Information

SAFETY INSTRUCTIONS
VERSION 01/19
VOLTCRAFT DSA-115 SPECTRUM ANALYZER
ITEM NO.: 1698260
VOLTCRAFT DSA-136 SPECTRUM ANALYZER
ITEM NO.: 1698261
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/
downloads or scan the QR code. Follow the instructions on the website.
Read the operating instructions before using the product.
INTENDED USE
• Frequency span range from 9 kHz to 1.5 GHz / 3.6 GHz
• Resolution 1 Hz
• Frequency span range: 0 Hz, 100 Hz up to the maximum frequency of the device
• Displayed average noise level -150 dBm
• Phase noise -82 dBc / Hz @1 GHz and offset at 10 kHz
• Overall amplitude accuracy <1.5 dB
• 10 Hz minimum resolution bandwidth (RBW)
• EMI pre-compliance test kit
• Ageing rate: <1 ppm/year
• Frequency counter resolution: 1 Hz, 10 Hz, 100 Hz, 1 kHz
• 1.5 GHz tracking generator kit:
• Output frequency range: 100 kHz ~ 1.5 GHz
- Output power range: -30 dBm ~ 0 dBm
- Front RF input connector: 50 Ω, type N female
• Front, panel tracking generator output connector: 50 Ω, type N female
• Communication port: USB host, USB device, LAN, headphone jack, VGA, REF
• 26.4 cm (10.4") colour TFT screen, 800 x 600 pixels
• Integrated help system can be called up on the display
The settings are made using the soft keys on the display interface.
The device complies with the provisions of EN 61010-1, protection class 2, overvoltage
protection CAT II (1000 V)
The measuring instrument is operated with a voltage between 100 – 240 V/AC at 50 – 60 Hz.
Do not make measurements in potentially explosive areas (Ex) or wet rooms or under unfa-
vourable ambient conditions. Unfavourable ambient conditions are: Moisture or high humidity,
dust and ammable gases, fumes or solvents, as well as thunderstorms or thunderstorm
conditions like strong electrostatic elds etc.
For safety reasons, when measuring only use measuring cables or accessories which are
adjusted to the specications of the meter.
The instrument should only be operated by persons who are familiar with the required regula-
tions and potential dangers. The use of personal protective equipment is recommended.
Use other than that described above can lead to damage to the product and may involve
additional risks such as, for example, short circuits, re, electrical shocks, etc. No part of the
product may be modied or recongured!
Read the operating instructions carefully and keep them for later reference.
The safety instructions are to be observed without fail!
EXPLANATION OF THE SYMBOLS
An exclamation mark within a triangle indicates important information
contained within this technical product documentation which must be
observed.
A lightning symbol inside a triangle warns against the danger of an electric
shock or impairment of the electrical safety of the device.
The arrow symbol is used when specic tips and advice on operation are
provided
Protection class 2 (double or reinforced insulation/ protective insulation)
CAT I
Measurement Category I (Overvoltage category) for measuring circuits of
electrical and electronic equipment that is not directly supplied with mains
voltage (e.g., battery-operated devices, protective extra-low voltage, signal
and control voltages, etc.).
CAT II
Measurement Category II (Overvoltage category) for measuring electrical
and electronic devices that are directly supplied with mains voltage via a
mains plug. This category also covers all smaller categories (e.g., CAT I for
measuring signal and control voltages).
CAT III
Measurement Category III (Overvoltage category) for measuring in building
installation (e.g., outlets or sub-distribution). This category also covers
all smaller categories (e.g., CAT II for measuring electronic devices). The
measuring operation in CAT III is permitted only with probe tips with a
maximum free contact length of 4 mm or with cover caps over the probe tips.
CAT IV
Measurement Category IV (Overvoltage category) for measuring at the
origin of the low-voltage installation (e.g., main distribution, electricity
provider's transfer points to homes, etc.) and outdoors (e.g., tasks on earth
line, overhead line, etc.). This category also contains all lower categories.
The measuring operation in CAT IV is permitted only with probe tips with a
maximum free contact length of 4 mm or with cover caps over the probe tips.
Earth potential