5.0
Table Of Contents
- VMware vCenter Converter Standalone User's Guide
- Contents
- About This Book
- Introduction to VMware vCenter Converter Standalone
- System Requirements
- Supported Operating Systems
- Installation Space Requirements
- Screen Resolution Requirements
- Supported Source Types
- Supported Destination Types
- Restoring VCB Images in Converter Standalone
- Configuring Permissions for vCenter Users
- Support for IPv6 in Converter Standalone
- TCP/IP and UDP Port Requirements for Conversion
- Requirements for Remote Hot Cloning of Windows Operating Systems
- Installing and Uninstalling Converter Standalone
- Perform a Local Installation on Windows
- Perform a Client-Server Installation in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Modify Converter Standalone in Windows
- Repair Converter Standalone in Windows
- Uninstall Converter Standalone in Windows
- Connect to a Remote Converter Standalone Server
- Convert a Physical or Virtual Machine
- Start the Wizard for a Conversion
- Select a Source Machine to Convert
- Select a Powered-On Windows Machine to Convert
- Select a Powered-On Linux Machine to Convert
- Select an ESX/ESXi or vCenter Server Virtual Machine to Convert
- Select a VMware Hosted Virtual Machine to Convert
- Select a Backup Image or a Third-Party Virtual Machine to Convert
- Select a Hyper-V Server Virtual Machine to Convert
- Select a Destination for the New Virtual Machine
- Configure the Hardware of the Destination Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Resize a Volume
- Change a Volume Cluster Size
- Exclude a Source Volume from the Conversion Process
- Move a Volume to a Different Virtual Disk
- Select the Destination Datastore for a Source Volume
- Add a Virtual Disk
- Set Up a Virtual Disk as a Logical-Volume Group Container
- Move a Disk to a Different Datastore
- Create an Expandable Disk on a Managed Destination
- Create an Expandable Disk on a Hosted Destination
- Exclude a Source Disk from the Conversion Process
- Copy All Disks to the Destination
- Create an Optimized Partition Layout
- Create a Linked Clone
- Edit the Number of Processor Sockets and Cores
- Allocate Memory for the Destination Virtual Machine
- Specify a Disk Controller for the Destination Virtual Machine
- Configure the Network Settings of the Destination Virtual Machine
- Configure the Network for the Helper Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Configure the Software on the Destination Virtual Machine
- Configure the Conversion Job
- Set the Startup Mode for Destination Services
- Stop Services Running on the Source Machine
- Synchronize the Destination Machine with Changes Made to the Source Machine
- Power Off the Source Machine After Conversion
- Power On the Destination Virtual Machine After Conversion
- Limit the Amount of Resources Used by the Conversion Job
- Uninstall Converter Standalone Agent from the Source Machine
- Review the Summary and Submit the Conversion Job
- Configure Virtual Machines
- Save Sysprep Files
- Start the Configuration Wizard
- Select a Source Machine to Configure
- Select the Options to Configure
- Review and Submit the Configuration Job
- Manage Conversion and Configuration Jobs and Tasks
- Index
Procedure
1 Click the Other tab.
2 From the Disk controller drop-down menu, select a disk controller for the destination virtual disk.
Option Description
SCSI Bus Logic
Use SCSI virtual disks in the destination virtual machine.
IDE
Use IDE virtual disks in the destination virtual machine.
LSI Logic
Use LSI Logic SCSI virtual disks in the destination virtual machine.
LSI Logic SAS
Use LSI Logic SCSI (SAS) virtual disks in the destination virtual machine.
Auto select
Use the same types of disk controllers as those installed on the source
machine. If they are not supported on the destination virtual machine,
replace them with supported ones.
NOTE When converting Linux virtual machines on ESX and vCenter Server
earlier than 4.1, the system might not retrieve the full list of supported
controllers.
3 Save your settings.
Option Description
Select another option from the
options list
Saves your settings and displays the pane for the selected option.
Click Next
Saves your settings and displays the next page of the Conversion wizard.
n
The Customizations page is displayed if you select Customize guest
preferences for the virtual machine in the Advanced options pane.
n
The Summary page is displayed if you do not select Customize guest
preferences for the virtual machine in the Advanced options pane.
Configure the Network Settings of the Destination Virtual Machine
You can change the number of network adapters and select the network that the destination virtual machine
uses. You can also set network adapters to connect to the network when the destination virtual machine powers
on.
NOTE You cannot use IPv6 to customize the guest operating systems of virtual machines.
Prerequisites
On the Options page of the Conversion wizard, select Networks from the options list.
Procedure
1 From the Network adapters to connect drop-down menu, select the number of network adapters to be
used by the destination virtual machine.
2 Use the Network drop-down menu to select the network that the adapter connects to.
3 To connect an adapter when you power on the destination virtual machine, select the Connect at power-
on check box.
VMware vCenter Converter Standalone User's Guide
60 VMware, Inc.