4.3
Table Of Contents
- VMware vCenter Converter Standalone User's Guide
- Contents
- Updated Information
- About This Book
- Introduction to VMware vCenter Converter Standalone
- System Requirements
- Supported Operating Systems
- Installation Space Requirements
- Supported Source Types
- Supported Destination Types
- Configuring Permissions for VirtualCenter Users
- Support for IPv6 in Converter Standalone
- TCP/IP and UDP Port Requirements for Conversion
- Requirements for Remote Hot Cloning of Windows Operating Systems
- Installing and Uninstalling Converter Standalone
- Perform a Local Installation on Windows
- Perform a Client-Server Installation in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Modify Converter Standalone in Windows
- Repair Converter Standalone in Windows
- Uninstall Converter Standalone in Windows
- Connect to a Remote Converter Standalone Server
- Convert a Physical or Virtual Machine
- Start the Wizard for a Conversion
- Select a Source Machine to Convert
- Select a Powered-On Windows Machine to Convert
- Select a Powered-On Linux Machine to Convert
- Select an ESX/ESXi or vCenter Server Virtual Machine to Convert
- Select a VMware Hosted Virtual Machine to Convert
- Select a Backup Image or a Third-Party Virtual Machine to Convert
- Select a Hyper-V Server Virtual Machine to Convert
- Select a Destination for the New Virtual Machine
- Configure the Hardware of the Destination Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Resize a Volume
- Exclude a Source Volume from the Conversion Process
- Move a Volume to a Different Virtual Disk
- Select the Destination Datastore for a Source Volume
- Add a Virtual Disk
- Move a Disk to a Different Datastore
- Create an Expandable Disk on a Managed Destination
- Create an Expandable Disk on a Hosted Destination
- Exclude a Source Disk from the Conversion Task
- Copy All Disks to the Destination
- Create a Linked Clone
- Edit the Number of Processors
- Allocate Memory for the Destination Virtual Machine
- Specify a Disk Controller for the Destination Virtual Machine
- Configure the Network Settings of the Destination Virtual Machine
- Configure the Network for the Helper Virtual Machine
- Organize the Data to Copy on the Destination Machine
- Configure the Software on the Destination Virtual Machine
- Configure the Conversion Task
- Set the Startup Mode for Destination Services
- Stop Services Running on the Source Machine
- Synchronize the Destination Machine with Changes Made to the Source Machine
- Power Off the Source Machine After Conversion
- Power On the Destination Virtual Machine After Conversion
- Limit the Amount of Resources Used by the Conversion Task
- Uninstall Converter Standalone Agent from the Source Machine
- Review the Summary and Submit the Conversion Task
- Configure Virtual Machines
- Save Sysprep Files
- Start the Configuration Wizard
- Select a Source Machine to Configure
- Select the Options to Configure
- Review and Submit the Configuration Task
- Managing Conversion and Configuration Tasks
- Index
3 Converter Standalone completes the conversion process.
The agent installs the required drivers to allow the operating system to boot in a virtual machine and
personalizes the virtual machine (changes the IP information, for example).
agent
vCenter Converter Standalone running
on Windows machine
powered-on
physical machine
ESX/ESXi
source
destination
network
VM
source
volumes
snapshot
reconfiguration
customization (optional)
4 Optionally, Converter Standalone uninstalls the agent from the source machine.
The virtual machine is ready to run on the destination server.
Remote Hot Cloning of Physical Machine Sources That Are Running Linux
The conversion process of physical machines that are running Linux operating systems differs from that of
Windows machines.
In Windows conversions, the Converter Standalone agent is installed on the source machine and the source
information is pushed to the destination.
In Linux conversions, no agent is deployed on the source machine. Instead, a helper virtual machine is created
and deployed on the destination ESX/ESXi host. The source data is then copied from the source Linux machine
to the helper virtual machine. After the conversion is complete, the helper virtual machine shuts down to
become the destination virtual machine the next time you power it on.
Converter Standalone supports conversion of Linux sources only to managed destinations.
VMware vCenter Converter Standalone User's Guide
14 VMware, Inc.