User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
6.
Attach the cable from the power supply to the battery adapter.
To prevent vibration, the arm of the mounting bracket should not touch the stem of the ball of the base. In
other words, the arm should not be tilted so far as to have these pieces touching.
Connecting Cables to the Power Supply and Attaching the Power Supply to
a Vehicle
The following parts are supplied by Vocollect for attaching the 12 or 24 volt vehicle's power supply to a device:
DescriptionQuantityItem #
Power Supply, 9-36 VDC Input11
Cable from power supply to battery adapter12
The following parts are supplied by Vocollect for attaching the 36 or 48 volt vehicle's power supply to a device:
DescriptionQuantityItem #
Power Supply, 18-60 VDC Input11
Cable from power supply to battery adapter12
You will need the following equipment:
• One Cable from the power supply to vehicle’s power source. Vocollect recommends an industrial rated
cable with the following specifications: Number of conductors = 3, Gauge of wire = 16, Temperature =
-40C to 90C
• Cable ties
Caution: General Guidelines for Routing Electrical Cables
• The vehicle must be off and the vehicle's battery must be disconnected.
• Cables should be kept clear of surfaces that may become hot.
• Cables should not be run such that they can get caught on moving parts.
• Cables should not be run on the outside of a vehicle.
• Cables should not have 90 degree turns, the minimum bend radius should not be less than one inch
• To remove slack on a cable it should be coiled up and secured inside the vehicle with a cable tie.
• For maximum safety fuses should be located as close as possible to the power source.
• To protect the A500/T5 VMT from power surges and to perform voltage conversion a converter module
is fitted between the A500/T5 VMT and the forklift battery.
1.
Disconnect the vehicle battery.
2.
Remove the four screws from the top of the power supply to expose the screw terminals.
Confidential: For informational use by Honeywell resellers and customers only
32 | Vocollect Talkman A500 Product Guide