User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
3.
On the cable from power supply to the vehicle’s power source, strip the three cables to expose approximately
5mm of copper. Ensure the cable is long enough to reach from the power supply to the vehicle’s power
source.
4.
On the yellow cable from the battery adapter to the power supply, strip the black and brown cable to expose
approximately 5mm of copper. The Blue cable is not required; it can be trimmed where it exits the yellow
cable. Ensure the cable is long enough to reach from the power supply to the vehicle’s power source.
5.
Connect the cables from the battery adapter to the power supply by performing the steps below.
• Loosen the screws to where the connection will be made on the power supply.
• Match the cables to the correct locations as indicated in the chart below:
•
Output ConnectorCable
+Brown – Battery Adapter Positive
-Black – Battery Adapter Negative
GNDNo connection needed
Not applicableBlue (cut back)
• Tighten the screws.
• Ensure the cables are secure
6.
Connect the cables from the vehicle’s power source to the power supply by performing the steps below:
• Loosen the screws to where the connection will be made on the power supply.
• Match the cables to the correct locations as indicated in the chart below:
•
Input ConnectorCable
+White (may differ depending on the cable) – Vehicle Positive
-Black (may differ depending on the cable) – Vehicle Negative
GNDGreen - Vehicle Ground:
Follow equipment manufacturer’s recommendations for connecting the case
ground terminal of the power supply.
• Tighten the screws.
• Ensure the cables are secure
7.
Once all of the cables have been successfully installed, attach cable ties to secure the cables.
Figure 16: Cables Attached to the Power Supply
8.
Place the power supply in a place out of the way, such as under the dashboard of a fork lift, and attach it
to a secure surface with cable ties. Alternatively the power supply could be secured by bolting it using the
mounting slots.
Confidential: For informational use by Honeywell resellers and customers only
Talkman A500 VMT | 33