User's Manual
Table Of Contents
- Contents
- About Honeywell Documentation
- Introduction
- Using the Talkman A500
- Charging an A500 or T5 Device
- Charging an A500 or T5 Battery in a Device
- Charging an A500 or T5-Series Battery
- Removing an A500, T2-Series or T5-Series Device From a Charger
- Inserting a Battery into a Talkman A500, T5-Series or T2-Series Device
- Removing a Battery from a Talkman A500, T5-Series or T2-Series Device
- Battery Warm-Up Time
- Easy Configuration
- Turning a Talkman Device On
- Turning a Talkman Device Off
- About LED Indicators
- Loading an Operator's Templates
- Adjusting the Voice
- Understanding Talkman Commands
- Options for Hearing Impaired Users
- Cleaning Procedures for Honeywell Equipment
- Charging an A500 or T5 Device
- Talkman A500 VMT
- Mounts for Talkman A500/T5 VMT
- Talkman A500/T5 VMT Accessories
- Positioning the Talkman A500/T5 VMT
- Installing the Mounting Brackets for a Talkman A500/T5 VMT
- Connecting Cables to the Power Supply and Attaching the Power Supply to a Vehicle
- Connecting the A500/T5 VMT Device to a Vehicle's Power Source
- Removal of an A500/T5 VMT Device from Vehicle
- VMT Installation Best Practices
- Chargers
- Troubleshooting Equipment Problems
- I Can't Hear Anything Through the Headset
- The Scanner will not Scan
- The Device Beeps Every Few Seconds
- The Device Will Not Load a Voice Application
- The Device Will Not Load an Operator Template
- The Device Does Not Respond to Button Presses
- The Device Will Not Turn On
- The Device Keeps Shutting Off
- Troubleshooting Guide for the Talkman A500/T5 Battery Charger
- Troubleshooting Problems Indicated by LED
- About Error Messages
- Contacting Technical Support
- About Sending Equipment Back for Repairs
- Troubleshooting VMT Configurations
- Specifications
- Accessories
- Part Numbers
- Template Training Options
- Compliance
- Index
Chapter 3
Talkman A500 VMT
A Talkman A500 VMT is an A500 device with a battery adapter mounted to a vehicle, such as a forklift or
motorized pallet jack. After the device is mounted, the battery adapter is placed in the battery area of the
A500 device and connected to the vehicle’s power source.
Talkman devices in this configuration may use any wired or wireless equipment (headsets, scanners, etc.).
Vocollect sells the complete solution including mounting kits and power systems to enable any Talkman A500
devices to be used in an A500 VMT configuration.
Caution: PLEASE DO NOT LOOK AT DEVICE/UNIT WHILE OPERATING MACHINERY SO AS TO
AVOID CREATION OF A DISTRACTION THAT COULD RESULT IN AN ACCIDENT AND BODILY
INJURY TO OPERATOR AND THIRD PERSONS.
Follow the instructions below to properly install the device in a forklift.
• Determine the best location for mounting the device, taking into consideration the driver’s field of view.
• Install the appropriate mounting hardware.
• Connect the device to the vehicle’s wiring system.
Mounts for Talkman A500/T5 VMT
The Screw On Mount is a mounting option that is bolted to a stationary surface on a vehicle.
The Clamp Mount is a mounting option that is clamped to a stationary surface on a vehicle. This can also be
bolted to a stationary surface, if desired.
The Claw Mount is also clamped to a stationary surface, but can be clamped to oddly-shaped or horizontal
or vertical surfaces.
Figure 9: Claw Mount
Figure 8: Clamp MountFigure 7: Screw On Mount
Confidential: For informational use by Honeywell resellers and customers only