4 / 8CH H.264 STANDALONE DVR VEDVR 2304B / VEDVR2308B USER MANUAL 2011 April. V1.
WARNING Do not expose the DVR under the sunlight, heat or wet environment while installation. As it could decrease the performance of DVR and damage the machine. Do not touch the power plug or case with wet hands as this could result electric shock. Do not forcedly bend or put heavy object on power cable as this could result in injury to personal or equipment. Do not operate with damaged power cord or loose electrical outlet as this could result in electric shock or accident.
iii
CONTENTS 1. 2. 3. Specification ............................................................................................. 1 Front Panel ............................................................................................... 2 Installation ................................................................................................ 3 4. 5. 6. 7. DVR Installation ........................................................................................ 3 System Operation ......................
1.
2. Front Panel MENU Stop Manual Record Pause Step Forward Play Fast Rewind Rewind speed: x2 / x4 / x8 / x16 / x32 Fast Forward Forward speed: x2 / x4 / x8 / x16 / x32 Slow Forward Slow Forward speed: 1/2, 1/4, 1/8 Up Down To move up or down of the selection setting in the menu. Left Right To move left or right of the selection setting in the menu. Enter Press the Enter button to confirm the setup or go into sub-menu. USB 2.
3. Installation 1 USB Mouse Port 2.0 USB Mouse 2 Video In 3 Video Out 1CH Video Output (BNC) 4 Audio Out 1CH Audio Output (RCA) 5 Audio In 6 Alarm 7 DC12V 8 XGA PC Monitor Output 9 LAN RJ-45 Network Connection 10 RS-485 8CH Video Input (BNC) 4CH Audio Input Alarm I/O Power Input For Speed Dome Use Item Point 1: CH1 sensor input. Point 2: CH2 sensor input. Point 3: CH3 sensor input. Point 4: CH4 sensor input. Point 5: ground. Point 6: the first relay joint port.
Alarm Installation Please refer to Installation for external alarm I/O installation. Please refer to Alarm Setup. Speed Dome Installation This device can support 3 kinds of communication protocol (Pelco D, Pelco P & MIKAMI) Power Installation Please use the provided power cable and adaptor to connect the DVR (AC100V~AC230V). Please refer to Installation for connecting position. The DVR system will enter into live viewing mode when power is connected.
Virtual Keyboard Operation The text input of the virtual keyboard is as below: Menu Operation Select character from virtual keyboard Keyin the select character Exit the virtual keyboard Front Panel & Remote Control Operation [Up/Down/Left/Right] [Enter] [MENU] Mouse Operation [Move Cursor] [Left Click] [Left Click]out of selection area Key Description of Virtual Keyboard Delete the previous character Switch to text input Enter key.
Setup Operation Front Panel & Remote Control USB Mouse Select [Up/Down/Left/Right] [Moving Cursor] Confirm Select Setting [Enter] [Left Click] Change the Select Setting [Left/Right] [Left Click] Return to Upper Menu [MENU] Right Click 6. Display Setup There are 3 kinds of screen display mode: Live, Auto Switching and PTZ. DVR. Live Viewing Mode The DVR will go to the live viewing mode after boot up.
Quick Menu Setup Operation Front Panel & Remote Control USB Mouse Select Item [Left/Right] [Moving Cursor] Enter the Select Item [Up/Down] [Moving Cursor] Confirm the Select Item [Enter] [Left Click] Exit [MENU] [Left Click] out of selection area PTZ Please set the speed dome properly before control PTZ. Please refer to PTZ Setup.
Playback Operation Setup Operation Front Panel & Remote Control USB Mouse Fast Rewind [Fast Rewind] Fast Forward [Fast Forward] Step Forward [StepForward] | Step/Pause [Step/Pause] | Play 1x [Play] Stop [Stop] Digital Zoon Drag by Left Click 1~8Single Channel Display [1~8 Channel] 8split Display [8split] Select Channel [Double left click] Under single channel [Double left click] Auto Switching 1. Auto switch starts from order CH1~CH8, 8 split channel. 2.
Setup Operation Front Panel & Remote Controller USB Mouse Search [Enter] [Left Click] Select Channel [Up/Down] [Moving Cursor] Select Dates [Up/Down/Left/Right] [Moving Cursor] Playback [Enter] [Left Click] Return to Upper Menu [MENU] [Right Click No data: no color, data of alarm trigger: red color, normal record data: green color. Select the first half of hour frame under the date, the playback will start from 00 mins: 00 sec.
Enter Select Item Front & Remote Controller [Enter] Select Item [Up/Down/Left/Right] [Moving Cursor] Return to Upper Menu [MENU] [Left Click] Setup Operation USB Mouse [Left Click] First Page Previous Page Next Page Last Page Mark all the events in this page BackUp List all of recording data and click on one of record data to playback. Backup Please click “BACKUP” to backup the selecting file to USB memory stick. 8.
8.1 Camera Setup Channel Select one channel to set. Use CopyButton to copy present settings to other channels. Camera Title Set the title of camera. Key in by using virtual keyboard. Title Position Set the title position. Set: Top Left, Top Right, Bottom Left, Bottom Right and Off.
Type Speed dome model type. Set: PTC-301, PTC-203ST, FUM 626, JG_QG988, FUM 622SD, FUM 628 or off. Please select the correct communication protocol if you enable this setting. Protocol Speed dome protocol. Set: PELCO P, PELCO D, MIKAMI or off. Address Speed dome address. Set: 0~255 Baud Rate Speed dome baud rate. Set: 1200, 2400, 4800, 9600, 19200. Tour Time Speed dome tour time. Set: 5, 10, 15, 20, 25 sec or off. Tilt Opposite Set speed dome image upside down.
Buzzer Duration The buzzer ON duration when video loss. Alarm Relay Duration The Relay ON duration when video loss. Time Display Display the time in LIVE mode. Values: ON/OFF. 8.2 Record Setup Channel Switch On/Off the channel. Resolution NTSC Recording Resolution : 720x480, 720x240, 360x240. PAL Recording Resolution: 720x576, 720x288, 360x288. Frame Rate Setting of Frame Rate: NTSC: 0-30 frames/sec; PAL: 0-25 frames/sec. Quality Setting of recording quality: Values 1-5.
Setup Operation Front Panel & Remote Controller USB Mouse Enter Select Item [Enter] [Left Click] Select Channel [Up/Down] [Moving mouse wheel] Select Time&Date [Up/Down/Left/Right] [Click/Drag-draw] Return to Upper Menu [MENU] [Right Click] Copy (1) Select source (2) Select target (3) Press COPY icon to copy. 8.3 Alarm Setup Channel Select the channel to set. COPY icon can copy the present setting to other channels. Mode Enable/disable alarm trigger. Set: On/Off.
Motion Detection Select the channel to set. COPY icon can copy the present setting to other channels. Channel Status Enable/disable motion detection for each camera. Set: On/Off Sensitivity Sensitivity level of motion detection. Set: 1~10. Higher value equal more sensitive. Motion Area Setup Setup by each small square.
Mode Set the connection method. Set: Static IP, DHCP, PPPoE. Media port Port used for stream media. Default is port 9000. Webport Port used for web access. Default is port 80. Command Port Port used for settings. Default is port 8000. IP Address Assigned IP address. Net mask Assigned net mask Gateway Assigned gateway PPPOE Need account and password for PPPoE. DDNS setting DNS1 First Domain Name Server，Default : 168.95.1.1 DNS2 Second Domain Name Server, Default :168.95.192.
E-MAIL Forward E-mail after alarm triggered. Enable: On/Off SSL Enable the SSL encryption. Recommend to set on if it is using gmail. SMTP port SMTP port number key in. For example, gmail port 465. SMTP Server SMTP server key in. For example, gmail : smtp.gmail.com From Sender E-mail address key in. For example, gmail: mail1@gmail.com Password Sender E-mail account password To Receiver E-mail address key in. For example, gmail: mail2@gmail.
Setup Operation Front & Remote Controller USB Mouse Enter Select Item [Enter] [Left Click] Select Item [Up/Down/Left/Right] [Moving Cursor] Return to Upper Menu [MENU] [Right Click] First Page Previous Page Next Page Last Page Backup to USB disk ★ When Trigger Recording is marked , Click to playback. 8.7 Backup Channel Backup all channels or single channel 1-8. Record Type Select all, normal or alarm. Start/End time Select the backup range of time. Press Search to start searching.
8.8 System 8.8.1 Time Setting Date/Time Select by using virtual keyboard. Date Format Setup Set: YY/MM/DD, MM/DD/YY. Time Format Setup Set: 24Hours, 12Hours. Time Zone Setup Time Zone setting of DVR.
8.8.2 HDD Setup Format Format the selected HDD Format HDD Overwrite Enable/Disable Overwrite, Values: On/Off. If Overwrite is enabled, the period can be set as 6, 12, 24, 36, 48 hours and 7, 15, 30, 60 days. Pack Time Set the required packing time frame to allow the system to pack each saving file under continue recording mode. Pack time setting: 5 min, 10min, 15min, 20min, 30min, and 60min. Buzzer for HDD When the hard drive does not have enough space or something wrong, set the buzzer on.
Format USB Memory Stick 8.8.3 Display Setting GUI Display GUI display mode can be VIDEO or VGA. Video Switching Time Set the switching time when switching channels in video mode. Values: 1-99 seconds. (0 sec is Off) VGA Switching Time Set the switching time when switching channels in VGA mode. Values: 1-99 seconds. (0 sec is Off) Switching Sequence Set the switching sequence of channels. Video Margin Set the display margins of the screen.
XGA Resolution XGA Resolution: 800x600, 1024x768, 1280x1024, 1440x900. 8.8.4 System Information Provide the firmware version, MAC address, HDD status…. 8.8.5 User password Password Setup Enable/Disable password checking. Values: On/Off (Default) Administrator account/password can not be blank. And at least 4 characters for the password. Administrator account/password Administrator account allows user to access all of functions. User account/password Access rights can be assigned by setting.
8.8.6 System Language Language Values: Traditional Chinese, Simplified Chinese and English. Auto rebooting after change. Function Tip Show function tips below the menu items. Value: On/Off (Default). 8.8.7 Audio setting 8.8.8 Audio Volume Set the volume of audio In/Out. Values: 1-10. (Default: 5) System Maintenance Auto maintenance: Set time for auto rebooting. Value: On/Off.
F/W update Please plug the USB memory stick into the USB port on the DVR rear panel after download the new firmware to the USB memory stick. Note: the firmware only can be upgraded by using the USB port. Please don’t operate the system, remove the USB memory stick or remove the power while it is in upgrade progressing in order to prevent any serious system error. The system will automatic reboot after upgrade. Load Setup Default Load factory default. Refer to [Default Setting].
6. Enter the correct IP address and click on “Open” 7. Click on “Connect” to connect to the DVR. 8. Connecting 9. Connected Menu 10. If fail to connect, please repeat steps 7 to 9.
1. 2. Android mobile surveillance: The mobile phone must support Android 2.1 (Test mobile: Motorola XT701). Open Internet Explorer on the mobile phone. 3. Enter the IP Address of DVR. 4. Connected. Channel: Channel selection. Display Delay: Display Delay selection. SIZE: Display size selection. 3G MOBILE SUPPORT LIST Brand Model Number System HTC HD mini T5555 Windows Mobile 6.5 HTC P3700 Windows Mobile 6.1 HTC Desire HD A9191 Android 2.
10. H264Player Operation Preface H264Player software allows to playback the backup saving file from the DVR. System Requirement Operating System: Windows 2000, XP, Vista, Windows 7. Program obtainment and installation While user start to backup the file from DVR, the system will automatically copy the H264Player.exe file and recorded data to the backup device for example, an USB flash memory stick.
Step4: Install Confirmation Step 5: Installation Complete User Interface Open File Click Pause Click Stop Click Play 1x Click Fast Forward Click Slow Forward Click Capture the image (snap shot) to the host computer Volume Control Click Drag 28
Rewind Click Step Forward Click Right click the mouse to open the Pop-up Menu pop-up menu including Setting, Language, About H264Player, Exit 11. Web Operation Preface The Web Application Manager allows the user to remotely monitoring, playback, backup through the DVR. System Requirement Operating System: Windows 2000, XP, Vista, Windows 7 Web Browser: Internet Explorer Add-on Installation Please use the IE browser to login the IP address of DVR setting.
Please login user name and password from the setting of DVR end.
Playback (1) Select Date Event Search (2)Click or (3)Click Playback Click on pop up file list Fast Forward Click “Fast Forward” (Speed: 2X, Rewind Click “ Rewind” (Speed: 1/2, 1/ 4X, 1/ 8X, 1/ 16X) Step Forward Click “Previous”or “Step” Snapshot Click 4X, 8X, 16X) to capture.
Record Please refer “Record Setup” for more information. Alarm Please refer “Alarm Setup” for more information.
Please refer “Motion Detection” for more information.
System Setting Date/Time Setting HDD Management Display 34
System Information Account/password Audio Setting 35
System Maintenance Host setting 36
12.
13. USB Flash Memory Stick Support List The following recommended flash drives have passed all testing procedures and are safe to a: backup, b: Playback by PC, and c: update firmware.
