8.0
Table Of Contents
- VMware ESXi Installation and Setup
- Contents
- About VMware ESXi Installation and Setup
- Introduction to vSphere Installation and Setup
- Introducing VMware vSphere Distributed Services Engine and Networking Acceleration by Using DPUs
- Installing and Setting Up ESXi
- ESXi Requirements
- Preparing for Installing ESXi
- Customizing Installations with vSphere ESXi Image Builder
- How the vSphere ESXi Image Builder Works
- Structure of ImageProfile, SoftwarePackage, and ImageProfileDiff Objects
- Install Prerequisite Software and Configure vSphere ESXi Image Builder
- Using VMware.Image Builder Cmdlets
- ESXi Image Profile Tasks
- Add a Software Depot
- Import a Software Depot
- Clone an Image Profile
- Create an Image Profile
- Edit an Image Profile
- Compare Image Profiles
- Move an Image Profile to a Different Software Depot
- Export an Image Profile to ISO or Offline Bundle ZIP
- Regenerate an Image Profile
- Preserve Image Profiles Across Sessions with PowerCLI Cmdlets
- Compare VIBs with PowerCLI Cmdlets
- vSphere ESXi Image Builder Workflows with PowerCLI Cmdlets
- Installing ESXi
- Installing ESXi Interactively
- Installing ESXi by Using a Script
- How to Boot an ESXi Host from a Network Device
- Installing ESXi Using vSphere Auto Deploy
- Understanding vSphere Auto Deploy
- Install and Configure vSphere Auto Deploy
- How vSphere Auto Deploy Works with PowerCLI
- Managing vSphere Auto Deploy with PowerCLI Cmdlets
- Overview of the vSphere Auto Deploy Process by Using PowerCLI
- Using vSphere Auto Deploy Cmdlets
- vSphere Auto Deploy PowerCLI Cmdlet Overview
- Assign an Image Profile to Hosts
- Write a Rule and Assign a Host Profile to Hosts
- Write a Rule and Assign a Host to a Folder or Cluster
- Configure a Stateless System by Running a Custom Script
- Test and Repair Rule Compliance
- Register a Caching Proxy Server Address with vSphere Auto Deploy
- vSphere Auto Deploy Tasks by Using the vSphere Client
- Managing vSphere Auto Deploy with the vSphere Client
- Create a Deploy Rule
- Clone a Deploy Rule
- Edit a Deploy Rule
- Activate, Deactivate, and Reorder Deploy Rules
- View Host Associations
- Edit the Image Profile Association of a Host
- Remediate a Non-compliant Host
- Add a Host to the vSphere Auto Deploy Inventory
- Add a Host to a Cluster That Uses a Single Image
- Add a Host to a Cluster That Manages ESXi Configuration at a Cluster Level
- Working with Script Bundles
- Download vSphere Auto Deploy Logs
- Start, Stop, or Restart the vSphere Auto Deploy Service
- Provision and Reprovision ESXi Hosts with vSphere Auto Deploy
- Using vSphere Auto Deploy for Stateless Caching and Stateful Installs
- Configure a Host Profile to Use Stateless Caching
- Configure a Host Profile to Enable Stateful Installs
- Setting Up a vSphere Auto Deploy Reference Host
- Configure an ESXi Dump Collector
- Configure Syslog from the Host Profiles Feature in the vSphere Client
- Enable NTP Client on a Reference Host in the vSphere Client
- Configure Networking for Your vSphere Auto Deploy Host in the vSphere Client
- Configure a Reference Host for Auto-Partitioning
- Converting Stateless Hosts to Stateful Hosts
- vSphere Auto Deploy Best Practices and Security Consideration
- Scenario to Set Up vSphere Auto Deploy and Provision Hosts with vSphere PowerCLI
- Install the TFTP Server
- Install PowerCLI
- Prepare the vSphere Auto Deploy Target Hosts
- Prepare the DHCP Server for vSphere Auto Deploy Provisioning
- Configure the vSphere Auto Deploy and TFTP Environment in the vSphere Client
- Prepare the ESXi Software Depot and Write a Rule
- Provision the First Host with vSphere Auto Deploy
- Extract and Configure a Host Profile from the Reference Host
- Create a Rule that Provisions Hosts from a Specific IP Range
- Provision Hosts and Set Up Host Customizations
- Troubleshooting vSphere Auto Deploy
- vSphere Auto Deploy Rule Takes Long to Complete
- vSphere Auto Deploy TFTP Timeout Error at Boot Time
- vSphere Auto Deploy Host Boots with Wrong Configuration
- Host Is Not Redirected to vSphere Auto Deploy Server
- Package Warning Message When You Assign an Image Profile to a vSphere Auto Deploy Host
- vSphere Auto Deploy Host with a Built-In USB Flash Drive Does Not Send Coredumps to Local Disk
- vSphere Auto Deploy Host Reboots After Five Minutes
- vSphere Auto Deploy Host Cannot Contact TFTP Server
- vSphere Auto Deploy Host Cannot Retrieve ESXi Image from vSphere Auto Deploy Server
- vSphere Auto Deploy Host Does Not Get a DHCP Assigned Address
- vSphere Auto Deploy Host Does Not Network Boot
- Recovering from Database Corruption on the vSphere Auto Deploy Server
- Setting Up ESXi
- Initial ESXi Configuration
- ESXi Autoconfiguration
- Managing ESXi Remotely
- About the Direct Console ESXi Interface
- Configure the Keyboard Layout for the Direct Console
- Create a Security Banner for the Direct Console
- Redirecting the Direct Console to a Serial Port
- Redirect the Direct Console to a Serial Port by Setting the Boot Options Manually
- Redirect the Direct Console to a Serial Port in a Host Deployed with Auto Deploy
- Enable ESXi Shell and SSH Access with the Direct Console User Interface
- Set the Password for the Administrator Account
- Configuring the BIOS Boot Settings
- Configuring Network Settings
- Network Access to Your ESXi Host
- ESXi Networking Security Recommendations
- Choose Network Adapters for the Management Network
- Set the VLAN ID
- Configuring IP Settings for ESXi
- Configure IP Settings from the Direct Console
- Configure IP Settings from the vSphere Client
- Configuring DNS for ESXi
- Configure DNS Settings from the Direct Console
- Configure DNS Suffixes
- Configure the Network Settings on a Host That Is Not Attached to the Network
- Test the Management Network
- Restart the Management Agents
- Restart the Management Network
- Test Connectivity to Devices and Networks
- Restoring the Standard Switch
- Configuring System Logging
- Set the Host Image Profile Acceptance Level
- Remove All Custom Packages on ESXi
- Deactivate Support for Non-ASCII Characters in Virtual Machine File and Directory Names
- Reset the System Configuration
- Initial ESXi Configuration
- After You Install and Set Up ESXi
- Troubleshooting ESXi Booting
- Decommission an ESXi Host
Prerequisites
n Decide which disk to use for storing the image, and determine whether the new image will
overwrite an existing VMFS partition.
n Set up your environment for vSphere Auto Deploy. See Install and Configure vSphere Auto
Deploy.
n Verify that a disk with at least 4GB of free space is available. If the disk is not yet partitioned,
partitioning happens when you apply the host profile.
n Set up the host to boot from disk. See your hardware vendor's documentation.
n Create a host profile. See the
Host Profiles
documentation.
Procedure
1 Navigate to Home > Policies and Profiles > Host Profiles.
2 Click the host profile you want to configure and select the Configure tab.
3 Click Edit Host Profile.
4 On the Edit host profile page of the wizard, select Advanced Configuration Settings > System
Image Cache Configuration > System Image Cache Configuration.
5 In the System Image Cache Profile Settings drop-down menu, choose a policy option.
Option
Description
Enable stateful installs on the host Caches the image to a disk.
Enable stateful installs to a USB disk
on the host
Caches the image to a USB disk attached to the host.
VMware ESXi Installation and Setup
VMware, Inc. 174