6.5.1
Table Of Contents
- vSphere Storage
- Contents
- About vSphere Storage
- Updated Information
- Introduction to Storage
- Getting Started with a Traditional Storage Model
- Overview of Using ESXi with a SAN
- Using ESXi with Fibre Channel SAN
- Configuring Fibre Channel Storage
- Configuring Fibre Channel over Ethernet
- Booting ESXi from Fibre Channel SAN
- Booting ESXi with Software FCoE
- Best Practices for Fibre Channel Storage
- Using ESXi with iSCSI SAN
- Configuring iSCSI Adapters and Storage
- ESXi iSCSI SAN Requirements
- ESXi iSCSI SAN Restrictions
- Setting LUN Allocations for iSCSI
- Network Configuration and Authentication
- Set Up Independent Hardware iSCSI Adapters
- About Dependent Hardware iSCSI Adapters
- About the Software iSCSI Adapter
- Modify General Properties for iSCSI Adapters
- Setting Up iSCSI Network
- Using Jumbo Frames with iSCSI
- Configuring Discovery Addresses for iSCSI Adapters
- Configuring CHAP Parameters for iSCSI Adapters
- Configuring Advanced Parameters for iSCSI
- iSCSI Session Management
- Booting from iSCSI SAN
- Best Practices for iSCSI Storage
- Managing Storage Devices
- Storage Device Characteristics
- Understanding Storage Device Naming
- Storage Rescan Operations
- Identifying Device Connectivity Problems
- Edit Configuration File Parameters
- Enable or Disable the Locator LED on Storage Devices
- Erase Storage Devices
- Working with Flash Devices
- About VMware vSphere Flash Read Cache
- Working with Datastores
- Types of Datastores
- Understanding VMFS Datastores
- Understanding Network File System Datastores
- Creating Datastores
- Managing Duplicate VMFS Datastores
- Increasing VMFS Datastore Capacity
- Administrative Operations for Datastores
- Set Up Dynamic Disk Mirroring
- Collecting Diagnostic Information for ESXi Hosts on a Storage Device
- Checking Metadata Consistency with VOMA
- Configuring VMFS Pointer Block Cache
- Understanding Multipathing and Failover
- Raw Device Mapping
- Software-Defined Storage and Storage Policy Based Management
- About Storage Policy Based Management
- Virtual Machine Storage Policies
- Working with Virtual Machine Storage Policies
- Populating the VM Storage Policies Interface
- Default Storage Policies
- Creating and Managing VM Storage Policies
- Storage Policies and Virtual Machines
- Assign Storage Policies to Virtual Machines
- Change Storage Policy Assignment for Virtual Machine Files and Disks
- Monitor Storage Compliance for Virtual Machines
- Check Compliance for a VM Storage Policy
- Find Compatible Storage Resource for Noncompliant Virtual Machine
- Reapply Virtual Machine Storage Policy
- Using Storage Providers
- Working with Virtual Volumes
- About Virtual Volumes
- Virtual Volumes Concepts
- Virtual Volumes and Storage Protocols
- Virtual Volumes Architecture
- Virtual Volumes and VMware Certificate Authority
- Snapshots and Virtual Volumes
- Before You Enable Virtual Volumes
- Configure Virtual Volumes
- Provision Virtual Machines on Virtual Volumes Datastores
- Virtual Volumes and Replication
- Best Practices for Working with vSphere Virtual Volumes
- Filtering Virtual Machine I/O
- Storage Hardware Acceleration
- Hardware Acceleration Benefits
- Hardware Acceleration Requirements
- Hardware Acceleration Support Status
- Hardware Acceleration for Block Storage Devices
- Hardware Acceleration on NAS Devices
- Hardware Acceleration Considerations
- Thin Provisioning and Space Reclamation
- Using vmkfstools
- vmkfstools Command Syntax
- The vmkfstools Command Options
- -v Suboption
- File System Options
- Virtual Disk Options
- Supported Disk Formats
- Creating a Virtual Disk
- Initializing a Virtual Disk
- Inflating a Thin Virtual Disk
- Converting a Zeroedthick Virtual Disk to an Eagerzeroedthick Disk
- Removing Zeroed Blocks
- Deleting a Virtual Disk
- Renaming a Virtual Disk
- Cloning or Converting a Virtual Disk or RDM
- Extending a Virtual Disk
- Upgrading Virtual Disks
- Creating a Virtual Compatibility Mode Raw Device Mapping
- Creating a Physical Compatibility Mode Raw Device Mapping
- Listing Attributes of an RDM
- Displaying Virtual Disk Geometry
- Checking and Repairing Virtual Disks
- Checking Disk Chain for Consistency
- Storage Device Options
For the software FCoE adapter, you must properly configure networking and then activate the adapter.
Note The number of software FCoE adapters you activate corresponds to the number of physical NIC
ports. ESXi supports a maximum of four software FCoE adapters on one host.
Configuration Guidelines for Software FCoE
When setting up your network environment to work with ESXi software FCoE, follow the guidelines and
best practices that VMware offers.
Network Switch Guidelines
Follow these guidelines when you configure a network switch for software FCoE environment:
n
On the ports that communicate with your ESXi host, disable the Spanning Tree Protocol (STP).
Having the STP enabled might delay the FCoE Initialization Protocol (FIP) response at the switch and
cause an all paths down (APD) condition.
The FIP is a protocol that FCoE uses to discover and initialize FCoE entities on the Ethernet.
n
Turn on Priority-based Flow Control (PFC) and set it to AUTO.
n
Make sure that you have a compatible firmware version on the FCoE switch.
Network Adapter Best Practices
If you plan to enable software FCoE adapters to work with network adapters, specific considerations
apply.
n
Make sure that the latest microcode is installed on the FCoE network adapter.
n
If the network adapter has multiple ports, when configuring networking, add each port to a separate
vSwitch. This practice helps you to avoid an APD condition when a disruptive event, such as an MTU
change, occurs.
n
Do not move a network adapter port from one vSwitch to another when FCoE traffic is active. If you
need to make this change, reboot your host afterwards.
n
If you changed the vSwitch for a network adapter port and caused a failure, moving the port back to
the original vSwitch resolves the problem.
Set Up Networking for Software FCoE
Before you activate the software FCoE adapters, create VMkernel network adapters for all physical FCoE
NICs installed on your host.
This procedure explains how to create a single VMkernel network adapter connected to a single FCoE
physical network adapter through a vSphere Standard switch. If your host has multiple network adapters
or multiple ports on the adapter, connect each FCoE NIC to a separate standard switch. For more
information, see the vSphere Networking documentation.
vSphere Storage
VMware, Inc. 48