Specifications

STARPLUS@ 616 FLEX
KEY TELEPHONE SYSTEM
CePTION 200 3L\r
FEATURE
200.1
ACCOUNT CODES
An account code is the last field within Station Mes-
sage Detail Recording (SMDR), that provides the
ability to track specific calls by entering a non-veri-
fied, variable length (up to 8digits) identifier. Account
codes can be entered by the user during a call and
can be used with SMDR information for billback
purposes.
200.2 ALARM SIGNALING
The system can recognize either an open or closed
loop from an external relay and transmit an alarm
signal. This signal can be sent to all programmed
stations with either a single or repeated tone. The
type of alarm tone is selected in system program-
ming.
This feature can be used as an entry door alarm. In
addition, the Alarm Reset code can be programmed
onto a Flex button which will flash during alarm
signaling.
200.3
ALL CALL PAGING
Stations allowed to make pages may make voice
paging announcements ‘to all idle stations, phone
boxes and external paging ports at the same time.
200.4
ATTENDANT POSITION
Any key telephone station may be assigned as the
system attendant. The assigned attendant will re-
ceive unattended line recalls and will initiate NIGHT
SERVICE.
200.5
ATTENDANT OVERFLOW
System programming allows the attendant station to
be programmed so that if the attendant is busy or not
there, the call will be automatically forwarded to
another predetermined station after a programmed
period of time.(Refer to Call Forward-Preset)
200.6
ATTENDANT RECALL
A CO line placed on hold or transferred will initiate
the recall timer if the associated timer has been
enabled in programming. When the timer expires,
the CO line will ring the station that placed it on hold.
lf not answered, the timer continues and upon expi-
ration again, the attendant station will ring. If still not
answered and the timer cycles again, then all tele-
phones programmed with direct access of that CO
line will ring and flash the CO line LED at the recall
rate. If still unanswered and the recall timer expires
again, the CO line will be dropped.
DESCRIPTION
200.7 AUTOMATIC PRIVACY
Privacy is automatically provided on all calls. The
system may be programmed to eliminate privacy,
allowing another station to join in on existing CO
(outside) line conversations.
200.8 AUTOMATIC SELECTION
The user can select an outside line, intercom station
or speed dial button or dial a feature & automatically
place the phone in the dialing mode without pressing
the ON/OFF button or lifting the handset.
The system may be programmed optionally to re-
quire the user to lift the handset or press the ON/OFF
button before accessing outside CO Lines.
200.9
AUTOMATIC PAUSE INSERTION
If a flash is programmed into system and station
speed dial numbers, and last number redial num-
bers, a pause will automatically be inserted after the
flash. A pause will also be automatically inserted
after a PBX dialing code has been used & after a
pulse to tone switchover is programmed into speed
dial numbers.
200.10 BACKGROUND MUSIC
Key telephone & phone box users may receive mu-
sic over their speaker when an optional music source
has been connected to the system. The music can
be turned on or off and the volume adjusted at each
individual telephone or phone box. The maximum
loudness level can be adjusted on the KSU.
Phone boxes that are denied DND in data base
programming, can receive music through their
speaker or the Attendant can activate BGM at any
phone box by dialing a code.
This feature can be allowed or denied on a per
station basis by programming.
Background Music enable code can be programmed
onto a Flex button. When BGM is enabled, Flex
button LED will light.
200.1 I BASIC KEY TELEPHONE COMPATI-
BILITY
The Starplus Basic Electronic telephone will operate
on the 616 FLEX system. The Basic key set contains
six (6) Flexible buttons, eight (8) “fixed” feature but-
tons, a 12 key DTMF dial pad and an “HTP” switch.
The Basic set provides on-hook dialing and Call
Announce on intercom.
k%WF
1
.IANl
IAPV
iaai
^^^ .