 °C.
08 Car care Rustproofing Inspection and maintenance Your car received a thorough and complete rustproofing at the factory. Parts of the body are made of galvanised sheet metal. The underbody is protected by a wear-resistant anti-corrosion compound. And, a thin, penetrating rustproofing fluid was sprayed into the members, cavities and closed sections. Maintain the car’s rustproofing. • Keep the car clean. Hose down the underbody.
08 Car care 08 173
Volvo service .......................................................................................... 176 Self-maintenance ................................................................................... 177 Bonnet and engine compartment .......................................................... 178 Diesel ..................................................................................................... 179 Oils and fluids ............................................................................
MAINTENANCE AND SERVICE 09
09 Maintenance and service 09 Volvo service Volvo service programme Installing accessories Before the car left the factory, it was thoroughly test driven. It was checked again in accordance with Volvo Car Corporation regulations before it was handed over to you. The incorrect connection and installation of accessories can negatively affect the car’s electrical system. Certain accessories only function when the appropriate software has been programmed into the car’s electrical system.
09 Maintenance and service Self-maintenance Before starting work on the car Battery Check that the battery cables are correctly connected and tightened. Never disconnect the battery when the engine is running (e.g. if replacing the battery). Never use a quick charger to charge the battery. The battery cables must be disconnected when charging the battery. The battery contains acid that is both corrosive and toxic. Handle the battery in an environmentally-suitable way. Let your Volvo dealer assist you.
09 Maintenance and service 09 Bonnet and engine compartment Opening the bonnet – Pull the handle on the far left under the dashboard. You will hear when the catch releases. – Insert your hand under the centre of the front edge of the bonnet and press the safety catch to the right. – Open the bonnet. WARNING Check that the bonnet locks properly when closed. Engine compartment 1. Washer fluid reservoir (4-cyl.) 2. Coolant expansion tank 3.
09 Maintenance and service Diesel Fuel system Diesel must fulfil the EN 590 or JIS K2204 standards. Diesel engines are sensitive to contaminants, such as high volumes of sulphur particles for example. Only use diesel fuel from a well-known producers. Never use diesel of dubious quality. At low temperatures (–40 °C to –6 °C), a paraffin precipitate may form in the diesel fuel, which can lead to ignition problems.
09 Maintenance and service 09 Oils and fluids Engine compartment decal for oil grade Checking the engine oil and oil filter Volvo recommends oil products. Change the oil and oil filter in accordance with the intervals specified in the Service and Warranty Booklet. IMPORTANT Dipstick, petrol engines IMPORTANT Always use oil of the prescribed grade, see the engine compartment decal. Check the oil level frequently and change the oil regularly.
09 Maintenance and service Oils and fluids display texts. Certain models have both variants. Contact an authorised Volvo dealer for more information. Checking the oil Checking the oil level in a new car is especially important before the first scheduled oil change. The Service and Warranty Booklet specifies the odometer readings for oil changes. Volvo recommends checking the oil level every 2 500 km. The most accurate measurements are made on a cold engine before starting.
09 Maintenance and service Oils and fluids 09 Washer fluid, topping up NOTE Checking and topping up the coolant Mix the washer antifreeze and water before filling the reservoir. Location of washer fluid reservoir1. The windscreen and headlamp washers share a common reservoir. – Filler cap on 4-cylinder engines and diesel. – Filler cap on 5-cylinder engines. Add washer antifreeze during the winter so that the fluid does not freeze in the pump, reservoir and hoses. See the capacities on page 234.
09 Maintenance and service Oils and fluids Check the coolant regularly The level should lie between the MIN and MAX marks on the expansion tank. If the system is not filled sufficiently, high local temperatures could occur, causing a risk of damage (cracks) in the cylinder head. Top up the coolant when the level falls to the MIN mark.
09 Maintenance and service 09 Oils and fluids Checking and topping up the power steering fluid NOTE Check the level frequently. The fluid does not require changing. For capacities and recommended fluid grade, see page 234. If a fault should arise in the power steering system or if the car is without power and must be towed, it can still be steered. However the steering will be much heavier than normal and it will require more effort to turn the wheel.
09 Maintenance and service Wiper blades 09 Changing the wiper blades NOTE The wiper blades are different lengths. The blade on the driver’s side is longer than the blade on the passenger side. – Turn up the wiper arm. – Press the button located on the wiper blade mounting and pull straight out (1), parallel with the wiper arm. – Slide in (2) the new wiper blade until a "click" is heard. – Check (3) that the blade is firmly installed. – Fold down the wiper arm.
09 Maintenance and service 09 Battery Battery care WARNING Batteries can generate oxyhydrogen gas, which is highly explosive. A spark, which can be generated if you connect the jump leads incorrectly, is sufficient to make the battery explode. The battery also contains sulphuric acid, which can cause serious burns. If the acid comes into contact with eyes, skin or clothing, flush with large quantities of water. If acid splashes into the eyes, seek medical advice immediately.
09 Maintenance and service Battery Symbols on the battery Risk of explosion. 09 Changing the battery Use protective goggles Further information in the owner’s manual. Store the battery out of the reach of children. The battery contains corrosive acid. Avoid sparks and naked flames. Removing the battery – Switch off the ignition and remove the key. – Wait at least 5 minutes before touching any electrical terminals.
09 Maintenance and service 09 Replacing bulbs General Changing front bulbs All bulb specifications are given on page 239.
09 Maintenance and service Replacing bulbs Dipped beam Removing the cover and bulb: – Remove the entire lamp housing. – Bend aside the catches and remove the cover. – Unplug the connector from the bulb. – Release the spring clip that secures the bulb. First, press it to the left to release it, then out and down. – Pull out the bulb. – Refit the lamp housing. 09 Main beam Fitting a new bulb – Fit the new bulb. It can only be fitted in one position.
09 Maintenance and service 09 190 Replacing bulbs Position/parking lamps Direction indicators Side marker lamps – Pull out the bulb holder with a pair of pliers. Do not pull out the bulb holder by pulling the electrical cable. – Replace the bulb. – Press the bulb holder back into place. It can only be fitted in one way. – Twist the bulb holder anticlockwise and remove it. – To remove the bulb from the bulb holder, press the bulb in and turn it anticlockwise.
09 Maintenance and service Replacing bulbs Fog lamps Removing the bulb holder – Switch off all lights and turn the ignition key to position 0. – Remove the panel from around the lamp housing. – Remove the two Torx screws securing the lamp housing and take out the lamp housing. – Unplug the connector from the bulb. – Turn the bulb anticlockwise and pull it out. – Fit the new bulb and turn it clockwise. – Plug in the connector to the bulb.
09 Maintenance and service 09 192 Replacing bulbs Number plate lighting Courtesy lighting Cargo area – Switch off all lights and turn the ignition key to position 0. – Remove the screws with a screwdriver. – Detach the lens carefully. – Replace the bulb. – Refit and screw in the lens. – There is courtesy lighting under the dashboard on the driver and passenger sides. – Insert a screwdriver and gently turn so that the lens detaches. – Remove the blown bulb. – Fit a new bulb. – Refit the lens.
09 Maintenance and service Replacing bulbs Vanity mirror lighting Removing the mirror glass: – Insert a screwdriver underneath the lower edge, in the centre. Carefully prise up the lug on the edge. – Insert the screwdriver under the edge on both the left and right side (at the black rubber points) and carefully prise so that the lens releases at the lower edge. – Carefully detach and lift aside the entire mirror glass and cover. – Remove the blown bulb and replace it with a new one.
09 Maintenance and service 09 Fuses General Changing All electrical functions and components are fused to protect the car’s electrical system from damage by short circuiting and overloading. If an electrical component or function does not work, it may be because the component’s fuse was temporarily overloaded and blew. The fuses are in two different locations in the car: – Look in the fuse diagram to locate the fuse. – Pull out the fuse and check from the side to see whether the curved wire has blown.
09 Maintenance and service Fuses 09 Relay/fuse box in the engine compartment The fuse box has 36 fuse positions. Be sure to replace a blown fuse with a new fuse of the same colour and amperage. • 19—36 are of the "Mini Fuse" type. • Fuses 7—18 are of the "JCASE" type and should be replaced by an authorised Volvo workshop. • Fuses 1—6 are of the "Midi Fuse" type and may only be replaced by an authorised Volvo workshop. On the inside of the cover are tweezers to assist removing and fitting fuses.
09 Maintenance and service 09 Fuses 1. Radiator fan .............................................................................. 50 A 2. Power steering .................................................................. 80 A 3. Supply to passenger compartment fuse box ...................... 60 A 4. Supply to passenger compartment fuse box ...................... 60 A 5. Climate control element, additional heater PTC (option) ..... 80 A 6. Glow plugs (diesel) ...............................................
09 Maintenance and service Fuses 09 25. Reserve ...................................................................................26. Ignition switch ................................................................... 15 A 27. A/C compressor ................................................................ 10 A 28. Reserve ...................................................................................29. Front fog lamp ................................................................... 15 A 30.
09 Maintenance and service 09 Fuses Relay/fuse box in the passenger compartment The fuse box has 50 fuse positions. The fuses are located under the glovebox. The box also provides space for several spare fuses. Tools for fuse replacement are located in the relay/fuse box in the engine compartment, see page 195. Changing fuses – Remove the trim concealing the fuse box by pressing in the pin in the centre of the clips (1) about one cm and then withdrawing the clips.
09 Maintenance and service Fuses 37. Reserve ...................................................................................38. Reserve ...................................................................................39. Reserve ...................................................................................40. Reserve ...................................................................................41. Reserve ...................................................................................42.
09 Maintenance and service 09 Fuses 60. Seat heating (driver’s side)................................................. 15 A 61. Seat heating (passenger side) ............................................ 15 A 62. Reserve .................................................................................. 63. Supply, power window, right rear....................................... 20 A 64. LED for door lock, RTI ......................................................... 5 A 65. Infotainment system ...............
09 Maintenance and service 09 201
General................................................................................................... 204 Audio functions ...................................................................................... 205 Radio functions ...................................................................................... 207 CD functions .......................................................................................... 211 Menu structure – audio system..................................................
INFOTAINMENT SYSTEM 10
10 Infotainment system General Infotainment system 10 to be active until the key is removed from the ignition switch. The audio system is then started automatically the next time the key is turned to position I. Menus Some infotainment system functions are controlled via a menu system. The current menu level is shown at the top right of the display. Menu options are shown in the middle of the display. Infotainment is a system that integrates the audio system and the phone1.
10 Infotainment system Audio functions Audio controls Audio source selection Repeatedly pressing AM/FM switches between FM1, FM2 and AM. Repeatedly pressing MODE switches between CD and AUX. AUX1 The AUX input can be used for connecting an MP3 player for example. Sometimes the AUX external audio source can be heard at a different volume to the internal audio sources, e.g. the CD player. If the audio volume of the external audio source is too high then the sound quality can be impaired.
10 Infotainment system Audio functions 10 • CENTRE 1 – Centre speaker level. Three channel stereo or Pro Logic II must be activated before adjustment is possible. See page 206. • SURROUND 1 – Surround sound level. Pro Logic II must be activated before adjustment is possible. See page 206. Activating/deactivating the subwoofer – Press MENU and then ENTER. – Scroll to Audio settings and press ENTER. – Scroll to Subwoofer and press ENTER.
10 Infotainment system Radio functions Radio controls Manual tuning – Select wavelength using AM/FM (1). – Adjust the frequency by turning TUNING (3). Tune into a station with a long press (left or right) on the navigation button or by using the steering wheel keypad: – Hold the right or left side of the navigation button depressed until the desired frequency appears on the display.
10 Infotainment system Radio functions 10 Storing autostored presets in another memory An autostored preset can be transferred to the FM or AM memory. – Briefly press AUTO (7). Auto appears on the display. – Press a preset button. – Press the button under which the station will be stored and hold it depressed until the message Station stored appears on the display. The radio exits Auto mode and the stored station can be selected as a preset.
10 Infotainment system Radio functions Activating/deactivating TP – Press MENU and then ENTER. – Scroll to TP and press ENTER. TP from current station/all stations The radio can interrupt with traffic information from only the set (current) station or from all stations. – Select an FM station. – Press MENU and then ENTER. – Scroll to Advanced radio settings and press ENTER. – Scroll to TP and press ENTER. – Scroll to TP Station and press ENTER.
10 Infotainment system Radio functions Display of programme type 10 The programme type of the current station can be shown on the display. NOTE Not all radio stations support this function. Activating/deactivating display – Press MENU and then ENTER. – Scroll to PTY and press ENTER. – Scroll to Show PTY and press ENTER. Activating/deactivating AF – Press MENU and then ENTER. – Scroll to Advanced radio settings and press ENTER. – Scroll to AF and press ENTER.
10 Infotainment system CD functions CD function controls Starting playback (CD changer) If a CD position with a music CD is already selected when the audio system is activated then playback starts automatically. Otherwise change to CD changer mode using MODE and select a disc with the number buttons 1–6 or Up/Down on the navigation button. Inserting a CD (CD changer) – Select an empty position with buttons 1–6 or Up/Down on the navigation button. An empty position is marked on the display.
10 Infotainment system CD functions 10 automatically when all files in the current directory have been played back. Press left/right on the navigation button if the display is not wide enough to show the whole audio file name. Fast-wind/change CD tracks and audio files Short presses right/left on the navigation button are used to scroll between CD tracks/ audio files. Long presses are used to fastwind CD tracks/audio files. TUNING (or the steering wheel keypad) can also be used for this purpose.
10 Infotainment system Menu structure – audio system FM menu 1. News 2. TP 3. PTY 4. Radio text 5. Advanced radio settings 2. News 3. TP 4. Audio settings1 10 6. Audio settings1 AM menu 1. Audio settings1 CD menu 1. Random 2. News 3. TP 4. Disc text 5. Audio settings1 CD changer menu 1. Random 2. News 3. TP 4. Disc text 5. Audio settings1 AUX menu 1. AUX volume 1 Certain audio systems.
10 Infotainment system Phone functions (option) 10 Phone system components 214
10 Infotainment system Phone functions (option) Phone system components Emergency calls 1. Antenna Emergency calls to alarm centres can be made without a SIM card as long as there is coverage by a GSM operator. 2. Steering wheel keypad (option) Most phone system functions can be accessed via the keypad. See page 216. 3. Microphone The handsfree microphone is integrated in the roof console beside the rearview mirror. 4.
10 Infotainment system Phone functions (option) 10 – Pull out the SIM card holder (1) in the SIM card reader. – Position the SIM card in the holder with the metal surface visible. The bevelled edge of the SIM card should align with the bevel of the SIM card holder. – Carefully press in the SIM card holder. Phone controls Steering wheel keypad Menus Page 204 describes how to control phone functions with the menu system.
10 Infotainment system Phone functions (option) On/Off A handset appears on the display when the phone system is active or in standby mode. If the ignition key is turned to position 0 when the phone is in one of these modes, the phone automatically resumes this mode the next time the key is turned to position I or II. Activating the phone system Phone system functions can only be used when the phone is in active mode. – Press PHONE. – Enter the PIN code (if necessary) and press ENTER.
10 Infotainment system Phone functions (option) Volume 10 The phone uses the driver’s door or centre speaker1. Call volume Call volume is regulated with the buttons of the steering wheel keypad. If the privacy handset is used, volume is regulated with a wheel on the side of the handset. Audio system volume Audio system volume is temporarily lowered during a phone call. Once the call is ended the previous volume is resumed.
10 Infotainment system Phone functions (option) – Scroll to Search and press ENTER. – Enter the first few letters of the item and press ENTER, or simply press ENTER. – Scroll to an item and press ENTER. Speed dial A keypad button (1- 9) can be used as a speed dial number for a contact in the phone book. Copying entries between the SIM card and Phone book – Press MENU. – Scroll to Phone book and press ENTER. – Scroll to Copy all and press ENTER. – Scroll to SIM to phone or Phone to SIM and press ENTER.
10 Infotainment system Phone functions (option) • Swap – Switch between two calls (available if up to three parties are connected). 10 SMS – Short Message Service Reading SMS – Press MENU. – Scroll to Messages and press ENTER. – Scroll to Read and press ENTER. – Scroll to a message and press ENTER. The message text appears in the display. Additional selections can be made by pressing ENTER. Hold EXIT depressed to leave the menu system. Writing and sending – Press MENU. – Scroll to Messages and press ENTER.
10 Infotainment system Menu structure –phone Overview 1. Call register 1.1. Missed calls 1.2. Received calls 1.3. Dialled no. 1.4. Erase list 1.4.1. All calls 1.4.2. Missed calls 1.4.3. Received calls 1.4.4. Dialled no. 1.5. Call duration 1.5.1. Last call 1.5.2. Call count 1.5.3. Total time 1.5.4. Reset timers 2. Messages 2.1. Read 2.2. Write 2.3. Message sett 2.3.1. SMSC number 2.3.2. Validity time 2.3.3. Message type 3. Phone book 3.1. New number 3.2. Search 3.3. Copy all 3.3.1. SIM to phone 3.3.2.
10 Infotainment system Menu structure –phone 10 5.5.3. Mute radio 5.5.4. Msg. beep 5.6. Traff. safety 5.6.1. Menu lock 5.6.2. IDIS 5.7. Factory sett. Description of menu options 1. Call register 1.1. Missed calls List of missed calls. You can choose to call, erase or store the number in the phone book. 1.2. Received calls List of received calls. You can choose to call, erase or store the number in the phone book. 1.3. Dialled no. List of previously dialled numbers.
10 Infotainment system Menu structure –phone 3.3. Copy all 4.3. Auto answer Copy phone numbers and names from the SIM card to the phone memory. Automatically answers incoming calls. 3.3.1. 3.3.2. Calls a previously engaged number. From SIM to phone memory From phone to SIM memory 3.4. One-key dial A number stored in the phone book can be stored as a speed dial number. 3.5. Erase SIM Erase the entire SIM card memory. 3.6. Erase phone Erase the entire phone memory. 3.7.
10 Infotainment system Menu structure –phone 5.5.2. 10 5.5.3. 5.5.4. Ring signal. There are seven different ring tones. Mute radio: On/Off Msg. beep 5.6. Traffic safety 5.6.1. 5.6.2. Menu lock. Deactivating the menu lock allows access to the entire menu while driving. IDIS. If the IDIS function is deactivated, incoming calls are not delayed, regardless of the driving situation. 5.7. Factory sett. Reset the system’s factory settings.
10 Infotainment system 10 225
Type designation .................................................................................... 228 Dimensions and weights ........................................................................ 229 Engine specifications ............................................................................. 230 Engine oil................................................................................................ 231 Fluids and lubricants......................................................................
SPECIFICATIONS 11
11 Specifications Type designation 11 Knowing the car’s type designation, vehicle identification and engine numbers can facilitate all contact with a Volvo dealer regarding the car and when ordering spare parts and accessories. 1. Type designation, vehicle identification number, maximum permissible weights, codes for colour and upholstery and type approval number. 2. Decal for parking heater. 3. Engine type designation, component and serial number. 4. Decal for engine oil. 5.
11 Specifications Dimensions and weights Dimensions Maximum load: See registration document. Length: 458 cm Max. roof load: 75 kg Width: 184 cm Trailer with brakes: Wheelbase: 264 cm Maximum trailer weight (kg) Front track: 155 cm Rear track: 156 cm 1500 Weights Kerb weight includes the driver, the fuel tank 90% full and all fluids. The weight of passengers and accessories,such as a towbar, load carriers, space box etc.
11 Specifications Engine specifications 11 2.4 2.4i T5 2.4D D5 Engine designation B5244S5 B5244S4 B5254T3 D5244T91 D5244T8 Output (kW/rpm) 103/5000 125/6000 162/5000 120/5500 136/4000 (hp/rpm) 140/5000 170/6000 220/5000 163/5500 185/4000 Torque (Nm/rpm) 220/4000 230/4400 320/1500–4800 340/1750-2750 400/222-2700 No. of cylinders 5 5 5 5 5 Bore (mm) 83 83 83 81 81 93.2 Stroke (mm) 90 90 93.2 93.2 2.44 2.44 2.52 2,40 2,40 10.3:1 10.3:1 9.0:1 17.0:1 17.
11 Specifications Engine oil Adverse driving conditions Viscosity chart Check the oil level more frequently for long journeys: • • • • towing a caravan or trailer. in mountainous regions. at high speeds. in temperatures colder than –30 °C or hotter than +40 °C. This can produce abnormally high oil temperature or oil consumption. Also check the oil level more often if the car is often driven short distances (less than 10 km) when temperatures are low (below +5 °C).
11 Specifications Engine oil Oil decal When the oil decal shown alongside here is in the car’s engine compartment, the following applies. See location on page 228. Oil grade: ACEA A3/B3/B4 Viscosity: SAE 0W–30 11 When driving under adverse conditions, use ACEA A5/B5 SAE 0W-30. Engine variant 2.4 B5244S5 2.4i B5244S4 T5 B5254T3 1Including 232 filter change. Volume between MIN –MAX (litres) Volume1 (litres) 0 —1.3 5.
11 Specifications Engine oil Oil decal When the oil decal shown alongside here is in the car’s engine compartment, the following applies. See location on page 228. Oil grade: WSS-M2C913-B Viscosity: SAE 5W–30 When driving under adverse conditions, use ACEA A5/B5 SAE 0W-30. Engine variant D5 D5244T8 2.4D D5244T9 1Including Volume between MIN – MAX (litres) Volume1 (litres) 1.5 6.
11 Specifications Fluids and lubricants Fluid Engine variant/number of components Gearbox oil 2.4 Manual 5-speed 2.1 2.4i Manual 5-speed 2.1 11 Coolant Transmission fluid: MTF 97309-10 2.0 T5 Automatic gearbox 7.75 Transmission fluid: JWS 3309 D5 Automatic gearbox 7.75 Transmission fluid: JWS 3309 5-cyl. Petrol, manual gearbox 9.5 5-cyl. Petrol, automatic gearbox 10.0 Coolant with corrosion inhibitor mixed with water, see packaging. The thermostat starts opening at 90 ºC 5-cyl.
11 Specifications Fuel Consumption, emissions and volume Engine 2.4 Gearbox B5244S5 2.4i B5244S4 T5 B5254T3 Consumption litre/100 km Emissions of CO2 (g/km) Tank volume (litres) 62 Manual 5-speed (M56) 8.9 212 Automatic gearbox (AW55-50/51) 9.6 229 Manual 5-speed (M56) 9.0 215 Automatic gearbox (AW55-50/51) 9.6 229 Manual 6-speed (M66) 9.1 217 Automatic gearbox (AW55-50/51) 9.8 234 D5 D5244T8 Automatic gearbox (AW55-51) 7.3 193 2.4D D5244T9 Automatic gearbox (AW55-51) 7.
11 Specifications Fuel Fuel consumption and emissions of carbon dioxide 11 Official fuel consumption figures are based on a standard driving cycle in accordance with EU Directive 80/1268 comb. Fuel consumption figures may change if the car is equipped with extra equipment that affects the car’s weight. The manner in which the car is driven and other non-technical factors can affect fuel consumption. Consumption is higher and power output lower for fuel with an octane rating of 91 RON.
11 Specifications Catalytic converter General Lambda-sondTM oxygen sensor The purpose of the catalytic converter is to purify exhaust gases. It is located in the flow of exhaust gases close to the engine so that it quickly reaches operating temperature. The catalytic converter consists of a monolith (ceramic or metal) with channels. The channel walls are lined with a thin layer of platinum, rhodium and palladium. These metals act as catalysts, i.e.
11 Specifications Electrical system General 12 volt system with a voltage-regulated alternator. Single pole system in which the chassis and engine block are used as conductors. 11 Voltage 12 V Cold start capacity (CCA) 590 A Reserve capacity (RC) 700 A2 100 min 120 min 135 min 60 70 80 equipped with diesel, audio system Premium Sound, fuel-driven heater or RTI.
11 Specifications Electrical system Bulbs Lighting Output W Socket Dipped beam 55 H7 Bi-Xenon 35 D2S Main beam 55 HB3 Brake lights, reversing lamps, rear fog lamp 21 BA15s Direction indicators, rear/front (yellow) 21 BAU 15s Rear position/parking lamps, rear side marker lamps 5 BAY15d Courtesy lighting, cargo area lighting, number plate lighting 5 SV8.5 Vanity mirror 1.2 SV5.5 5 W 2.1 x 9.5d Direction indicators in door mirrors (yellow) 5 W 2.1 x 9.
11 Specifications Electrical system Type approval, remote control system Country 11 A, B, CY, CZ, D, DK, E, EST, F, FIN, GB, GR, H, I, IRL, L, LT, LV, M, NL, P, PL, S, SK, SLO 1 IS, LI, N, CH HR ROK Delphi 2003-07-15, Germany R-LPD1-03-0151 BR RC ETC093LPD0155 1 Delphi hereby certifies that this remote control system conforms to the essential characteristic requirements and other relevant regulations of directive 1999/5/EC.
11 Specifications 11 241
Alphabetical index A A/C electronic climate control .......................70 ABS ...........................................................123 ABS fault ................................................43 Active Yaw Control ...................................125 active lamps .......................................... 61 setting .................................................... 63 Audio steering wheel keypad .......................... 55 Audio volume B Backrest front seat, lowering ...................
Alphabetical index C Call functions during an ongoing call ..........219 phone volume ......................................218 Call waiting ................................................217 Calls making and receiving ...........................217 Car care Child seat Collision fixture system ........................................ 32 installation ............................................. 32 Children collision sensors .................................... 23 crash mode ...........................
Alphabetical index Disc text ....................................................212 Economical driving ................................... 112 Display Electrical socket messages .........................................45, 46 Display lighting ............................................49 cargo area ............................................. 91 centre console ....................................... 47 rear seat ................................................ 57 Electronic immobiliser ............
Alphabetical index Fuel gauge ..................................................41 Fuse table fuses in the engine compartment ........196 fuses in the passenger compartment ..199 Fuses changing ..............................................194 general .................................................194 relay/fuse box in the engine compartment ........................................195 relay/fuse box in the passenger compartment ........................................198 G Off/On ......................
Alphabetical index homesafe light duration ...................50, 61 instrument lighting .................................49 lighting panel ..........................................48 main/dipped beam .................................50 position/parking lamps ..........................48 rear fog lamp ..........................................49 rear seat .................................................84 Lighting, bulb replacement Locking .....................................................
Alphabetical index Parking lamps .............................................48 Power windows .......................................... 58 REG – Regional radio programmes .......... 210 Passenger compartment filter .....................66 Programme functions ............................... 208 Relay/fuse box Personal preferences ..................................62 PTY –Programme type ............................. 209 approach light duration ..........................63 auto blower adjust .......
Alphabetical index Spin control .............................................. 125 Seats SRS system lowering the front backrest ....................77 manual setting ........................................76 Service locking ............................................99 general ................................................... 17 switch .................................................... 20 Stability control system ............................ 125 Storing stations, manual and automatic ...
Alphabetical index TP –traffic information ...............................208 Traction control .........................................125 U Waxing ...................................................... 169 Unlocking Traction control system ............................125 boot lid ................................................ 102 from inside ........................................... 103 from outside ........................................ 102 keyless ............................................
Volvo.
