User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
• The T5/A500 charger may be fixed to a wall using the available wall mount kit.
Note: Do not place a device into a charger without a battery attached to it.
If a device that has been on and in use for more than eight hours will automatically power off and then
back on after it has been in the charger for five minutes. Also, a device that has been in a charger for
more than eight hours will automatically power off and then back on.
T5/A500 Single-Bay Combination Charger
• A T5/A500 Single-Bay Combination Charger is also available. It includes one battery slot and one device
slot. The charger can store one device at a time and store and charge up to two batteries at a time - one
battery in the upper slot and one battery in the device in the lower slot.
Connecting the Power Supply to the T5/A500 Combination Charger
1.
Connect the AC cord to the left end of the power supply that is mounted inside the charger.
2.
Route the cable through the plastic clips as shown.
Figure 25: Cable Routed Through Plastic Clips
3.
Push the clips to lock the cord in place.
T5/A500 Combination Charger Wall Mount
This unit provides a convenient surface for mounting the T5/A500 10-Bay Combination Charger and its power
supply on a wall.
• Customer assembly required.
• Be aware of potential hazards (electrical wires, waterlines, etc.) when drilling the pilot holes.
• Customer assumes all responsibility for the installation of these units.
• A device charger cannot have another charger placed directly above it. A section of dry-erase board
(included) must be placed above each device charger.
• If you drill into a wall stud when drilling a pilot hole for one of the anchors, do not use an anchor with that
hole.
• The lowest anchor for each extrusion must be a minimum of 12 inches from the floor.
• Avoid blocking power outlets and other wall receptacles when installing the extrusions and charger unit.
Confidential: For informational use by Honeywell resellers and customers only
40 | Vocollect Talkman A500 Product Guide