5.1
Table Of Contents
- VMware vCenter Converter Standalone User's Guide
- Contents
- About This Book
- Introduction to VMware vCenter Converter Standalone
- System Requirements
- Supported Operating Systems
- Supported Firmware Interfaces
- Supported Source Types
- Supported Destination Types
- Supported Source Disk Types
- Supported Destination Disk Types
- Support for IPv6 in Converter Standalone
- Installation Space Requirements
- Screen Resolution Requirements
- Configuring Permissions for vCenter Users
- TCP/IP and UDP Port Requirements for Conversion
- Requirements for Remote Hot Cloning of Windows Operating Systems
- Conversion Limitations
- Installing and Uninstalling Converter Standalone
- Perform a Local Installation on Windows
- Perform a Client-Server Installation in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Modify Converter Standalone in Windows
- Repair Converter Standalone in Windows
- Uninstall Converter Standalone in Windows
- Connect to a Remote Converter Standalone Server
- Convert a Physical or Virtual Machine
- Start the Wizard for a Conversion
- Select a Source Machine to Convert
- Select a Powered On Windows Machine to Convert
- Select a Powered On Linux Machine to Convert
- Select an ESX/ESXi or vCenter Server Virtual Machine to Convert
- Select a VMware Hosted Virtual Machine to Convert
- Select a Backup Image or a Third-Party Virtual Machine to Convert
- Select a Hyper-V Server Virtual Machine to Convert
- Select a Destination for the New Virtual Machine
- Configure the Hardware of the Destination Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Resize a Volume
- Change a Volume Cluster Size
- Exclude a Source Volume from the Conversion Process
- Move a Volume to a Different Virtual Disk
- Select the Destination Datastore for a Source Volume
- Add a Virtual Disk
- Set Up a Virtual Disk as a Logical-Volume Group Container
- Move a Disk to a Different Datastore
- Create an Expandable Disk on a Managed Destination
- Create an Expandable Disk on a Hosted Destination
- Exclude a Source Disk from the Conversion Process
- Copy All Disks to the Destination
- Create an Optimized Partition Layout
- Create a Linked Clone
- Edit the Number of Processor Sockets and Cores
- Allocate Memory for the Destination Virtual Machine
- Select a Disk Controller for the Destination Virtual Machine
- Configure the Network Settings of the Destination Virtual Machine
- Configure the Network for the Helper Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Configure the Software on the Destination Virtual Machine
- Configure the Conversion Job
- Set the Startup Mode for Destination Services
- Stop Services Running on the Source Machine
- Synchronize the Destination Machine with Changes Made to the Source Machine
- Power Off the Source Machine After Conversion
- Power On the Destination Virtual Machine After Conversion
- Limit the Amount of Resources Used by the Conversion Job
- Uninstall Converter Standalone Agent from the Source Machine
- Review the Summary and Submit the Conversion Job
- Configure Virtual Machines
- Save Sysprep Files
- Start the Configuration Wizard
- Select a Source Machine to Configure
- Select the Options to Configure
- Review and Submit the Configuration Job
- Manage Conversion and Configuration Jobs and Tasks
- Index
2 In the list of installed programs, locate and click VMware vCenter Converter Standalone Agent.
3 Click Remove.
4 In the confirmation dialog box, click Yes.
Windows installer uninstalls the Converter Standalone agent from the source machine.
Review the Summary and Submit the Conversion Job
On the Summary page, you can view a summary of the conversion job before you add it to the job list.
The summary includes information about the source machine, the destination virtual machine, and destination
customization settings (if any). Converter Standalone performs job validation at this stage.
Prerequisites
You must complete all steps in the Conversion wizard to access the Summary page.
Procedure
1 Review the summary of the job.
2 Click Finish to submit the job.
Converter Standalone validates the job parameters. This might take several minutes. If the validation succeeds,
the conversion job appears in the Job View list in the main application window. You can find information about
the tasks of the job in the Task View. If the validation fails, you must click Back and correct the invalid
parameters as prompted.
VMware vCenter Converter Standalone User's Guide
74 VMware, Inc.