User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
SolutionTextNumber
—Flash library failed while opening a
file.
0x210f
—Flash library failed while closing a
file.
0x2110
—Flash had invalid flash file image
generator linked list.
0x2111
—Flash is full. Please wait while
Talkman turns off.
0x2112
—Flash library failed. Out of space.0x2115
—Flash library failed during reclaim.0x2116
Spoken Error Messages
SolutionError Message
Change the battery."Battery is very low. Powering off. Must
replace battery after power off complete."
Change the battery."Battery is getting low."
Change the battery."Battery is getting low. Change battery
now."
Wait until all templates are loaded, then load the operator."Cannot load operator while sending
templates."
"Cannot load task. Processing data."
1.
Turn the device off and then turn it back on again.
2.
Reload the task.
3.
Reboot the device.
4.
Reload VoiceClient.
"Corrupt task file. Task load failed."
1.
Turn the device off and then turn it back on again.
2.
Reload the task.
3.
Reboot the device.
4.
Reload VoiceClient.
"Corrupt device emulation config file. Task
load failed."
Reload the operator."Corrupted operator data."
"Failed to load lookup table. Task load
failed."
1.
Go to an area of known good coverage.
2.
Turn the device off and then turn it back on again.
3.
Reload the task.
4.
Reboot the device.
5.
Reload VoiceClient.
"Failed to load task audio file. Task load
failed."
1.
Go to an area of known good coverage.
Confidential: For informational use by Honeywell resellers and customers only
Troubleshooting Equipment Problems | 53