4.3
Table Of Contents
- VMware vCenter Converter Standalone User's Guide
- Contents
- Updated Information
- About This Book
- Introduction to VMware vCenter Converter Standalone
- System Requirements
- Supported Operating Systems
- Installation Space Requirements
- Supported Source Types
- Supported Destination Types
- Configuring Permissions for VirtualCenter Users
- Support for IPv6 in Converter Standalone
- TCP/IP and UDP Port Requirements for Conversion
- Requirements for Remote Hot Cloning of Windows Operating Systems
- Installing and Uninstalling Converter Standalone
- Perform a Local Installation on Windows
- Perform a Client-Server Installation in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Modify Converter Standalone in Windows
- Repair Converter Standalone in Windows
- Uninstall Converter Standalone in Windows
- Connect to a Remote Converter Standalone Server
- Convert a Physical or Virtual Machine
- Start the Wizard for a Conversion
- Select a Source Machine to Convert
- Select a Powered-On Windows Machine to Convert
- Select a Powered-On Linux Machine to Convert
- Select an ESX/ESXi or vCenter Server Virtual Machine to Convert
- Select a VMware Hosted Virtual Machine to Convert
- Select a Backup Image or a Third-Party Virtual Machine to Convert
- Select a Hyper-V Server Virtual Machine to Convert
- Select a Destination for the New Virtual Machine
- Configure the Hardware of the Destination Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Resize a Volume
- Exclude a Source Volume from the Conversion Process
- Move a Volume to a Different Virtual Disk
- Select the Destination Datastore for a Source Volume
- Add a Virtual Disk
- Move a Disk to a Different Datastore
- Create an Expandable Disk on a Managed Destination
- Create an Expandable Disk on a Hosted Destination
- Exclude a Source Disk from the Conversion Task
- Copy All Disks to the Destination
- Create a Linked Clone
- Edit the Number of Processors
- Allocate Memory for the Destination Virtual Machine
- Specify a Disk Controller for the Destination Virtual Machine
- Configure the Network Settings of the Destination Virtual Machine
- Configure the Network for the Helper Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Configure the Software on the Destination Virtual Machine
- Configure the Conversion Task
- Set the Startup Mode for Destination Services
- Stop Services Running on the Source Machine
- Synchronize the Destination Machine with Changes Made to the Source Machine
- Power Off the Source Machine After Conversion
- Power On the Destination Virtual Machine After Conversion
- Limit the Amount of Resources Used by the Conversion Task
- Uninstall Converter Standalone Agent from the Source Machine
- Review the Summary and Submit the Conversion Task
- Configure Virtual Machines
- Save Sysprep Files
- Start the Configuration Wizard
- Select a Source Machine to Configure
- Select the Options to Configure
- Review and Submit the Configuration Task
- Managing Conversion and Configuration Tasks
- Index
7 (Optional) If you installed the Converter Standalone client, deselect Run Converter Standalone Client
now to complete the installation without starting the application at this time.
8 On the Installation Completed page, click Finish.
A prompt might ask you to restart your system.
The selected Converter Standalone components are installed on the local machine and are ready for use.
What to do next
You can use Converter Standalone to convert physical or virtual machine sources to virtual machine
destinations.
Repair Converter Standalone in Windows
You can repair the Converter Standalone installation to check for and reinstall the Converter Standalone client
or Converter Standalone agent.
Prerequisites
Make sure that you have Administrator privileges.
Close the Converter Standalone application before you start the installer wizard.
Procedure
1 To start the Converter Standalone installer, do one of the following:
n
Go to the folder that contains the installer file and double-click the VMware-converter-4.x.x-
<xxxxx>.exe file, where <xxxxx> is the number of the build. Check the number of the build to see if it
matches the build you installed.
n
Select Add or Remove Programs from the Control Panel, select Converter Standalone from the list,
and click Change.
2 On the Welcome page of the installer wizard, click Next.
3 On the Program Maintenance page, select Repair and click Next.
4 On the Ready to Repair page, click Install.
5 On the Installation Completed page, click Finish.
A prompt might ask you to restart your system.
What to do next
You can use Converter Standalone to convert physical or virtual machine sources to virtual machine
destinations.
Uninstall Converter Standalone in Windows
You can uninstall Converter Standalone by using the Microsoft Windows Add or Remove Programs utility
from the Control Panel or by using the VMware vCenter Converter Standalone installer wizard.
Prerequisites
Make sure that you have Administrator privileges.
Close the Converter Standalone application before you start the installer wizard.
VMware vCenter Converter Standalone User's Guide
38 VMware, Inc.