Instructions

ManualsBrandsVOLTCRAFT ManualsBattery ChargersVOLTCRAFT SPAS-8004 VC-8331410 USB charger Mains socket Max. output current 8 A 5 x USB, USB-C socket

• Neverpourliquidsoverelectricaldevicesorplaceobjectslledwithliquidnexttotheproduct.

If liquid or an object does enter the interior of the device, power down the respective socket

(e.g. switch off the circuit breaker), and then remove the mains plug from the mains socket.

Discontinue use and take the product to a specialist repair centre.

• Never use the product immediately after it has been brought from a cold room into a warm

one. The condensate generated can possibly destroy the product. Furthermore, this could

cause a lethal electric shock! Allow the product to reach room temperature before connecting

it and putting it to use. This may take several hours.

• Make sure the USB ports are not short-circuited.

• Ensure there is sufcient air circulation when you operate the product. Never cover the

product.

• Always switch off the USB device to be connected before connecting and disconnecting.

• Consult a technician if you are not sure how to use or connect the product, or if you have

concerns about safety.

• Maintenance,modicationsandrepairsmustbecarriedoutbyatechnicianoraspecialist

repair centre.

• If you have questions which remain unanswered by these operating instructions, contact our

technical support service or other technical personnel.

Product overview

1 USB-A output (4 x)

2 USB-C

output

3 LED operation lamp

4 Stand

5 Power cord socket

Setup

• Place the USB charger in the stand (4). Connect the connector of the supplied power cord to the power

cord socket (5). Connect the power plug to an appropriate power outlet. The LED operation lamp (3)

lights up.

• Connect a powered-off USB device to a USB-A port (1) or the USB-C

port (2). You can charge up to

vedevicesatthesametime.Pleasenotetheavailablechargingcurrents,seesection"Technicaldata".

A total of 8 A are available.

• The USB device will start to charge. Should you wish to operate the USB device, you may turn it on now.

Turn off the USB device before removing the product from the mains socket.

• Disconnect all connected USB devices from the USB charger after use. Disconnect the USB charger from

the mains socket after use. The LED operation lamp goes out after a few seconds.

Care and cleaning

• Disconnect the USB charger from the mains socket and connected devices before cleaning.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the

casing or cause the product to malfunction.

• Do not immerse the product in water or other liquids.

• Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable waste and must not be placed in household waste. At the end

of its service life, dispose of the product according to the relevant statutory regulations.

Youthusfullyourstatutoryobligationsandcontributetoprotectionoftheenvironment.

Technical data

Input voltage / current ........................... 100 – 240 V/AC, 50/60 Hz, 800 mA

Output voltage/current .......................... 5 V/DC, max. 8 A total, max. 3 A per USB output

Output power ........................................ max. 40 W

USB outputs ......................................... 4 x USB-A, 1 x USB-C

Operating conditions ............................. 0 to +40 ºC, 20 – 85 % RH

Storage conditions ................................ -20 to +60 ºC, 10 – 90 % RH

Dimensions (L x W x H) ........................60 x 30 x 72 mm (without stand)

Weight ..................................................approx. 220 g (with stand and cable)

Operating instructions

USB charger SPAS-8004

Item No. 1666282

Intended use

The product has four USB-A outputs and one USB-C

output. The product is suitable for charging and

operatingup toveUSB devicesat thesametime.Poweris suppliedviaastandardhousehold mains

socket. The product is protected against short circuit and overload.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g. in bathrooms)

must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. Using the product for

purposes other than those described above may damage the product. In addition, improper use can cause

hazardssuchasashortcircuit,reorelectricshock.Readtheinstructionscarefullyandstoretheminasafe

place. Only make this product available to third parties together with its operating instructions.

This product complies with statutory, national and European regulations. All company and product names are

Package contents

• USB charger

• Power cable (about 1 m in length)

• Stand

• Operating instructions

Up-to-date Operating Instructions

Download the up-to-date operating instructions at www.conrad.com/downloads or scan the QR code shown.

Follow the instructions on the website.

Explanation of symbols

The symbol with the lightning in a triangle indicates that there is a risk to your health, e.g. due to

an electric shock.

The symbol with an exclamation mark in a triangle is used to highlight important information in

these operating instructions. Always read this information carefully.

Safety instructions

Read the operating instructions carefully and observe safety instructions. If you do not

follow the safety information and information on proper handling in these operating

instructions, we will assume no liability for any resulting personal injury or damage to

property. Such cases will invalidate the warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing

material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,

moisture,ammablegases,vapoursandsolvents.

• Never expose the product to mechanical stress.

• If it is no longer possible to operate the product safely, stop using it and prevent unauthorised

use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stress.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height may

damage the product.

• Always observe the safety information and operating instructions of any other devices which

are connected to the product.

• Unplug the connected USB device from the product when you are not using it.

• If the product shows signs of damage, do not touch it, there is a risk of death from an electric

shock! First, switch off the mains voltage to the socket to which the product is connected

(switch off at the corresponding circuit breaker or remove the safety fuse or switch off at the

corresponding RCD protective switch, so that the socket is fully disconnected). You can then

unplug the power adapter from the mains socket. Dispose of the damaged product in an

environmentally friendly manner, stop using it. Replace it with an identical product.

• The mains outlet must be located near to the device and be easily accessible.

• The product must only be powered by a standard mains socket connected to the public grid.

Before plugging in the product, check that the voltage indicated on the product corresponds to

the voltage of your electricity supplier.

• Electrical devices must never be plugged in or unplugged with wet hands.

• Never disconnect electrical equipment from the power outlet by the cable, always pull it out of

the mains socket by gripping surfaces provided for this purpose.

• When setting up the product, make sure that the cables are not pinched, kinked or damaged

by sharp edges.

• Always lay the cables so that nobody can trip over or become entangled in them. This poses

a risk of injury.

• For safety reasons, disconnect the product from the mains socket during storms.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

Allrightsincludingtranslationreserved. Reproduction by anymethod (e.g.photocopying, microlming orcapturing in

electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is

prohibited. This publication represents the technical status at the time of printing.