User manual

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2017 by Conrad Electronic SE. 1562815ff_V2_0917_02_VTP_m_en
Package contents
Digital oscilloscope
4 probes
USB cable
Power cable
BNC –BNC cable (only for oscilloscopes with frequency generator function)
Software CD
Quick guide
Operating controls
1 Power switch
2 USB host-connector - is used to store data on a USB stick or to update Firmware
3 CAL. -Calibration output 1 KHz/2 Vp-p square wave signal.
4 GND. Earth connection, reference potential
5 GEN OUT - frequency generator output for oscilloscopes with frequency generator
function
6 CH 1 – 4 - BNC measurement input Channel 1 - 4
7 EXT. - BNC-Trigger external input
8 Vertical - Vertical control range
9 Trigger - Trigger control range
10 Horizontal - Horizontal control range
11 Menu - Selection of menu item shown
12 F Adjust buttons - Selection of menu item shown
13 Display - Display zone
Getting started
Check all the parts for completeness and damage after unpacking.
Damaged parts must not be used for safety reasons. In case of any damage
contact our customer service.
Installation of the measurement program
Switch on your computer and insert the enclosed software CD into the CD drive of your com-
puter. The automatic start mode will automatically start the installation of the measurement pro-
gram. If the program does not start automatically, open the le „setup.exe“ in the CD directory
Making measurements
The measuring signal should only be applied to the internal conductor. The
external conductor (reference earth) is connected to the earth potential (pro-
tective earth conductor)
Che
ck the measuring device and its measuring leads for any damage before each measurement.
Never take any measurements if the protecting insulation is defective (torn, missing, etc.).
To avoid electric shock, do not touch the connections/measuring points directly or indirectly
during measurements.
Never reach beyond the grip surface of the probes during a measurement process. There is
danger of a life-threatening electric shock.
Do not use the device shortly before or after a thunderstorm (lightning! / high-power surges!).
Make sure that your hands, shoes, clothing, the oor, the measuring device and/or measuring
lines, circuits and circuit components are always dry.
Measurements in circuits >30 V/AC and >30 V/DC may be carried out only by specialists and
trained persons who are familiar with the pertinent regulations and the resulting dangers.
Follow the necessary safety instructions, regulations and protective measures for the intrinsic
safety
Cleaning
Before cleaning the device, switch it off and disconnect it from power, the USB cable and the
device under test.
Live components may be exposed if the covers are opened or parts removed
(unless this can be done without tools).
Prior to cleaning or repairing the device, all lines must be detached and the
device must be turned off.
Do not use scouring, chemical or aggressive cleaning agents such as benzene, alcohol or
similar chemicals. These might attack the surface of the device. Furthermore, the fumes are
explosive and hazardous to your health. Moreover, you should not use sharp-edged tools,
screwdrivers or metal brushes, or the like for cleaning
For cleaning the device and the measuring leads, use a clean, slightly damp, fuzz-free, an-
tistatic cloth.
Disposal
Electronic devices are recyclable material and do not belong in the household waste.
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical data
Measurement inputs ..................... Four separated channels CH1 - CH4
Bandwidth ..................................... 80 MHz / 100 MHz / 200 MHz / 250 MHz
Rise time ....................................... ≤ 4.4ns / < 3.5 ns / ≤ 1.8ns / < 1.4ns
Input impedance ........................... 1 MOhm ± 2% // 20 pF ±3pF
Max. input voltage ........................ CH1 – CH4: max. 300V RMS (probe setting 10×)
External trigger ............................. 0 – 3,3 V
Input coupling ............................... DC-AC-GND
Probe ratio .................................... 1:1/10:1
Vertical resolution ......................... 8 bit
Vertical deection ......................... 500 µV - 10 V/div
Vertical accuracy .......................... ± 3% 10 mV/div – 10 V/div / ± 4% 500 µ V/div – 5 mV/div
Time base ..................................... 2 ns to 100 s/div
Time based accuracy ................... ± 50 ppm
Sampling rate ............................... 1GS/s
Memory depth ............................... 64 Kpts
Trigger mode ................................ auto, norm
Arbitrary function generator
Output frequency .......................... Sinus 0.1Hz - 25 MHz
...................................................... Rectangle 0.1 Hz - 10 MHz
...................................................... Ramp 0.1 HZ - 1 MHz
...................................................... EXP 0.1 Hz - 5 MHz (rise/fall)
Scanning frequency ...................... 200 MS/s
Vertical signal resolution ............... 12 bits
Output voltage range .................... 5 mVss to 3.5 Vss (50 Ω);
...................................................... 10 mVss to 7 Vss (high impedance)
Software ...................................... Windows
®
VISTA/7/8/10
Interface ........................................ USB2.0
Power ........................................... 100 – 120 V AC / 45 – 440 Hz
...................................................... 120 – 240 V AC / 45 – 60 Hz
Working conditions ....................... 0 °C to +50 °C, ≤ 90%, non-condensing
Storage conditions ........................ -40 °C to +70 °C, ≤ 60%, non-condensing
Height ........................................... max. 3000 m
Weight .......................................... approx. 2900 g (without accessories)
Dimensions (L x W x H) ................ approx. 318 x 110 x 150 mm