Owner's Manual
Table Of Contents
- 2 Einführung
- 3 Bestimmungsgemäße Verwendung
- 4 Lieferumfang
- 5 Aktuelle Bedienungsanleitungen
- 6 Symbolerklärung
- 7 Sicherheitshinweise
- 8 Bedienelemente und Komponenten
- 9 Produktbeschreibung
- 10 Displayanzeigen und Symbole
- 11 Messbetrieb
- 11.1 Messgerät einschalten
- 11.2 Spannungsmessung “V”
- 11.3 Strommessung „A“
- 11.4 Widerstandsmessung
- 11.5 Diodenprüfung
- 11.6 Durchgangsprüfung
- 11.7 Messung der Kapazität
- 11.8 Berührungslose Wechselspannungsdetektion „NCV“
- 11.9 Frequenzmessung
- 11.10 Pulsweitenmessung
- 11.11 Raumtemperatur- und Luftfeuchtemessung
- 11.12 Temperaturmessung mit Kontaktfühler
- 11.13 Schallpegelmessung
- 11.14 Beleuchtungsmessung
- 11.15 RANGE-Taste
- 11.16 Taste REL
- 11.17 Taste Hz%
- 11.18 HOLD-Taste
- 11.19 MODE-Taste
- 11.20 Abschaltautomatik
- 11.21 Displaybeleuchtung
- 12 Fehlersuche
- 13 Reinigung und Pflege
- 14 Entsorgung
- 15 Technische Daten
- 2 Introduction
- 3 Intended use
- 4 Delivery content
- 5 Up-to-date operating instructions
- 6 Description of symbols
- 7 Safety instructions
- 8 Operating elements
- 9 Product description
- 10 Display indications and symbols
- 11 Measuring
- 11.1 Switching on the measuring instrument
- 11.2 Voltage measurement “V”
- 11.3 Current measurement “A” 10
- 11.4 Resistance measurement
- 11.5 Diode test
- 11.6 Continuity test
- 11.7 Capacity measurement
- 11.8 Contact-free AC voltage detection “NCV”
- 11.9 Frequency measurement
- 11.10 Pulse width measurement
- 11.11 Room temperature and humidity measurement
- 11.12 Temperature measurement with contact sensor
- 11.13 Noise level measurement
- 11.14 Lighting measurement
- 11.15 RANGE button
- 11.16 REL button
- 11.17 Hz% button
- 11.18 HOLD button
- 11.19 MODE button
- 11.20 Auto power-off function
- 11.21 Display illumination
- 12 Troubleshooting
- 13 Cleaning and care
- 14 Disposal
- 15 Technical data
- 2 Introduction
- 3 Utilisation prévue
- 4 Contenu de l’emballage
- 5 Mode d’emploi actualisé
- 6 Description des symboles
- 7 Consignes de sécurité
- 8 Éléments de fonctionnement
- 9 Description du produit
- 10 Indications apparaissant à l’écran et symboles
- 11 Mesures
- 11.1 Mise en marche de l’appareil de mesure
- 11.2 Mesure de la tension « V »
- 11.3 Mesure du courant « A »
- 11.4 Mesure de la résistance
- 11.5 Test de diode
- 11.6 Contrôle de continuité
- 11.7 Mesure de la capacité
- 11.8 Détection sans contact de la tension alternative « NCV »
- 11.9 Mesure de fréquence
- 11.10 Mesure des largeurs d’impulsions
- 11.11 Mesure de la température ambiante et de l’humidité de l’air
- 11.12 Mesure de la température avec sonde à contact
- 11.13 Mesure du niveau sonore
- 11.14 Mesure de la luminosité
- 11.15 Touche RANGE
- 11.16 Touche REL
- 11.17 Touche Hz%
- 11.18 Bouton HOLD
- 11.19 Bouton MODE
- 11.20 Fonction de désactivation (OFF) automatique
- 11.21 Eclairage de l’écran
- 12 Dysfonctionnements
- 13 Nettoyage et entretien
- 14 Élimination des déchetsd
- 15 Caractéristiques techniques
- 2 Inleiding
- 3 Beoogd gebruik
- 4 Leveringsomvang
- 5 Meest recente gebruiksaanwijzing
- 6 Beschrijving van de symbolen
- 7 Veiligheidsinstructies
- 8 Bedieningselementen
- 9 Productbeschrijving
- 10 Indicaties en symbolen op de display
- 11 Meten
- 11.1 Meetapparaat inschakelen
- 11.2 Spanningsmeting “V”
- 11.3 Stroommeting “A”
- 11.4 Weerstandsmeting
- 11.5 Diodetest
- 11.6 Doorgangstest
- 11.7 Capaciteitsmeting
- 11.8 Contactloze wisselspanningsdetectie “NCV”
- 11.9 Frequentiemeting
- 11.10 Pulsbreedtemeting
- 11.11 Kamertemperatuur- en luchtvochtigheidmeting
- 11.12 Temperatuurmeting met contactsensor
- 11.13 Geluidsniveaumeting
- 11.14 Belichtingsmeting
- 11.15 RANGE-toets
- 11.16 REL-toets
- 11.17 Hz/%-toets
- 11.18 HOLD-toets
- 11.19 MODE-toets
- 11.20 Automatische uitschakelfunctie
- 11.21 Displayverlichting
- 12 Probleemoplossing
- 13 Onderhoud en reiniging
- 14 Verwijdering
- 15 Technische gegevens
Fuse F1 F2
Value FF 500 mA 660V F10A H 600V
Dimensions 5 x 20 mm 6�3 x 32 mm
– Now close the housing again carefully�
Using mended fuses or bridging the fuse holder is not permitted for safety reasons. It may cause res or
arc explosions� Never operate the meter when it is open�
13.5 Inserting and changing the batteries
Operation of the measuring device requires a 9V battery (e�g� 1604A)� You need to insert a new, charged battery prior
to initial operation or when the battery change symbol appears on the display�
Proceed as follows to insert or change the batteries:
– Separate the connected measuring lines from the measuring circuit and the measuring device� Switch off the
DMM�
– Open the housing as described in chapter “Opening the meter”�
– Replace the at batteries with new one of the same type. Place a new battery into the battery compartment
(18), observing the correct polarity� Observe the correct polarity indicated in the battery compartment�
– Now close the housing again carefully�
Never operate the measurement device when it is open� !RISK OF FATAL INJURY!
Do not leave at batteries in the device. Even batteries protected against leaking can corrode and thus
release chemicals which may be detrimental to your health or destroy the battery compartment�
Do not leave batteries lying around carelessly� They could be swallowed by children or pets� If swallowed,
consult a doctor immediately�
Remove the batteries if the device is not used for longer periods of time to prevent leaking�
Leaking or damaged batteries may cause alkali burns if they come in contact with the skin� Therefore, use
suitable protective gloves�
Make sure that the batteries are not short-circuited. Do not throw batteries into the re.
Batteries must not be recharged or dismantled� Danger of explosion!
Note:
– You can order suitable alkaline batteries stating the following order no�:
Item no� 65 25 09 (please order one piece)�
– Only use alkaline batteries, as they are powerful and have a long service life�
53