User Manual
Table Of Contents
- VIZIO 2.1 Sound Bar User Manual
- Accessibility ,
- IMPORTANT SAFETY INSTRUCTIONS ,
- TABLE OF CONTENTS ,
- Package Contents ,
- Controls & Connections ,
- First-time Setup ,
- Back of Subwoofer
- 1 Choose the best possible connection cable type and connect it to your TV.*
- 2 Connect the power cable to the sound bar AC IN as shown.
- 3 Connect the power cable to the subwoofer.
- 4 Plug the power cable into a power outlet.
- 5 The subwoofer should automatically power on and link to the sound bar when plugged in. The LED will glow to solid to confirm.
- 6 Remove the battery cover by gently sliding it away from the remote.
- 7 Insert the included batteries and gently slide the battery cover back into place.
- 8 After turning on both your TV and sound bar, it will automatically begin searching for an active input.* The LED indicator on the front of the sound bar will begin cycling in different colors through inputs until an audio source is detected. Double Asterisk
- Using the Remote ,
- Proper Placement ,
- Mode & Level Settings ,
- Using Button Combinations ,
- Programming the Sound Bar ,
- Bluetooth Pairing ,
- Using Bluetooth Mode ,
- Connecting to a Voice Assistant ,
- Advanced Setup ,
- Connecting a Subwoofer ,
- 1 First confirm that the power LED is illuminated. Press and hold the ON/OFF button on the back of the subwoofer for 5 seconds. The LED on the back of the subwoofer will begin to blink.
- 2 Press and hold the Power button on the top of the sound bar for 5 seconds. The LED indicators on the front will flash 3 times. The subwoofer is now linked with the sound bar.
- Product Registration and Support ,
- Help & Troubleshooting ,
- Limited Warranty ,
- UNITED STATES
- How Long This Warranty Lasts
- What This Warranty Covers
- How to Get Service
- Your Obligations Before Service
- VIZIO’s Responsibilities
- Types of Service
- What This Warranty Does Not Cover
- What to Do If You Are Not Satisfied With Service
- Binding Arbitration Agreement; Class Action Waiver (U.S. Residents Only)
- Opt-Out Instructions
- Exclusions and Limitations
- How the Law Applies
- General
- Changes to Warranty
- Legal & Compliance ,
- Specifcations ,
Mode & Level Settings
Function LED Behavior Description
Bass Level
Two center LEDs
indicate bass level 0.
Press the BASS button and use the Next/Previous buttons to increase/decrease the bass
level. The LED indicators will move to the top with increasing level and to the bottom with
decreasing level.
Subwoofer Level
Two center LEDs
indicate subwoofer
level 0.
Press the SUB button then press the Next/Previous button to increase/decrease the
subwoofer level. The LED indicators will move to the top with increasing levels and to the
bottom with decreasing levels. When set to the minimum level, the subwoofer will be muted.
Treble Level
Two center LEDs
indicate treble level 0.
Press the TREB button and use the Next/Previous buttons to increase/decrease the
treble level. The LED indicators will move to the top with increasing level and to the bottom
with decreasing level.
Auto VA
BT/AUX VA On
BT/AUX VA O
Press and Hold the INPUT button on the remote for 10 seconds to enable/disable AUX VA.
—or—
Press and Hold the Bluetooth(
) button on the remote for 10 seconds to enable/disable
Voice Assistant Bluetooth (BT). Refer to Connecting to a Voice Assistant on page 18 for
more information.
Dolby Audio
Detected
Dolby Audio audio
format is detected.
Dolby Audio is only available on the Digital Optical Audio In input. When a Dolby Audio
signal is detected, the Dolby Audio indicator LED will light up for 3 seconds before
fading away.
ENG - 13