AG-188 User Manual AG-188N User Manual 1 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 1 AG-188N Features ...............................................................................................4 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 3 4 Web Configuration ...............................................................................................7 2.1 2.2 2.3 Access Web setting page..........................................................................................7 Current state..........................................................................
AG-188 User Manual 6 7 8 9 Network Diagnosis .............................................................................................34 Restore to factory default..................................................................................34 POST Mode(safe mode) ...................................................................................35 FAQ.......................................................................................................................
AG-188 User Manual 1 AG-188N Features 1.1 PWR： SYS : WAN: LAN: PSTN: VoIP: call out 1.2 Power: Port: WAN: LAN: Appearance power connection status server registration status . registered: on , gliting , not-registered , off WAN port connectiong , contected , on , offline : off LAN port connectiong , contected , on , offline : off light on when PSTN call come in/out light on when VoIP call come in/out , The default status when pick up the call is VoIP Interface Output Power:12VDC,500mA. RJ11 port.
AG-188 User Manual 1.3 z z z 1.4 Electricity characteristic Speciality of electric: output the 12V 500mA DC The network connects:2 RJ45 connect, a WAN, a LAN FXS: 2 port Software z z z z z z z z z z z z z z z z z z z z z Support two sip servers running at the same time. Back-up sip server support. NAT, Firewall. DHCP client and server. Support PPPoE, (used for ADSL, cable modem connecting). Support major G7.xxx CODEC. VAD,CNG. G.
AG-188 User Manual z z z z z z 1.6 Telnet: Internet's remote login protocol DNS: Domain Name Server TFTP: Trivial File Transfer Protocol HTTP: Hyper Text Transfer protocol FTP: File Transfer protocol RFC 3362：T.38 protocol Compliant Standards z z z z CE：EN55024,EN55022 FCC part15 comply with ROHS in EU comply with ROHS in China z Explanation: The letter “e” is the first letter of “environment: and “electronic”, The rim is a round with two arrow , stands for recycle.
AG-188 User Manual 1.9 Installation Use Ethernet cable to connect AG-188N’s LAN port and your computer. Set your computer’s ip to the network 192.168.10.x or using dynamic obtain IP. Open your web browser and key in 192.168.10.1. Then you will see the logon page of AG-188N, the default username and password is admin/admin for administrator and guest/guest for guest. Set up page for VoIP use only: Internet PBX Power PSTN User POS Phone 2 Web Configuration 2.
AG-188 User Manual 8 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.2 Current state This page shows AG-188N’s running state. Network ：shows the WAN and LAN port connecting state and current settings. VoIP： show the default protocol, the working state of SIP and IAX2, you can see whether AG-188N has registered the public sip server and IAX2 server. Phone Number shows the public sip server、 the private sip server and the IAX2 server phone numbers. 9 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.3 Network 2.3.1 Wan Config WAN port network setting page. Support static IP, dynamic obtain IP and PPPoE.
AG-188 User Manual 2.3.2 LAN Config Bridge Mode: Enable this option to switch to bridge mode. Gateway won’t assign IP for its LAN port in bridge mode and its LAN and WAN port will be in the same network. (This setting won’t take effect unless you save the config and reboot the device) IP Netmask: Set the IP and Netmask for the LAN DHCP Server: Enable DHCP service in LAN port NAT: Enable NAT. 2.4 VoIP 2.4.
AG-188 User Manual Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the same IP for register server and proxy server, in this case you don’t need to configure the proxy server information. ) Proxy Server Port: Signal port of SIP proxy Proxy Username: proxy server username Proxy Password: proxy server password SIP domain, enter the sip domain if any, otherwise AG-188N Domain Realm: will use the proxy server address as sip domain.
AG-188 User Manual 2.4.2 Iax2 Config Setting page of public IAX IAX Server Addr: IAX Server Port: Account Name: server: Register address of public IAX server Register port of public IAX server，default port is 4569 Username of your SIP account (Always the same as the phone number) Account Password: Password of your IAX account.
AG-188 User Manual 2.5 Advance 2.5.1 DHCP Server DHCP server manage page. User may trace and modify DHCP server information in this page. Update Mode: Using DHCP updated model ,None expressed are not updated, Update firmware update firmware is used to DHCP. Update file is used to configure DHCP updated configuration files. Tftp Server: Addresses using TFTP server upgrade 。 DNS Relay: enable DNS relay function. User may use below setting to add a new lease table. Lease Table Name: Lease table name.
AG-188 User Manual 2.5.2 NAT Advance NAT setting. Maximum 10 items for TCP and UDP port mapping. IPSec ALG: Enable/Disable IPSec ALG; FTP ALG: Enable/Disable FTP ALG; PPTP ALG: Enable/Disable PPTP ALG; Transfer Type: Transfer type using port mapping. Inside IP: LAN device IP for port mapping. Inside Port: LAN device port for port mapping. WAN port for port mapping. Outside Port: Click Add to add new port mapping item and Delete to delete current port mapping item. 15 / 42 VoIPon www.voipon.co.
AG-188 User Manual 2.5.3 Net Service HTTP Port: configure HTTP transfer port, default is 80.User may change this port to enhance system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to reconnect. Telnet Port: configure telnet transfer port, default is 23. RTP Initial Port: RTP initial port. RTP Port Quantity: Maximum RTP port quantity, default is 200 Notice: Settings in this page won’t take effect unless save and reboot the device.
AG-188 User Manual 2.5.4 QoS settings AG188 implement QoS based on 802.1p, The QoS is used to mark the network communication priority in the data link/MAC sub-layer. AG188 will sorted the packets using the QoS and sends it to the destination. 1. Voice 802.1p Priority --- Configure the priority of the voice packets in 802.1p protocol. 2. VLAN Enable --- Disable/Enable VLAN function 3. Voice VLAN ID 4. DiffServ Enable --- Disable/Enable Diffserv service 5.
AG-188 User Manual 2.5.5 Advance SIP settings This page is used to set the private sip server, stun server, and back up sip server information. STUN Server setting: STUN Server Addr: configure stun server address; STUN Server Port: configure stun server port default 3478 STUN Effect Time: stun detect NAT type circle, unit: minute. Enable SIP STUN: enable/disable stun. Please refer to sip conf for the setting for how to set the public alter server.
AG-188 User Manual 2.5.6 Digital Map Digit map is a set of rules to determine when the user has finished dialing. AG-188N support below digital map: Digital Map is based on some rules to judge when user end their dialing and send the number to the server. AG-188N support following digital map: ----End With “#”: Use # as the end of dialing. ----Fixed Length: When the length of the dialing match, the call will be sent. ----Timeout: Specify the timeout of the last dial digit.
AG-188 User Manual 2.5.7 Call Service Settings User configure the value add service such as hotline, call forward, call transfer, 3-way conference call .etc in this page Hotline: configure hotline number. AG-188N immediately dials this number after hook-off if it is set. Call Forward: Please refer to value add service for detail. No Disturb: DND, do not disturb, enable this option to refuse any calls. Ban Outgoing: Enable this to ban outgoing calls.
AG-188 User Manual 2.5.8 MMI Filter MMI filter is used to make access limit to AG-188N Gateway. When MMI filter is enable. Only IP address within the start IP and end IP can access AG-188N gateway. 21 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.5.9 Audio Settings CODEC: select the prefer CODEC; support ulaw, alaw and G729 Signal Standard: Support CHINA, Japan and USA standard Input Volume: Handset in volume. Handset out volume. Output Volume: G729 Payload Length: G729 payload length VAD: Enable/disable Voice Activity Detection FAX Mode: select the FAX Mode 2.5.10 VPN this page is VPN setting page , the Gateway support the VPN with UDP and L2TP protocol .
AG-188 User Manual VPN Server Addr： register to the address of VPN server 。 VPN Server Port： Register to the port of VPN server Server Group ID： the group ID of UDP VPN Server Area Code： the are code of VPN server L2TP VPN Server Addr： register to the address of VPN server VPN User Name： L2TP VPN username VPN Password： L2TP VPN password UDPTunnel: use the UDP to visit VPN L2TP: use the L2TP to visit VPN Enable VPN: Enable the VPN server, you must choose UDP or L2TP type in advance 23 / 42 VoIPon www.
AG-188 User Manual 2.6 Dial-Peer Settings Please refer to “how to use dial rule?” for detail. 24 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.7 Config Manage Save Config: Clear Config: save current settings. restore to default settings. Notice: clear config in admin mode, all settings restores to factory default; clear config in guest modem, all settings except sip, advance sip restore to factory default. 25 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.8 Update 2.8.1 Web Update: update gateway’s settings or firmware. Firmware file is .dlf extension when configure file is .cfg extension, AG-188N will auto select configure update or firmware update according the extension. 2.8.2 FTP Update: back up the configure file to FTP or TFTP server. Or auto update configure file from your auto update server. Back up configure file to your FTP/TFTP server. * configure use .cfg extension. 2.8.
AG-188 User Manual Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file Config Encrypt Key: The encrypt key of confirmation file Protocol Type: The protocol type that used for upgrading Update Interval Time: The interval time that the terminals search for new configuration file.
AG-188 User Manual 2.9 System Manage 2.9.1 Account Manage Set web access account or keypad password of AT-530. 2.9.2 Syslog Config: Server IP: set the syslog server address Server Port: set the syslog server port MGR Log Level: set the MGR log level SIP Log Level: set the SIP log level IAX2 Log Level: set the IAX2 log level Please click “apply” after setting 28 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 2.9.3 Time Set: Server:type the ip address of time server Timezone:select correct time zone in list box Timeout: longest response time for SNTP Manual Timeset:The time setting Daylight: Daylight Saving time 2.9.4 Logout&Reboot Reboot Gateway, some setting needs to reboot to make it works. Please always save config before reboot, otherwise the setting will return to previous setting. 29 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 3 IVR setting User may pre-config AG-188N gateway using a normal phone connecting to AG-188N. please refer the below command: Notice: all command below can be end with # to speed response.
AG-188 User Manual 4 Telnet Console 4.1 Introduce 4.1.1 Basic structure User may use telnet command to access and manage gateway. AG-188N adopts tree structure for telnet. Every node contains its sub-nodes or local command. User can type “help” or “?” whenever to see sub-nodes and all local command under current node. Besides local command, there are some global commands can be used in each node. 4.1.2 Basic command Logout: exit telnet mode. Write: save current settings.
AG-188 User Manual 4.2 Global Command Global command is available under all nodes, AG-188N support following commands: Command Function Example exit Return to parent-node #exit logout Exit #logout ping Ping command, use to check network, #ping www.google.com write Save setting to flash #write 32 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 5 Tree Structure 5.1.1 Debug (Level 0~7) path: # show debug setting [disable]enable debug all modules [disable]enable debug app module [disable]enable debug cdr module [disable]enable debug sip module [disable]enable debug tel module [disable]enable debug dsp module ---show ---[no] all xxx ---[no] app xxx ---[no] cdr xxx ---[no] sip xxx ---[no] tel xxx ---[no] dsp xxx 5.1.2 reload usage: #reload Reboot system 5.1.
AG-188 User Manual ¾ uptime path: # show running time Example:## uptime ¾ version path: # show gateway version Example:## version 5.1.4 telnet and logout Usage: #telnet –target -port Login:xxx Password:xxx # #logout 5.1.5 tracert trace network path info usage: #tracert –host Example:#tracert www.google.com 6 Network Diagnosis There are some telnet commands for checking your network.
AG-188 User Manual 8 POST Mode(safe mode) AG-188N provide safe mode. When there is booting problem because of setting problem or firmware problem. User can restore the factory setting or upgrade to a new firmware to solve this problem. How to enter safe mode? In the AG-188N booting procedure, it use the static ip 192.168.1.179 (WAN port IP) for a short time, user can telnet to this ip address in this occasion to enter the save mode.(remember to change your PC into the network 192.168.1.
AG-188 User Manual 9 FAQ How many SIP servers may AG-188N register simultaneously? AG-188N support 2 SIP servers and a IAX server. The Default server is SIP . If you want to use the IAX server you must set IAX as default protocol in the IAX config page. IAX and SIP can register simultaneously but not work simultaneously. If you set 2 SIP servers in the SIP setting page , you can choose the route (server) by dialing plan which is edited by you. Please see “How to use the dial rule?” for detail.
AG-188 User Manual Destination (optional): call destination, can be IP or domain. Default is 0.0.0.0, in this case the call will be routed to the Public SIP server. If you set the destination to 255.255.255.255, then the call will be routed to the private SIP server. Also you can key other address here to make direct IP calls Port (optional): Configure the port of the destination, default is 5060 Alias (optional):Set up the Alias. We support four Alias as below.
AG-188 User Manual How to use speed dial function? Please refer to “How to use dial rule?”. How to configure digital map? Please refer digit map settings. How to use Call Forward, Call Transfer and 3-way Conference calls? User may set up the configuration in the Call Service page to use these value add service. ¾ Call Forward: ----Forward when busy: select Busy in the Call Forward Field, and Key in the destination phone number in the Forward Number.
AG-188 User Manual number. ¾ Call Transfer: Check the Enable Call Transfer. If A is the AG-188N user, and B calls and talking with A through VoIP. A can press the Hook-Flash to hold the call with B, and then press * and then enter C’s number. B will be transferred to C and can talk with C. ¾ 3-Way Conference Calls Check Enable Three Way Call Only sip protocol support this function .Assume A is the AG-188N user, and B calls and talking with A through VoIP.
AG-188 User Manual 2. if “Data/Voice VLAN differentiated” is Tag differentiated but the DiffServ is disable. Device won’t distinguish the voice, signaling and data stream. It will add the same data vlan id to them. As below: Or 40 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 3. if “Data/Voice VLAN differentiated” is Tag differentiated and diffServ are both enable. Then device will distinguish the voice, signaling and data stream to VLAN ID setting. As below: Or 41 / 42 VoIPon www.voipon.co.uk sales@voipon.co.
AG-188 User Manual 4.if “Data/Voice VLAN differentiated” is Date untaged and diffServ are both enable. Then device will undistinguish the date to VLAN ID setting. As below: 5. if VLAN is disable. Device won’t add any vlan ID to the stream. In this case, if the Diffserv is enable, the DiffServ value response to the voice/signaling stream. 6. When VLAN function is enable. If “VLAN ID check” is enable, AG188 will have strict requirement on the VLAN, it won’t handle any packets with different VLAN ID.
