User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
Installing the T5/A500 Charger Wall Mount
You will needParts
• Drill with 1/8” bit• 1 mounting bracket
• •4 self-drilling screw anchors #10 Screw driver, #2 Phillips
•• Drilling template sheet (included)4 washers, #10 flat, type B regular
• 4 screws, #10 Phillips pan head
1.
Using the drilling template, mark four holes for the anchors. Note that there are two sets of pilot markers;
one set for wall studs with 12 inch centers and one set for wall studs with 16 inch centers.
The bottom anchor holes must be at least 12 inches from the floor.
2.
Drill the pilot holes for the anchors, and screw the anchors into the holes.
3.
Position the mounting bracket so that its flat side is against the wall, aligned with the anchors, and the
mounting pins are away from the wall.
4.
Insert a screw through a washer and a hole in the bracket, then into the anchor. Tighten screw. Repeat
for remaining screws.
5.
Tilt the charger back and slide it onto the wall by lining up the tabs on the top of the bracket with the
notches in the back of the charger.
6.
Level the charger so the supports on the bottom of the bracket are underneath the charger.
Figure 26: Supports Underneath Charger
About LED Indicators
Vocollect Talkman devices, SRX and SRX2 headsets, and their chargers have LEDs that indicate the state
of the equipment. These LEDs may be on, off or blink. In some cases an LED will blink, alternating between
two colors.
If the LEDs indicate that there is a problem, refer to information on troubleshooting to solve the problem. See
also Troubleshooting Problems Indicated by LED.
A500/T5-Series Charger LED Indicators
The upper pair of indicators applies to the charger's battery slots. The lower pair applies to the device slots.
The LED conditions described here apply to the lower pair.
Note: If there is no device in the charger or if the device in the charger does not have a battery and one
of these conditions occurs,disconnect the charger from its power source for about five seconds, then
reconnect the charger. If the condition persists, return the charger for service.
Confidential: For informational use by Honeywell resellers and customers only
Chargers | 41