6.5
Table Of Contents
- vSphere Command-Line Interface Concepts and Examples
- Contents
- About This Book
- vSphere CLI Command Overviews
- Introduction
- List of Available Host Management Commands
- Targets and Protocols for vCLI Host Management Commands
- Supported Platforms for vCLI Commands
- Commands with an esxcfg Prefix
- ESXCLI Commands Available on Different ESXi Hosts
- Trust Relationship Requirement for ESXCLI Commands
- Using ESXCLI Output
- Connection Options for vCLI Host Management Commands
- Connection Options for DCLI Commands
- vCLI Host Management Commands and Lockdown Mode
- Managing Hosts
- Managing Files
- Managing Storage
- Introduction to Storage
- Examining LUNs
- Detach a Device and Remove a LUN
- Reattach a Device
- Working with Permanent Device Loss
- Managing Paths
- Managing Path Policies
- Scheduling Queues for Virtual Machine I/O
- Managing NFS/NAS Datastores
- Monitor and Manage FibreChannel SAN Storage
- Monitoring and Managing Virtual SAN Storage
- Monitoring vSphere Flash Read Cache
- Monitoring and Managing Virtual Volumes
- Migrating Virtual Machines with svmotion
- Configuring FCoE Adapters
- Scanning Storage Adapters
- Retrieving SMART Information
- Managing iSCSI Storage
- iSCSI Storage Overview
- Protecting an iSCSI SAN
- Command Syntax for esxcli iscsi and vicfg-iscsi
- iSCSI Storage Setup with ESXCLI
- iSCSI Storage Setup with vicfg-iscsi
- Listing and Setting iSCSI Options
- Listing and Setting iSCSI Parameters
- Enabling iSCSI Authentication
- Set Up Ports for iSCSI Multipathing
- Managing iSCSI Sessions
- Managing Third-Party Storage Arrays
- Managing Users
- Managing Virtual Machines
- Managing vSphere Networking
- Introduction to vSphere Networking
- Retrieving Basic Networking Information
- Troubleshoot a Networking Setup
- Setting Up vSphere Networking with vSphere Standard Switches
- Setting Up Virtual Switches and Associating a Switch with a Network Interface
- Retrieving Information About Virtual Switches
- Adding and Deleting Virtual Switches
- Checking, Adding, and Removing Port Groups
- Managing Uplinks and Port Groups
- Setting the Port Group VLAN ID
- Managing Uplink Adapters
- Adding and Modifying VMkernel Network Interfaces
- Managing VMkernel Network Interfaces with ESXCLI
- Add and Configure an IPv4 VMkernel Network Interface with ESXCLI
- Add and Configure an IPv6 VMkernel Network Interface with ESXCLI
- Managing VMkernel Network Interfaces with vicfg-vmknic
- Add and Configure an IPv4 VMkernel Network Interface with vicfg-vmknic
- Add and Configure an IPv6 VMkernel Network Interface with vicfg-vmknic
- Setting Up vSphere Networking with vSphere Distributed Switch
- Managing Standard Networking Services in the vSphere Environment
- Setting the DNS Configuration
- Manage an NTP Server
- Manage the IP Gateway
- Setting Up IPsec
- Manage the ESXi Firewall
- Monitor VXLAN
- Monitoring ESXi Hosts
- Index
3 Set up port binding.
a Identify the VMkernel port of the dependent hardware iSCSI adapter.
esxcli <conn_options> iscsi logicalnetworkportal list --adapter=<adapter_name>
b Connect the dependent hardware iSCSI initiator to the iSCSI VMkernel ports by running the
following command for each port.
esxcli <conn_options> iscsi networkportal add --nic=<bound_vmknic> --
adapter=<iscsi_adapter>
c Verify that the ports were added to the dependent hardware iSCSI initiator.
esxcli <conn_options> iscsi physicalnetworkportal list --adapter=<adapter_name>
4 Add a dynamic discovery address or a static discovery address.
n
With dynamic discovery, all storage targets associated with a host name or IP address are
discovered. You can run the following command.
esxcli <conn_options> iscsi adapter discovery sendtarget add --address=<ip/dns[:port]> --
adapter=<adapter_name>
n
With static discovery, you must specify the host name or IP address and the iSCSI name of the
storage target. You can run the following command.
esxcli <conn_options> iscsi adapter discovery statictarget add --address=<ip/dns[:port]>
--adapter=<adapter_name> --name=<target_name>
When you later remove a discovery address, it might still be displayed as the parent of a static target.
You can add the discovery address and rescan to display the correct parent for the static targets.
5 (Optional) Set the authentication information for CHAP.
You can set per-target CHAP for static targets, per-adapter CHAP, or apply the command to the
discovery address.
Option Command
Adapter-level CHAP
esxcli iscsi adapter auth chap set --direction=uni --
chap_username=<name> --chap_password=<pwd> --
level=[prohibited, discouraged, preferred, required] --
secret=<string> --adapter=<vmhba>
Discovery-level CHAP
esxcli iscsi adapter discovery sendtarget auth chap set --
direction=uni --chap_username=<name> --chap_password=<pwd>
--level=[prohibited, discouraged, preferred, required] --
secret=<string> --adapter=<vmhba> --
address<sendtarget_address>
Target-level CHAP
esxcli iscsi adapter target portal auth chap set --
direction=uni --chap_username=<name> --chap_password=<pwd>
--level=[prohibited, discouraged, preferred, required] --
secret=<string> --adapter=<vmhba> --name<iscsi_iqn_name>
The following example sets adapter-level CHAP.
esxcli <conn_options> iscsi adapter auth chap set --direction=uni --chap_username=<name> --
chap_password=<pwd> --level=preferred --secret=uni_secret --adapter=vmhba33
Chapter 5 Managing iSCSI Storage
VMware, Inc. 81