User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
Visual Training Devices
Figure 37: Pidion BM-170 and QTERM-G55
• Visual training devices enable operators to read the words that they need to say during the enrollment
training process.
• Vocollect recommends using a browser-based mobile display with Talkman A500 or A700 devices, and
the QTERM-G55 with Talkman T5 or T2x devices.
• These devices have a liquid-crystal screen that displays words that an operator needs to train. Operators
are more likely to speak in their normal conversational tone when reading the words than when hearing
the device say the words during training.
• Vocollect provides a cable with a connector so that the QTERM device can be attached to the red port on
the device.
• Supporting documentation and software for the QTERM visual training device is available for free download
on the manufacturer’s website. Please refer to this site for all supplemental product information such as
the user manual, specifications, data sheet, tutorials, and accompanying software.
Note: In order to use QTERM devices with a Thai TTS, you must use a QTERM-G55 running device
software version 3.1 or newer. After connecting the QTERM, verify you have the correct software by
checking debug logs for the message "TRAIN DEVICE: Device query detected training device G55
using v3.1." If you do not see this message, you do not have the correct software, and you must obtain
it to use the device with a Thai TTS.
Setting Up the QTERM Visual Training Device
1.
Verify that the training device is set up properly. Refer to the instructions that QSI or your reseller provided
with the training device for more information.
2.
Connect the training device to the device using the cable provided.
3.
In the task name.vcf file, set the configurable parameter TrainDevicePort = Red to turn on the training
device port.
4.
Reload the task onto the device.
If the training device does not work after a task load, power the Talkman device off, then power it on again.
Configuring the QTERM Visual Training Device
Note: You cannot change the default baud rate for the QTERM training device setting of 9600 for versions
of VoiceClient 1.x or 3.x.
1.
Verify that the task is loaded onto the device.
2.
Verify that the device is sleeping.
3.
Verify that the training device is connected to the device.
Confidential: For informational use by Honeywell resellers and customers only
74 | Vocollect Talkman A500 Product Guide