Manual

5
6 Product Overview
6.1 Product
1
2
3
4
5
6
7
8
9
1 LCD screen 2
BOOST button
3
ON/OFF button
4 DC output jack
5 Starter cables socket 6 Ports cover
7 USB-C®: input/output 8 USB-A: output
9 USB-A: output
6.2 Display
A
B
C
D E F
H
I
G
A Product battery %:
charge / discharge / standby
B IN:
Input connected
C OUT: Output connected D USB-A connected
E USB-C® connected F DC jack connected
G BOOST:
Ready to jump start the vehicle
H Charging / discharging power
I Warning, see section:
Warning messages [}5]
6.3 Starter cables
A
B
C
A Starter cables plug B Black starter clamp (-)
C Red starter clamp (+)
7 Charge the product
Tip:
Use a 45W fast charger to maximize recharging performance.
Preconditions:
a
You have a suitable power adaptor.
1. Connect one end of the included USB-C® cable to a power adaptor.
2. Connect the other end of the cable to the USB-C® input on the product.
3. Press the button to start charging.
à The battery capacity will show on the display.
à The display will switch OFF when charging is complete.
8 Connection
8.1 Preparation for connection
Before connecting the cables to a battery:
■
Switch OFF all vehicle electrics (e.g. air conditioner, heater, radio, lights etc.).
■
Make sure the ignition key is in the "OFF" position. For push-to-start ignition, make sure
the vehicle is completely OFF.
■
Check the battery contact terminals are clean.
■
Prepare your vehicle for ignition (e.g. place gear in park and engage the emergency
brake).
8.2 Connecting the leads
Important:
Always connect test leads to terminals in the correct order.
1. Connect the red clamp to the positive (+) terminal.
2. Connect the black clamp to the negative (-) terminal.
3. Wiggle the clamps back and forth to ensure proper connection.
8.3 Disconnecting the leads
When finished using the product:
1. Disconnect the red clamp.
2. Disconnect the black clamp.
9 Operation
Important:
Fully charge the product before using it for the first time. See section: Charge the product
[}5]
9.1 Jump start the vehicle
Preconditions:
a
The product is at least 50% charged. See section: Charge the product [}5].
a
The vehicle is prepared for connection. See section: Preparation for connection [}5].
1. Connect the starter cables. See section: Connecting the leads [}5].
2. Press the button to switch the product ON.
3. Press and hold the BOOST button until BOOST appears on the display.
4. Start the vehicle engine.
à An alarm will sound if any protection mechanisms activate. See section: Warning
messages [}5]
5. If the engine starts, disconnect the starter cables. See section: Disconnecting the leads
[}5].
6. If the engine does not start, switch the ignition OFF and repeat steps 3 & 4.
Important:
Let the vehicle run for approximately 30 mins. to recharge the battery.
9.2 Power bank
Preconditions:
a
To use this product as a power bank you will need a suitable charging cable.
1. Connect one end of the charging cable to your mobile device, and the other end to an
output on the product.
2. Press the button to start charging.
3. Disconnect the cable when charging is complete.
Note:
DC output port
– The DC output port is capable of delivering 15V 10A.
– Use it with the included auxiliary power outlet to DC male cable adaptor.
9.3 LED light
1. Press and hold the button to switch the LED ON/OFF.
2. Press the button repeatedly to cycle through modes: constant ON → SOS → flash-
ing → OFF.
10 Warning messages
If a protection mechanism activates, an alert will sound and a warning message will appear
on the display.