5.1
Table Of Contents
- VMware vCenter Converter Standalone User's Guide
- Contents
- About This Book
- Introduction to VMware vCenter Converter Standalone
- System Requirements
- Supported Operating Systems
- Supported Firmware Interfaces
- Supported Source Types
- Supported Destination Types
- Supported Source Disk Types
- Supported Destination Disk Types
- Support for IPv6 in Converter Standalone
- Installation Space Requirements
- Screen Resolution Requirements
- Configuring Permissions for vCenter Users
- TCP/IP and UDP Port Requirements for Conversion
- Requirements for Remote Hot Cloning of Windows Operating Systems
- Conversion Limitations
- Installing and Uninstalling Converter Standalone
- Perform a Local Installation on Windows
- Perform a Client-Server Installation in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Modify Converter Standalone in Windows
- Repair Converter Standalone in Windows
- Uninstall Converter Standalone in Windows
- Connect to a Remote Converter Standalone Server
- Convert a Physical or Virtual Machine
- Start the Wizard for a Conversion
- Select a Source Machine to Convert
- Select a Powered On Windows Machine to Convert
- Select a Powered On Linux Machine to Convert
- Select an ESX/ESXi or vCenter Server Virtual Machine to Convert
- Select a VMware Hosted Virtual Machine to Convert
- Select a Backup Image or a Third-Party Virtual Machine to Convert
- Select a Hyper-V Server Virtual Machine to Convert
- Select a Destination for the New Virtual Machine
- Configure the Hardware of the Destination Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Resize a Volume
- Change a Volume Cluster Size
- Exclude a Source Volume from the Conversion Process
- Move a Volume to a Different Virtual Disk
- Select the Destination Datastore for a Source Volume
- Add a Virtual Disk
- Set Up a Virtual Disk as a Logical-Volume Group Container
- Move a Disk to a Different Datastore
- Create an Expandable Disk on a Managed Destination
- Create an Expandable Disk on a Hosted Destination
- Exclude a Source Disk from the Conversion Process
- Copy All Disks to the Destination
- Create an Optimized Partition Layout
- Create a Linked Clone
- Edit the Number of Processor Sockets and Cores
- Allocate Memory for the Destination Virtual Machine
- Select a Disk Controller for the Destination Virtual Machine
- Configure the Network Settings of the Destination Virtual Machine
- Configure the Network for the Helper Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Configure the Software on the Destination Virtual Machine
- Configure the Conversion Job
- Set the Startup Mode for Destination Services
- Stop Services Running on the Source Machine
- Synchronize the Destination Machine with Changes Made to the Source Machine
- Power Off the Source Machine After Conversion
- Power On the Destination Virtual Machine After Conversion
- Limit the Amount of Resources Used by the Conversion Job
- Uninstall Converter Standalone Agent from the Source Machine
- Review the Summary and Submit the Conversion Job
- Configure Virtual Machines
- Save Sysprep Files
- Start the Configuration Wizard
- Select a Source Machine to Configure
- Select the Options to Configure
- Review and Submit the Configuration Job
- Manage Conversion and Configuration Jobs and Tasks
- Index
Procedure
1 If you are converting a powered on source machine, click the Destination services tab.
If the source machine is powered off, the Services pane displays no tabs. You can modify only the starting
mode of destination services.
2 On the services list, select the startup mode for each service.
Option Description
Automatic
The service starts automatically after the destination machine is powered on.
Manual
The service does not start after the destination machine is powered on, but
you can start it manually.
Disabled
The service is disabled and does not start after the destination machine is
powered on.
3 Save your settings.
Option Description
Select another option from the
options list
Saves your settings and displays the pane for the selected option.
Click Next
Saves your settings and displays the next page of the Conversion wizard.
n
The Customizations page is displayed if you select Customize guest
preferences for the virtual machine in the Advanced options pane.
n
The Summary page is displayed if you do not select Customize guest
preferences for the virtual machine in the Advanced options pane.
Stop Services Running on the Source Machine
You can make sure that you do not lose data from services running on the source machine. You can select the
services that you want to stop before Converter Standalone synchronizes the data between the source and
destination machine. As a result, the services do not generate data while source and destination machines are
synchronized.
You can stop services on the source only when you convert a powered on Windows machine.
Prerequisites
On the Options page of the Conversion wizard, click Services in the options list.
Procedure
1 Click the Source services tab.
2 To stop a service on the source machine before synchronization, highlight a service and select the Stop
check box to the right.
3 Save your settings.
Option Description
Select another option from the
options list
Saves your settings and displays the pane for the selected option.
Click Next
Saves your settings and displays the next page of the Conversion wizard.
n
The Customizations page is displayed if you select Customize guest
preferences for the virtual machine in the Advanced options pane.
n
The Summary page is displayed if you do not select Customize guest
preferences for the virtual machine in the Advanced options pane.
VMware vCenter Converter Standalone User's Guide
70 VMware, Inc.