Manual

6
Message Cause Solution
+ Beeping +"9"
The clamps are connected in
reverse.
Check the orientation of the clamps
and connect them to the correct
terminals. See section: Connection
[}5]
+ Beeping +"8"
The jump starter temperature
is too low or too high.
Restore the jump starter temperat-
ure to: -20 to +60 °C
+ Beeping +"7"
Over-current protection Avoid starting the vehicle for 30
seconds to prevent damage to the
jump starter.
+ Beeping +"6"
The vehicle has been started
more than 4 times in 10
minutes.
Avoid starting the vehicle for 10
minutes to disable protection
mode.
+ Beeping +"5"
The clamps have short cir-
cuited.
Ensure the clamps are not touch-
ing or connected to the same piece
of metal.
+ Beeping +"4"
The voltage of the car battery
is higher than 12.6V.
No jump starting is needed. Dis-
connect the jump starter from the
vehicle.
+ Beeping +"3"
The voltage of the jump starter
is too low.
Recharge the jump starter as soon
as possible to prevent battery dam-
age. See section: Charge the
product [}5]
11 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.
12 Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
■
in our Conrad offices
■
at the Conrad collection points
■
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
13 Technical data
13.1 General
Input (USB-C®) .............................. 5 V/DC 3 A, 9 V/DC 3 A, 12 V/DC 3 A, 15 V/DC 3 A,
20 V/DC 2.25 A
Rechargeable battery ..................... 4x 14.8 V 5000 mAh 74 Wh, Li-ion (non-removable)
Recharge time ................................ 10 hrs (normal adaptor)
2 hrs (PD 45 W adaptor)
LED light modes ............................. Constant ON → SOS → flashing → OFF
Brightness: max. 280 lm
Operating conditions....................... -20 to +60 °C, 40 – 85 % RH (non-condensing)
Storage conditions.......................... 0 to +45 °C, 40 – 85 % RH (non-condensing)
Dimensions (L x W x H).................. 243 x 113 x 66 mm
Weight ............................................ 1500 g
13.2 Protection mechanisms
Over temperature ........................... discharging: 60 °C ±5 °C
recharging: 60 °C ±5 °C
Low temperature............................. discharging: -20 °C ±5 °C
recharging: -20 °C ±5 °C
Overvoltage (USB-C®)................... max. 6 V
Overcharge..................................... 16.6 V
Over discharge ............................... software: 12.5 V - 13 V
hardware: 10.8 V - 11 V
Overcurrent..................................... USB-A: max. 3.7 A
USB-C® (5 - 15 V): max. 3.5 A
USB-C® (20 V): max. 2.7 A
DC output: max. 15 A
13.3 Power bank
Output (USB-C®) ........................... 5 V/DC 3 A, 9 V/DC 3 A, 12 V/DC 3 A, 15 V/DC 3 A,
20 V/DC 2.25 A (max. 45 W)
Output 2 (USB-A) ........................... 5 V/DC 3 A, 9 V/DC 2 A, 12 V/DC 1.5 A (max. 18 W)
Output 2 (USB-A) ........................... 5 V/DC 3 A, 9 V/DC 2 A, 12 V/DC 1.5 A (max. 18 W)
Output (DC) .................................... 15 V/DC 10 A (max. 150 W)
13.4 Jump starter
Vehicle on-board system................ 12 V/DC
Start current (peak value)............... 1000 A (2000 A)
Jump starts..................................... approx. 15 (affected by factors such as ambient
temperature, size, and mechanical condition of the
engine)
Suitable engine types ..................... Petrol (displacement max. 10 L), Diesel (displacement
max. 8 L)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2878223_V1_0723_dh_mh_en 9007200166950283-2 I2/O1 en