4.0.1
Table Of Contents
- User's Guide
- Contents
- Updated Information
- About This Book
- Introduction
- Migration with Converter Standalone
- Converter Standalone Components
- Converter Standalone Features
- System Requirements
- Supported Operating Systems
- Installation Space Requirements
- Supported Source Types
- Supported Destination Types
- Restoring VCB Images in Converter Standalone
- How Conversion Affects the Source Settings When They Are Applied to the Destination
- Changes That Conversion Causes to Virtual Hardware
- TCP/IP Port Requirements for Conversion
- Common Requirements for Remote Hot Cloning of Windows Operating Systems
- Installing and Uninstalling VMware vCenter Converter Standalone
- Install Converter Standalone in Windows
- Uninstall, Modify, or Repair Converter Standalone in Windows
- Perform a Command-Line Installation in Windows
- Command-Line Options for Windows Installation
- Perform a Local Installation in Linux
- Perform a Client-Server Installation in Linux
- Uninstall Converter Standalone in Linux
- Modify or Repair Converter Standalone in Linux
- Connect to a Remote Converter Standalone Server
- Converting Machines
- Convert a Machine
- Start the Wizard for a Conversion
- Select a Source to Convert
- Select a Destination for the New Virtual Machine
- View Setup Options for a New Virtual Machine
- Select the Destination Folder
- Organizing the Data to Copy to the Destination Machine
- Distribute Disks over Several Datastores
- Distribute Volumes over Several Datastores
- Create or Delete a Target Disk
- Move a Source Volume to a Target Virtual Disk
- Modify the Settings in the Source Volumes List
- Change the Target Datastore for a Destination Virtual Disk
- Create a Thin Provisioned Disk
- Create a Linked Clone
- Change Device Settings on the New Virtual Machine
- Change Network Connections on the Destination
- Control the Status of Windows Services During Conversion
- Advanced Customization Options
- Synchronize the Source with the Destination Machine
- Adjust the Post-Conversion Power State
- Install VMware Tools
- Customize the Guest Operating System
- Edit the Destination Computer Information
- Enter the Windows License Information
- Set the Time Zone
- Set Up the Network Adapters
- Assign a Workgroup or Domain Details
- Remove System Restore Checkpoints
- Set Up the Network for the Helper Virtual Machine
- Customize a VMware Infrastructure Virtual Machine
- Customize a Standalone or Workstation Virtual Machine
- Customize a Virtual Appliance
- Configure the Product Properties of an Exported Virtual Appliance
- View the Summary of a Conversion Task
- Convert a Machine
- Configuring VMware Virtual Machines
- Configure a Virtual Machine
- Save Sysprep Files
- Select a Source to Configure
- Select the Options to Configure
- Customize a Virtual Machine’s Guest Operating System
- Edit the Computer Information of a Configured Virtual Machine
- Enter the Windows License Information of a Configured Virtual Machine
- Set the Time Zone of a Configured Virtual Machine
- Set Up the Network Adapters of a Configured Virtual Machine
- Assign a Workgroup or Domain Details of a Configured Virtual Machine
- View the Summary of a Configuration Task
- Configure a Virtual Machine
- Managing Conversion and Configuration Tasks
- Glossary
- Index
Conversion Limitations for Third-Party Virtual Machines or System Images
Converter Standalone can convert third-party virtual machines, system images, and ShadowProtect and
BackupExec System Recovery images. These conversions have some limitations.
Third-party virtual machines and system images have the following limitations:
n
Virtual machines from Macintosh versions of Virtual PC are not supported.
n
The operating system on the source Virtual PC or Virtual Server virtual machine must be a Windows guest
operating system supported by the intended VMware platform (for example, Workstation 5 or 6.0.x). For
a list of supported operating systems, see the Guest Operating System Installation Guide.
Converter Standalone supports Virtual PC and Virtual Server virtual machines with most Windows
operating systems earlier than Windows NT 4.0 and with non-Windows operating systems (for example,
Linux and DOS) only for cloning. Converter Standalone does not support configuring for these systems.
ShadowProtect and Backup Exec System Recovery have the following limitations:
n
Dynamic disks are not supported.
n
All images for the backup of a machine must be in a single folder with no other images placed there.
n
For volume-based cloning, all volumes in the disk up to the active and system volumes must be backed
up. For example, if a disk has four partitions, 1 through 4, with partition 2 as the active volume and partition
3 as the system volume, the backup must include partitions 1 through 3.
n
For incremental images, up to 16 incremental backups are supported.
n
Images of systems with logical drives are not supported if the logical drive is also a system or active volume
(ShadowProtect only).
Conversion Limitations for Virtual Appliances
Some limitations exist when you convert virtual appliances.
The following scenarios are not supported:
n
Converting local and remote physical machines to virtual appliances
n
Selecting a subset of the volumes or resizing the volumes. You must select all volumes for an import and
maintain the size of all of the volumes on the target machine.
n
Converting from OVF to OVF. That is, when both source and destination are virtual appliances.
n
Converting third-party backup images or virtual machine images to a virtual appliance.
n
Converting Windows 2000 virtual machines with scsiport.sys driver version 5.0.2195.7017 to a virtual
appliance.
n
Converting Windows NT 4 SMP virtual machines to a virtual appliance.
Although Converter Standalone does not support the preceding scenarios, in each case you can use Converter
Standalone to first convert the source machine to a VMware virtual machine and then convert that machine to
a virtual appliance.
Supported Destination Types
Converter Standalone can create virtual machines compatible with VMware hosted and managed products.
Converter Standalone can also create virtual appliances for Internet distribution.
Table 2-6 shows the destinations that Converter Standalone supports.
Chapter 2 System Requirements
VMware, Inc. 23