Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix K: Client: Vocollect, Inc. Model #: HBT1000-01 Standards: FCC 15.247 & RSS-210 ID’s:MQO-HBT1000-01/2570A-HBT100001 Report #: 2012186 Manual Please refer to the following pages; the compliance information appears in Appendix A.
Vocollect Hardware Documentation August 2012 ETP.HW.4100.2012.
Notice About Vocollect Documentation © 1987-2012 Vocollect. All rights reserved. Vocollect 703 Rodi Road Pittsburgh, PA 15235-4558 Phone: 412-829-8145 Fax: 412-829-0972 http://www.vocollect.com Trademark Vocollect product and company names, as well as their respective logos are trademarks or registered trademarks of Vocollect. All other product names mentioned herein are trademarks or registered trademarks of their respective owners.
Contents | 5 Contents Chapter 1: Introduction.................................................................................17 General Safety Guidelines...........................................................................................................................17 Vocollect Battery Safety....................................................................................................................18 Cleaning Procedures for Vocollect Equipment.............................................
6 | Vocollect Hardware Documentation Battery Warm-Up Time.....................................................................................................................41 About LED Indicators...................................................................................................................................42 A500 Device LED Indicators.............................................................................................................
Contents | 7 Pairing an A500 or T5-Series With the Honeywell MS9535: Talkman Device Is the Acceptor.........................................................................................................................68 Pairing an A500 or T5-Series Device with Zebra QL Series Printers............................................68 Pairing an A500 or T5-Series Device with Intermec PB50 Printers..............................................
8 | Vocollect Hardware Documentation Charging a T1 Battery with a T1 Single Charger Cable.................................................................95 Removing a T1 Device From a T1 10-Bay Combination Charger...................................................95 Disconnecting a T1 Device from a T1 Single Charger Cable...........................................................95 Inserting a Battery into a Talkman T1 Device................................................................................
Contents | 9 SRX Wireless Headset Specifications.............................................................................................116 Charging the SRX Headset.............................................................................................................117 Installing the SRX Mobility Strap..................................................................................................119 Wearing an SRX Wireless Headset...............................................................
10 | Vocollect Hardware Documentation T1 10-Bay Combination Charger Specifications............................................................................164 T1 10-Bay Combination Charger Power Supply Specifications....................................................164 T1 10-Bay Combination Charger Wall Mount...............................................................................164 T1 Single Charger Cable..........................................................................................
Contents | 11 Vocollect Connector Pin Specifications......................................................................................................197 Vocollect Bar Code Device Adapter...........................................................................................................198 Vocollect Bar Code Serial Interface Cable................................................................................................198 Vocollect T2 Series Bluetooth Adapters Specifications...............
12 | Vocollect Hardware Documentation Chapter 12: Listening Kits...........................................................................225 Wired Listening Kits..................................................................................................................................225 Monitoring Audio on a Talkman Device.........................................................................................226 Monitor Audio on a Handheld Device...................................................
Contents | 13 Vocollect® T5 and T5m Devices and Talkman T5 VMT Mobile Computers Declaration of Conformity..............................................................................................................................262 ® Vocollect T2x Devices Declaration of Conformity...................................................................................263 Vocollect® T1 Devices Declaration of Conformity.....................................................................................
14 | Vocollect Hardware Documentation Declaration of Conformity dos Computadores Corporais T5 e T5m e Computadores Móveis Talkman T5 VMT Vocollect®......................................................................................298 Vyhlásenie o zhode prenosných terminálov Vocollect ® T5 a T5m a mobilných terminálov Talkman T5 VMT........................................................................................................
Contents | 15 Vocollect® SRX Wireless Headset Dikjarazzjoni ta' Konformità..................................................345 Conformiteitsverklaring voor Vocollect® SRX draadloze hoofdtelefoon.......................................346 Vocollect® Samsvarserklæring for SRX trådløse hodetelefoner...................................................347 Deklaracja zgodności bezprzewodowych zestawów słuchawkowych Vocollect® SRX..................
16 | Vocollect Hardware Documentation Confidential: For informational use by Vocollect Resellers and customers only
Chapter 1 Introduction The Vocollect Hardware Documentation contains comprehensive information about hardware products and peripherals.
18 | Vocollect Hardware Documentation Vocollect Battery Safety Improper use of the battery may cause heat, fire, explosion, damage, or reduced battery capacity. Read and follow the handling instructions for the battery before and during use. The following are general cautions and guidelines only, and as such may not include every possible usage scenario. The manufacturer will not be liable for actions taken or accidents caused by any use not documented below.
Introduction | 19 • Store batteries in a rugged receptacle and cover with a lid. Cleaning Procedures for Vocollect Equipment Vocollect products have a long service life if they are maintained properly. Proper care includes following recommended cleaning practices and procedures. While Vocollect equipment is manufactured and tested to be resistant to normal dirt and deposits from the workplace environment, the build-up of residue can damage the equipment over time.
20 | Vocollect Hardware Documentation Caution: Vocollect recommends using only a solution of 30% isopropyl alcohol and water to cleaning equipment. Other products have not been tested and may degrade the equipment. Flat contact areas on the device, such as the Talkman Connector (TCO), or flat contacts on the battery and charger should be cleaned with the recommended isopropyl alcohol solution. Use a soft, lint-free cloth or premoistened alcohol wipe.
Introduction | 21 United States Phone: 866-862-6553, option 3, option 2 Email: voccustsupp@vocollect.com Europe, Middle East, Africa Phone: +44 (0) 1628 55 2903 Email: CustomerServicesEMEA@vocollect.com Americas (outside U.S.) Australia, New Zealand Phone: 412-829-8145, option 3, option 2 Email: voccustsupp@vocollect.com Japan and Korea Phone: +813 3769 5601 Email: japan@vocollect.
22 | Vocollect Hardware Documentation • D549,216; D525,237; D549,217; D529,438; D530,667; D551,615; D549,694; D552,595; D554,642. Other U. S. and worldwide patents pending.
Chapter 2 Talkman Devices and Headsets Vocollect Talkman® devices are wearable terminals used with Vocollect headsets to enable voice-directed work. Operators listen to instructions from these devices to perform tasks such as warehouse order picking and factory floor inspection, and then speak simple phrases to enter data. All Talkman devices leave the operator's hands free to inspect items, pick products, drive vehicles, or repair defects.
24 | Vocollect Hardware Documentation More Product Care Information • See Cleaning Procedures for Vocollect Equipment for proper care of plastics and contacts. • See Care and Use of Headsets and Microphones for more information on these products.
Talkman Devices and Headsets | 25 • Booting a Device After Powering Off If a device was properly powered off, it does the following operations after a battery is placed into the device and the Play/Pause button is pressed: • • • • • Performs a background noise sample Continues operation at the place in the task where you left off Transfers any templates to the host that had not been sent prior to powering off Transfers any output data records to the host that had not been sent prior to powering off Transf
26 | Vocollect Hardware Documentation • When selecting a team in step 5, choose the "All Operators" team. • Consult with your supervisor if you are not listed in the "All Operators" team. 8. Press the operator button. The device says, "Loading operator" and loads your templates. Once it has loaded your templates, the device says, "Current operator is (your operator name). Good night." The device then goes to sleep. The next time you turn the device on, it will be ready to use.
Talkman Devices and Headsets | 27 If the device says "This is softest" or "This is loudest", you cannot make the volume any louder or softer. 3. When the voice is as loud or as soft as you want it, say "Talkman continue" to return to work. Adjusting the Volume Using Device Buttons Make sure the device is on or sleeping. The LED indicator should be either solid green or blinking green (A500, T5-series and T2-series) or solid green (T1).
28 | Vocollect Hardware Documentation 5. When you hear the speaker you want to use, press the Operator button to select that speaker. Understanding Talkman Commands The Talkman device prompts the operator for responses that are specific to the voice-directed work he or she is performing. Several basic Talkman commands, however, can be spoken by the operator at almost any time while using the device. You want to...
Talkman Devices and Headsets | 29 Accessory Vocollect Part Number T5/A500 Clip BL-700-101B (For use with BL-700-1 - BL-700-7 and HL-700-1) T2 Belt with Clip Belts: BL-601-101-7 T2 Clip BL-602-101 T1 Holster BL-100-101 A500/T5 High-Performance Battery T2 Series Standard Battery BT-700-2 BT-601 T2 Series High-Capacity Battery BT-602 T1 Standard Battery BT-101 Vehicle Mount, Holder, Talkman A500/T5 Series BL-710-1 Vehicle Mount, Holder/Base Screw On Attachment, Talkman A500/T5 Series BL-710
30 | Vocollect Hardware Documentation Customer User SL-4/ SR-15 SR-20 X X X X SR-30 SR-35 SR-40 SRX SRX2 X X SL-14 General use headset Light industrial/customer facing X Freezer use Behind the head X X X X X X X X X High noise areas Use with hard hat X X X Wireless X Extreme (large/small) head size X X Extreme (large/small) ear size X X X X X X X X Part Numbers: Wired Headsets Part Numbers for ordering Vocollect headsets and accessories All wired headsets come wi
Talkman Devices and Headsets | 31 Part Numbers: Wired Headset Accessories Part Numbers for ordering Vocollect headset supplies Part (SL-4/SL-14 Wired Headset) Part Number Windscreen, SL-Series Headsets (Bag of 50) HS-708-102b Cord Clips, SL-Series Headsets (Bag of 20) HS-708-103b Training Poster (English), SL-4/14 PK-HS-708-4-2 Training Poster (English), SL-4/14 PK-HS-708-14-2 Part (SR-15 Wired Headset) Part Number Windscreen, SR-Series Headsets (Bag of 25) HD-700-102b Cord Clip, SR-Series He
32 | Vocollect Hardware Documentation Part (SR-30/31 Wired Headset) Part Number Windscreen, SR-Series Headsets (Bag of 25) HD-700-102b Cord Clip, SR-Series Headsets (Bundle of 10) HD-700-103b T-Bar Pad, SR-Series Headsets (Bag of 25) HD-700-106b Headband Pads, SR-20 (Bag of 30) HD-700-109b Maintenance Kit, SR-30, 31, 35, and 40 (15 foam ear pads, 30 headband pads, HD-702-101 and 5 ear pad mounting disks) Earpad, Smooth Leatherette, SR-30, 31, 35, and 40 (Bag of 10) HD-702-102b Earpad, Textured
Talkman Devices and Headsets | 33 Part (Various Wired Headsets) Part Number ® Vocollect Headset Adapter, Symbol MC9060-S to Vocollect Breakaway Connector, Replacement Mount Plate Assembly AD-100-101 Part Numbers: Wireless Headsets Part Numbers for ordering Vocollect headsets and accessories Part Part Number SRX Speech Recognition Headset Complete HD-800-1 SRX2 Headset 1 Complete Headset, 1 Battery (1 headband, all pads and strap, BUNDLE-HD-1000-1 1 electronics module, 1 battery, 1 mic cap) SRX2 Hea
34 | Vocollect Hardware Documentation Part (SRX Wireless Headset) Part Number SRX Training Poster Kit (English), automatic and manual pairing, poster and SK-700 cards Part (SRX2 Wireless Headset) Part Number SRX2 Electronics Module HD-1000-101 SRX2 Headband with Stability Strap (not assembled) HD-1000-102 SRX2 Electronics Module Storage Rack HD-1000-103 SRX2 Microphone Caps (Bag of 20) HD-1000-104B SRX2 Ear Pads (Bag of 20) HD-1000-105B SRX2 Comfort Pads (Bag of 20) HD-1000-106B SRX2 T-Bar
Talkman Devices and Headsets | 35 Charger Vocollect Part Number SRX 5-Bay Battery Charger CM-801-1 SRX Single-Bay Battery Charger CM-800-1 SRX2 20-Bay Battery Charger CM-1000-20 SRX2 Charger DIN Rail, 550 mm length CM-1000-20-1 Confidential: For informational use by Vocollect Resellers and customers only
Chapter 8 Vocollect Wireless Headsets An operator uses a headset with a microphone to interact with a device by hearing and responding to instructions. Based on the operator's responses, the device transmits data messages back to the host computer. The Vocollect ® SRX-Series speech-recognition headsets feature industrial grade use of Bluetooth Wireless Technology.
116 | Vocollect Hardware Documentation Vocollect SRX Wireless Headset Figure 80: SRX Wireless Headset The Vocollect ® SRX speech-recognition headset features industrial grade use of Bluetooth Wireless Technology. The SRX headset manages the quality of voice input/output in the headset itself, has no cables to connect, and remains connected to a device at up to 10 meters away. • Pairing modes on the headset can only be entered from the powered off state.
Vocollect Wireless Headsets | 117 Humidity 5-95% non-condensing Noise Reduction Rating Not applicable Charging the SRX Headset Figure 81: SRX Wireless Headset High-Performance Battery A fully depleted SRX Wireless Headset battery will be fully recharged in less than 4 hours. A fully charged SRX Wireless Headset battery has 3.7 volts. When the charge depletes to 3.3 volts, the user will hear a spoken warning, "Headset battery is getting low. Change headset battery now.
118 | Vocollect Hardware Documentation on the charger is red. It may take several minutes for this process to complete, at which time both LED indicators for that slot turn green. 1. Make sure the battery charger is powered. The green LED indicator on the end of the battery charger should be lit. 2. Power off the headset by pressing and holding the Plus and Minus buttons on the earpiece for three seconds and then remove the battery. 3.
Vocollect Wireless Headsets | 119 Installing the SRX Mobility Strap 1. Remove the battery from the SRX Wireless Headset. 2. Feed the lanyard end of the mobility strap through one of the eyelets in the headset's battery compartment. You may find it helpful to push the lanyard through with the tip of a screwdriver. Be sure to feed the lanyard in the direction shown in the image. Figure 82: Feeding the Lanyard Through an Eyelet 3. Feed the lanyard back through the other eyelet in the battery compartment.
120 | Vocollect Hardware Documentation Figure 85: Clipping the Strap to the Loop Wearing an SRX Wireless Headset Make sure the Velcro mobility strap is installed on the headset. 1. Put the headset on and adjust the ear pad to fit snugly over your ear. 2. Position the battery compartment directly above, and as closely as possible to, your other ear. 3. Adjust the mobility strap so it fits securely across the back of your head. Figure 86: Mobility Strap Worn Properly 4.
Vocollect Wireless Headsets | 121 Figure 87: Moving the Microphone Into Position 5. Make final adjustments with the flexible boom so that the microphone is positioned at the corner of your mouth, about 1/4" away from your face. Headset Functions and LED Patterns for SRX Headset Function User Action Headset Mode LED Pattern Power On Hold the Plus (+) and Minus (-) buttons for one second Headset powers on and Quick flutter searches for the previously-connected device. No new pairing takes place.
122 | Vocollect Hardware Documentation Headset Function User Action Force disconnect for manual pairing in low power mode Switch to high power pairing when pairing in low power mode has failed Headset Mode LED Pattern Tone Hold the Plus Headset disconnects current (+) and Minus pairing and enters low power (-) buttons for pairing mode four seconds Headset attempts to pair with the nearest un-paired Bluetooth device. Previous pairing erased from headset's memory.
Vocollect Wireless Headsets | 123 Headset Function User Action Headset Mode LED Pattern Tone Low Battery N/A Headset automatically enters this mode when the battery's remaining charge reaches a minimum threshold. Constant very quick No tone. flutter (about 10 Voice prompt: flashes per second). "Headset battery is getting low," or Note: When "Headset battery the LED is blinking in Low is getting low. Battery mode, Change headset no other LED battery now.
124 | Vocollect Hardware Documentation In addition, the modular design of the headset enables a much lower cost per user through the shared use of headset electronic modules across multiple shifts. Other features include: • Faster, easier pairing with Vocollect TouchConnect™ Technology (with RFID reader equipped Voice-enabled devices) • Enhanced data rates with Bluetooth Version 2.1 • Headset tracking and management with VoiceConsole 4.
Vocollect Wireless Headsets | 125 Figure 89: SRX2 headset and electronics module Figure 90: Removing mic cap and stowing in mic cap pocket Attaching the SRX2 Electronics Module to a Headband 1. Position the SRX2 electronics module with the button controls facing away from the headband. 2. Insert the speaker on the back of the electronics module into the pocket on the earpiece hub by aligning the notches on the speaker and hub pocket. Figure 91: Attaching the electronics module 3.
126 | Vocollect Hardware Documentation Removing the SRX2 Electronics Module from a Headband Important: Do not squeeze the battery latches on the sides of the electronics module while removing it from the headband. The battery may be inadvertently released from the electronics module. 1. Grasp the SRX2 electronics module with one hand, pressing your thumb and fingertips into the gap between the electronics module and earpiece hub. 2. With the other hand, hold the headband by the earpiece hub. 3.
Vocollect Wireless Headsets | 127 Battery Condition Audio Warning When battery voltage is low "Headset battery is getting low." When battery voltage is critically low and about to turn off “Headset battery is getting low. Change headset battery now.” SRX2 Battery Specifications Electrical Specifications • Cells: The battery pack uses a single lithium ion cell. • Nominal voltage = 3.6V • Watt hours = 2.
128 | Vocollect Hardware Documentation • If you insert a fully charged battery into a charger, the charger will analyze the battery's status and then "top off" the battery's charge. The ring LED indicator light for that port will be yellow during this process. When complete, the ring LED indicator will turn green. 1. Make sure the battery charger is powered. To power on the charger, connect the power supply to the charger and a power source.
Vocollect Wireless Headsets | 129 1. Power off the headset by pressing and holding the Power button on the electronics module for one second. 2. Grasp the headset by the sides of the electronics module with your thumb and fingers on the black battery latches. Figure 93: Battery Latches for Removing SRX2 Battery 3. With your other hand, hold the battery at the end of the electronics module opposite the mic boom. 4.
130 | Vocollect Hardware Documentation Figure 94: Wearing the SRX2 headset 2. Position the t-bar directly above, and as closely as possible to, your other ear. 3. If installed, adjust the stability strap so it fits securely across the back of your head. 4. Rotate the electronics module up or down to position the microphone near your mouth. Figure 95: Moving the Microphone Into Position 5.
Vocollect Wireless Headsets | 131 Figure 96: Pressing the strap onto the earpad side of the headband 4. 5. 6. 7. Turn the headset so that the t-bar pad faces you. Locate the slot on the end of the headband near the t-bar. Align the knob at the free end of the strap with the slot on the headband. Slide the knob into the slot until it snaps into place. Figure 97: Inserting the strap into the headband slot 8. Position the strap to go around the back of your head.
132 | Vocollect Hardware Documentation Figure 98: Installing a new earpad 5. Place the new earpad and earpad plate assembly onto the headset earpiece. 6. Rotate the assembly to the right pressing gently into the earpiece until the assembly locks into place.
Vocollect Wireless Headsets | 133 Headset Function User Action Headset Mode LED Pattern Tone connected, device says, "louder." Decrease volume Press the Minus (-) button N/A N/A Two tone descending sequence. If connected, device says, "softer." Force disconnect for manual pairing in low power mode With headset connected, press the Plus (+) and Minus (-) buttons Headset disconnects current pairing and enters low power pairing mode Solid green No tone when entering mode.
134 | Vocollect Hardware Documentation Vocollect Headset Software Update Tool With the introduction of its SRX2 Wireless Headset, Vocollect developed the Vocollect Headset Software Update Tool. Part of maintaining the SRX2 headset involves an occasional software update of the Bluetooth chipset. Vocollect releases these updates when they become available.
Vocollect Wireless Headsets | 135 c) Browse to the USBDrivers folder on the installation DVD. d) Complete the installation. USB Driver Installation on Windows 7 or Windows 2008 a) b) c) d) e) Launch Device Manager and navigate to Bluetooth Radios > Generic Bluetooth Adapters. Right-click and select the "Update Driver Software" menu option. Select "Locate and install driver software manually." Select "Let me pick from a list of device drivers on my computer." Click the Have Disk...
136 | Vocollect Hardware Documentation • The software update file(s) have been copied to the local machine or an accessible network resource. 1. Connect one or more SRX2 headsets and/or a single SRX2 battery charger to the system via USB cables. Ensure that each SRX2 headset has a charged battery inserted prior to running the software update. A charger update can be performed with batteries mounted on the charger ports and charging.
Vocollect Wireless Headsets | 137 • To update all devices listed, click the Update All button in the toolbar. Important: Do not disconnect the headsets or chargers during the update process. 7. Check the update results. When the upgrade completes, the State field shows "finished" and the Progress field shows 100 percent for the devices being updated. a) Check the notifications on the screen for the success or failure status of each device.
138 | Vocollect Hardware Documentation Note: The SRX2 headset always powers up in pairing mode. Manual pairing: The user determines when to pair a device and headset by pressing buttons on the device. Manual pairing is effective in environments where the same Talkman devices and headsets are always used together. Important: The first pairing for an SRX headset that has never been paired with a device must be a manual pairing. After this first time, the headset can pair automatically.
Vocollect Wireless Headsets | 139 The LED indicator on the headset flutters quickly, plauses, flashes three times quickly, then starts flashing slowly. The headset remains in pairing mode for about one minute then reverts to idle mode. 3. Hold the headset and Talkman device so they are within six inches of each other but not touching. The blue LED indicator on the Talkman device turns on, may flash a few times, and then remains lit.
140 | Vocollect Hardware Documentation • The headset is powered off. You can only put an SRX Wireless Headset into low or high power pairing mode from the powered-off state. • The handheld device is not in a charger, and there is no wired headset connected to it. • The device is in sleep mode — not in use running an application. • The device is Bluetooth ready with Bluetooth connection features enabled. 1.
Vocollect Wireless Headsets | 141 Auto Pairing with a Talkman Device Prerequisites: • The headset is powered off. • There is no wired headset connected to the Talkman device. • The Talkman device is Bluetooth ready with Bluetooth connection features enabled. Important: An unpaired Talkman device will constantly search for wireless headsets while in auto pairing mode. Do not leave an auto pair-enabled device unpaired and powered on because the search will drain the battery. 1.
142 | Vocollect Hardware Documentation 5. Verify that the number matches the serial number on the Talkman device. If you need to attempt the pairing again, re-enter pairing mode by press the Plus (+) and Minus (-) buttons on the Talkman device again. 6. Press the Play/Pause button on the Talkman device to confirm the number. 7. Press the Play/Pause button again to begin working.
Vocollect Wireless Headsets | 143 Pairing a Headset by VoiceConsole Pairing The VoiceConsole pairing method should only be used if the device/headset pairing will be performed once and never changed. While manual pairing can also result in this permanent pairing, VoiceConsole eliminates the device inquiry step and begins paging immediately for the Bluetooth address. Prerequisites: • • • • The headset is powered off. The device is not in a charger, and there is no wired headset connected to it.
144 | Vocollect Hardware Documentation Placing Headsets in Pairing Modes Initial Headset SRX Controls State Off SRX2 Controls Press and hold Plus (+) and N/A Minus (-) buttons for 0 to 3 seconds Pairing Mode Result Idle mode Mode only allows connection with the last device paired Off Press and hold Plus (+) and Press and release Power Low power pairing mode Minus (-) buttons for 4 to 6 button seconds Off Press and hold Plus (+) and N/A Minus (-) buttons for 7 or more seconds High power pairing mode
Vocollect Wireless Headsets | 145 Q: The users at my site do not have assigned headsets and devices, so they could get a different headset at every shift. Which pairing process would you recommend? A: Auto pairing would probably be the easiest, as it will quickly establish connections and, by default, does not maintain those pairings. Q: The users at my site are assigned their own SRX-Series headsets, so I want to maintain pairings and avoid pairing headsets at the start of every shift.
146 | Vocollect Hardware Documentation Configuration Parameters for SRX-Series Headsets Parameter Supported Description Devices Values & Setting Location Bluetooth_IsEnabled A500, Determines whether or not the T5-Series Bluetooth portion of the radio is receiving power. When the value for this setting is set to false, the Bluetooth portion of the radio receives no power, and no other Bluetooth parameters are active.
Vocollect Wireless Headsets | 147 Parameter Supported Description Devices Values & Setting Location Users may prefer to disable headsets when using other Bluetooth peripherals. SrxHighPowerPairingDelaySeconds Psion, Specifies how long (in seconds) Intermec an operator is required to hold the plus and minus buttons on an SRX headset while in low power pairing mode before entering high power pairing mode. Not used for SRX2 headsets.
148 | Vocollect Hardware Documentation Check the documentation for your release of Vocollect Voice software to verify if these settings are supported. Care and Use of Headsets and Microphones The headsets and microphones used with the Vocollect Voice system are delicate pieces of electronic equipment. Proper care and use of these products will ensure that they work well for a long time. Important: For maximum hygiene, Vocollect discourages sharing headsets among operators.
Vocollect Wireless Headsets | 149 As an operator speaks, the muscle above the ear flexes. If the t-bar is placed on this muscle, the headset applies pressure to the artery and nerves beneath it and can cause the operator some discomfort. The operator can locate this muscle by moving his or her jaw and feeling the area above the ear for movement. Some operators choose to alternate the headset position on either side of their heads during their shifts.
150 | Vocollect Hardware Documentation 3. Squeeze out the excess water and let it air dry thoroughly. Cleaning Headsets Note: Commercial cleaning solvents are not recommended. • Clean the plastic parts of the headsets with a soft cloth dampened with water. To clean and disinfect the headset plastic, use a pre-moistened alcohol wipe. • If the Talkman Connectors or plugs become contaminated, use a pre-moistened alcohol wipe to remove dirt or residue.
Appendix A Compliance Vocollect® Regulatory Compliance Statement of Agency Compliance Vocollect devices, and wireless headsets are designed to be compliant with the rules and regulations in the locations into which they are sold and are labeled as required. Vocollect devices are type approved and do not require the user to obtain license or authorization before using them. Changes or modifications not expressly approved by Vocollect, Inc. could void the user's authority to operate the equipment.
258 | Vocollect Hardware Documentation Vocollect products contain one of the following radio devices. See device label. Vocollect Device Card FCC ID# Manufacturer and P/N Canadian ID # Maximum SAR Value (1 gram average) Maximum SAR Value (10 gram average) T2x Vocollect Wi-Fi Model: TT-600 600-2400-032 T2x Summit SDC-CF10G MQOTT601-30000 2570A-TT601300 0.531W/kg No data available USI WM-BB-AG-01 MQOTT700-10000 MQOTT700-10000 0.471W/kg No data available MQOTT600-50300 2570A-TT60-50300 0.
Compliance | 259 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage. 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
260 | Vocollect Hardware Documentation The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Vocollect is under license. Other trademarks and trade names are those of their respective owners. Made in the U.S.A.
