6.0
Table Of Contents
- vSphere Command-Line Interface Concepts and Examples
- Contents
- About This Book
- vSphere CLI Command Overviews
- Introduction
- List of Available Host Management Commands
- Targets and Protocols for vCLI Host Management Commands
- Supported Platforms for vCLI Commands
- Commands with an esxcfg Prefix
- ESXCLI Overview
- Connection Options for vCLI Host Management Commands
- Connection Options for DCLI Commands
- vCLI Host Management Commands and Lockdown Mode
- Managing Hosts
- Managing Files
- Managing Storage
- Introduction to Storage
- Examining LUNs
- Detaching Devices and Removing a LUN
- Working with Permanent Device Loss
- Managing Paths
- Managing Path Policies
- Scheduling Queues for Virtual Machine I/O
- Managing NFS/NAS Datastores
- Monitoring and Managing SAN Storage
- Monitoring and Managing Virtual SAN Storage
- Monitoring vSphere Flash Read Cache
- Monitoring and Managing Virtual Volumes
- Migrating Virtual Machines with svmotion
- Configuring FCoE Adapters
- Scanning Storage Adapters
- Retrieving SMART Information
- Managing iSCSI Storage
- iSCSI Storage Overview
- Protecting an iSCSI SAN
- Command Syntax for esxcli iscsi and vicfg-iscsi
- iSCSI Storage Setup with ESXCLI
- iSCSI Storage Setup with vicfg-iscsi
- Listing and Setting iSCSI Options
- Listing and Setting iSCSI Parameters
- Enabling iSCSI Authentication
- Setting Up Ports for iSCSI Multipathing
- Managing iSCSI Sessions
- Managing Third-Party Storage Arrays
- Managing NMP with esxcli storage nmp
- Path Claiming with esxcli storage core claiming
- Managing Claim Rules
- Managing Users
- Managing Virtual Machines
- vmware-cmd Overview
- Listing and Registering Virtual Machines
- Retrieving Virtual Machine Attributes
- Managing Virtual Machine Snapshots with vmware-cmd
- Powering Virtual Machines On and Off
- Connecting and Disconnecting Virtual Devices
- Working with the AnswerVM API
- Forcibly Stopping Virtual Machines with EXCLI
- Managing vSphere Networking
- Introduction to vSphere Networking
- Retrieving Basic Networking Information
- Network Troubleshooting
- Setting Up vSphere Networking with vSphere Standard Switches
- Setting Up Virtual Switches and Associating a Switch with a Network Interface
- Retrieving Information About Virtual Switches
- Adding and Deleting Virtual Switches
- Checking, Adding, and Removing Port Groups
- Managing Uplinks and Port Groups
- Setting the Port Group VLAN ID
- Managing Uplink Adapters
- Adding and Modifying VMkernel Network Interfaces
- Setting Up vSphere Networking with vSphere Distributed Switch
- Managing Standard Networking Services in the vSphere Environment
- Setting the DNS Configuration
- Adding and Starting an NTP Server
- Managing the IP Gateway
- Setting Up IPsec
- Managing the ESXi Firewall
- Monitoring VXLAN
- Monitoring ESXi Hosts
- Index
VMware, Inc. 127
Chapter 9 Managing vSphere Networking
2 ChangetheIPaddressasneeded.
vicfg-vmknic <conn_options> --ip <address> VMSF-VMK-363
ForIPv4,chooseoneofthefollowingformats:
<X.X.X.X>–StaticIPv4address.
DHCP–UseIPv4DHCP.
TheVMkernelsupportsDHCPonlyforESXi4.0andlater.
3 (Optional)EnablevMotion.
Bydefault,vMotionisdisabled.
vicfg-vmknic <conn_options> --enable-vmotion VMSF-VMK-363
Youcanlateruse--disable-vmotiontodisablevMotionforthisVMkernelnetworkinterface.
4ListinformationaboutallVMkernelnetworkinterfacesonthesystem.
vicfg-vmknic <conn_options> --list
Thecommanddisplaysthenetworkinformation,portgroup,MTU,andcurrentstateforeachvirtual
networkadapterinthesystem.
To add and configure an IPv6 VMkernel Network Interface with vicfg-vmknic
1Runvicfg-vmknic --addtoaddaVMkernelnetworkinterface.
YoumustspecifytheIPaddressbyusing--ip,thenetmask,andtheportgroupname.Forthefollowing
examples,assumethat
VMSF‐VMK‐363isaportgrouptowhichyouwanttoaddaVMkernelnetwork
interface.
YoucanspecifytheMTUsettingwhenyouaddaVMkernelnetworkinterface.Youcannotchangethat
settingatalatertime.
Whenthecommandcompletessuccessfully,thenewlyaddedVMkernelnetworkinterfaceis
enabled.
2EnableIPv6.
vicfg-vmknic <conn_options> --enable-ipv6 true VMSF-VMK-363
3 SupplyanIPv6address.
vicfg-vmknic <conn_options> --ip <ip_address> VMSF-VMK-363
ForIPv6,theIPaddresscanhaveoneofthefollowingformats:
<X:X:X::/X>–StaticIPv6address
DHCPV6–UseDHCPIPv6address.TheVMkernelsupportsDHCPonlyforESX/ESXi4.0andlater.
AUTOCONF–UsetheIPv6addressadvertisedbytherouter.IfyoucreateaVMkernelnetworkinterface
withAUTOCONF,anaddressisassignedimmediately.IfyouaddAUTOCONFtoanexisting
vmknic,theaddressisaddedwhentheroutersendsthenextrouteradvert.
4 (Optional)EnablevMotion.
Bydefault,vMotionis
disabled.
vicfg-vmknic <conn_options> --enable-vmotion VMSF-VMK-363
Youcanlateruse--disable-vmotiontodisablevMotionagain.
5ListinformationaboutallVMkernelnetworkinterfacesonthesystem.
vicfg-vmknic <conn_options> --list
Thelistcontainsthenetworkinformation,portgroup,MTU,andcurrentstateforeachvirtualnetwork
adapterinthesystem.
6YoucanlaterremovetheIPv6addressanddisableIPv6.