User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
Figure 17: Power Supply Attached to a Secure Surface on the Vehicle
9.
Run the cable that connects the battery adapter to the power supply from the power supply to the location
where the A500/T5 VMT will be mounted
10.
Connect the yellow wire to the battery adapter by attaching the connector and tightening the nut.
Connecting the A500/T5 VMT Device to a Vehicle's Power Source
You will need the following equipment:
• Two fuse holders from Cooper Bussman. Vocollect recommends using a Cooper Bussmann HFA series
in line waterproof fuse.
• Two fuses. Vocollect recommends a 2A 250V SLO BLO fuse.
• Three spade connectors
• Four small cable ties
• Fasteners
Vocollect recommends choosing unswitched power as the source for the power supply. This will allow Talkman
devices to be powered for software updates as well as prevent Talkman devices from accidentally being
unpowered if the vehicle is quickly switched off unintentionally.
1.
Remove all power sources from the vehicle.
2.
Remove any excess length from the cable from the input cable from the power supply.
3.
Connect the fuses to the cable near to the battery end of the cable. Remove approximately 4 inches of
the outer insulation from the cable.
4.
Expose approximately 10mm of copper on the positive and negative wires.
5.
Insert the exposed copper into the fuseholders and crimp into the positive and negative wires using an
approved tool.
6.
Connect the green wire to the vehicle's ground.
7.
Connect the fused white wire to the vehicle’s positive power source using an appropriate connector. This
may need to be crimped onto the wire.
8.
Connect the fused black wire to the vehicle’s negative power source using an appropriate connector. This
may need to be crimped onto the wire.
9.
Attach the power supply as shown in the following diagram.
Confidential: For informational use by Honeywell resellers and customers only
34 | Vocollect Talkman A500 Product Guide