FPO USER MANUAL Models E43-F1, E50-F2, E55-F0, E55-F1, E65-F0,D50-F1, E65-F1,D55-F2, E70-F3,D60-F3, E75-F1, D65-F1, E75-F2,and andD70-F3 E80-F3 Models: D43-F1,
Safety & Certification THANK YOU FOR CHOOSING VIZIO IMPORTANT SAFETY INSTRUCTIONS • And congratulations on your new VIZIO TV. Your TV is designed and manufactured to operate within defined design limits. Misuse may result in electric shock or fire. To prevent your TV from being damaged, the following instructions should be observed for the installation, use, and maintenance of your TV. Read the following safety instructions before operating your TV.
cord. • The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-isolated, dangerous voltage within the inside of your TV that may be of sufficient magnitude to constitute a risk of electric shock to persons. • Do not overload power strips and extension cords. Overloading can result in fire or electric shock. • The wall socket should be installed near your TV and easily accessible.
TELEVISION ANTENNA CONNECTION PROTECTION If an outside antenna/satellite dish or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, the symbol, DTS and the Symbol together, and DTS Studio Sound II are registered trademarks and/or trademarks of DTS, Inc. in the United States and/or other countries. ©DTS, Inc. All Rights Reserved.
Table Of Contents Getting to Know Your TV..............................................7 Setting the Timer..............................................................................24 Using the Reset & Admin Menu..........................................................34 Front Panel...........................................................................................7 Setting the Auto Power Off Feature................................................
Getting to Know Your TV 1 FRONT PANEL FPO REMOTE SENSOR & POWER INDICATOR When using the remote, aim it directly at this sensor. The power indicator flashes on when the TV turns on, then goes out after several seconds. To keep the power indicator on as long as the TV is on, see Turning the Power Indicator On or Off.
1 USB - Connect a USB thumb drive to play photos, music, or videos. REAR PANEL Component/Composite - Connect a component/composite. HDMI - Connect an HDMI device. Optical Audio Out - Connect to an optical/SPDIF audio device, such as home audio receiver. HDMI - Connect an HDMI device. Audio Out - Connect to an RCA device, such as sound bar. Coaxial - Connect to a coaxial cable from cable, satellite, or antenna. Ethernet - Connect an Ethernet cable to modem/ router. Power - Press to turn on the TV.
1 WALL-MOUNTING THE TV To mount your TV on a wall, you will need a wall mount. Consult the information on this page to find the appropriate mount for your TV. Be sure the mount you choose is capable of supporting the weight of the TV. After you have determined that you have the correct mount for your TV, you can begin the installation. To install your TV on a wall: 1. Disconnect any cables connected to your TV. 2. Place the TV face-down on a clean, flat, stable surface.
1 Replacing the Batteries USING THE REMOTE 2 1 3 4 5 6 7 8 9 11 10 12 14 13 15 16 1. Find the notch on the back of the remote. Insert a coin and pry open the back cover. 2. Insert two batteries into the remote control. Make sure that the (+) and (-) symbols on the batteries match the (+) and (-) symbols inside the battery compartment. 3. Replace the battery cover. In many places batteries cannot be thrown away or discarded with household waste.
Completing The First-Time Setup 2 The first time you turn on the TV, the on-screen instructions will guide you through each of the steps necessary to get your TV ready for use: Before you begin the first-time setup: • Your Television should be installed and the power cord should be connected to an electrical outlet. • If you have a wireless network, have the network password ready. • If you are connecting to your network with an Ethernet cable, connect it to the Ethernet port on the Television. 1.
Using the On-Screen Menu Your TV features an easy-to-use on-screen menu. To open the on-screen menu, press the Menu button on the remote.
3 CHANGING THE SCREEN ASPECT RATIO Tip: The aspect ratio cannot be changed for Ultra HD content or HDR content. The TV can display images in four different modes: Normal, Panoramic, Wide, and Zoom. Each mode displays the picture differently. Some programs have black bars on the top or sides of the picture so that the picture keeps its original shape. Examples include wide-screen movies and older television programs. To change the screen aspect ratio: 1. Press the Wide button on the remote. 2.
3 ADJUSTING THE PICTURE SETTINGS Your TV can be adjusted to suit your preferences and viewing conditions. If you’ve made changes to the settings for a picture mode, an asterisk appears after its name (see Saving a Custom Picture Mode). 3. Use the Arrow buttons on the remote to highlight Picture Mode, then use the Left/Right Arrow buttons to change the picture mode: • • To adjust the picture settings: 1. Press the Menu button on the remote. The on-screen menu is displayed. 2.
3 Adjusting More Picture Settings Adjusting the Color Temperature To adjust more picture settings: Adjusting the color temperature changes the white balance of the picture. 1. From the PICTURE menu, use the Arrow buttons to highlight More Picture, and then press OK. 2. Use the Arrow buttons to highlight the setting you wish to adjust, then press the Left/ Right Arrow buttons to change the setting: • Color Temperature See Adjusting the Color Temperature.
3 Adjusting the Picture Mode Edit Settings Saving a Custom Picture Mode Locking/Unlocking a Custom Picture Mode Picture Mode Edit Settings allow you to make precise adjustments to the picture and to create picture modes to save groups of picture settings. Custom picture modes allow you to save a group of custom settings for various viewing conditions and video sources. • Changes made while on any preset picture mode will add an asterisk on the top right corner of the preset mode.
3 Deleting a Custom Picture Mode Resetting a Picture Mode Custom picture modes that are no longer needed can be deleted. A preset picture mode that has been edited can be restored to the factory default settings. Inputs assigned to a deleted custom picture mode become assigned to the Calibrated picture mode. To delete a custom picture mode: 1. From the PICTURE MODE EDIT menu, use the Arrow buttons to highlight Delete Picture Mode, and then press OK. The DELETE PICTURE MODE window is displayed.
3 Adjusting the Color Tuner Settings The Color Tuner settings allow you to adjust the HSB color and 11 point white balance, turn color channels off for testing, and display color bar, flat, and ramp test patterns. The Color Tuner, 11 Point White Balance, and test patterns allow technicians to manually calibrate the TV. Calibration requires specialized training, an input with precisely set colors, and a specialized light meter. To adjust the HSB color settings: 1.
3 To show or hide the SMPTE Test Pattern: To show or hide the Flat Test Pattern: To show or hide the Ramp Test Pattern: 1. From the COLOR CALIBRATION menu, use the Arrow buttons to highlight Calibration Test, and then press the Left/ Right Arrow buttons until the SMPTE TEST PATTERN menu is displayed. 1. From the COLOR CALIBRATION menu, use the Arrow buttons to highlight Calibration Test, and then press the Left/Right Arrow buttons until the FLAT TEST PATTERN menu is displayed. 1.
3 To show or hide the Uniformity Analyzer Test Pattern: 1. From the COLOR CALIBRATION menu, use the Arrow buttons to highlight Calibration Tests, and then press the Left/Right Arrow buttons until the UNIFORMITY ANALYZER TEST PATTERN menu is displayed. Uniformity Analyzer Test Pattern Off 2. Use the Arrow buttons on the remote to highlight Off. Use the Left/Right Arrow buttons to highlight On to show the Uniformity Analyzer Test Pattern.
3 ADJUSTING THE AUDIO SETTINGS To adjust the audio settings: Audio 1. Press the Menu button on the remote. The on-screen menu is displayed. Speakers Back Auto Volume Control Display On Surround Sound On 2. Use the Arrow buttons on the remote to highlight Audio and press OK. The AUDIO menu is displayed. Volume Leveling Off Digital Audio Out Auto 3.
3 ADJUSTING THE NETWORK SETTINGS Your TV is Internet-ready, featuring both an Ethernet port and built-in high-speed Wireless-Network. If your TV is connected to a network with an Ethernat cable, you will not see the wireless network connection menu. You must unplug the Ethernet cable to set a wireless network connection. Connecting to a Wireless Network To connect to a wireless network whose network name (SSID) is being broadcast: 1. Press the Menu button on the remote. The on-screen menu is displayed.
3 Connecting to a Hidden Network To connect to a wireless network whose network name (SSID) is not being broadcast: 1. From the NETWORK menu, highlight Hidden Network and press OK. The ENTER ACCESS POINT NAME screen is displayed. 2. Using the on-screen keyboard, enter your network’s name (SSID), then highlight Connect and press OK. 3. Using the on-screen keyboard, enter your network’s password, then highlight Connect and press OK. 4. Press the Exit button on the remote.
3 SETTING TIMERS Setting the Auto Power Off Feature Setting the Timer When activated, the TV’s timer will turn the TV off after a set period of time. 1. Press the Menu button on the remote. The on-screen menu is displayed. 2. Use the Arrow buttons on the remote to highlight Timers and press OK. The TIMERS menu is displayed. 3. Use the Left/Right Arrow buttons on the remote to highlight the period of time after which you want the TV to go to sleep: 30, 60, 90, 120, or 180 minutes.
3 SETTING UP CHANNELS You can use the TV’s Channels menu to: • Find Channels • Select channels to skip • Analog Audio Find Channels • Digital Audio Skip Channels • Set Parental Controls Channels Back Analog Audio Stereo Digital Audio English Parental Controls Scanning for Channels Skipping Channels The TV may need to scan for channels before it can display programs and their associated information.
3 LISTENING TO ALTERNATE AUDIO To use the Digital Language feature: Changing the Analog Audio Language Some analog over-the-air (free) and cable channels broadcast programs in more than one language. The TV’s Analog Audio feature allows you to listen to audio in an alternate language using Secondary Audio Programming (SAP). Not all programs are broadcast in SAP. The Analog Audio Language feature only works when the program being viewed is being broadcast with Secondary Audio Programming.
3 PARENTAL CONTROLS Using Parental Controls The TV’s parental controls allow you to prevent the TV from displaying certain channels or programs without a password. The PARENTAL CONTROLS menu only appears when: Enabling or Disabling Program Ratings To manage program content according to its rating, you must enable the Program Rating feature. To enable or disable the Program Rating feature: 1. From the PARENTAL CONTROLS menu, highlight Locks and press OK. The LOCKS menu is displayed.
3 SETTING UP CLOSED CAPTIONING Your TV can display closed captions for programs that include them. Closed captions display a transcription of a program’s dialogue. If the program you are viewing is not being broadcast with closed captions, the TV will not display them. The Closed Captions menu does not appear when an HDMI input is selected. To activate or deactivate closed captions: 1. Press the Menu button on the remote. The on-screen menu is displayed. 2.
3 Typical choices include: • Opaque background, transparent window—Only a strip of background appears behind the text, expanding as the text appears. This is the typical "As Broadcast" mode. • Opaque background and window in the same color—When text appears, the entire line fills with color at once. Text Background In the example below, the closed caption text is green, the background is black, and the window is red.
3 RENAMING DEVICES ON THE INPUT MENU You can rename the inputs to make them easier to recognize on the INPUT menu. For example, if you have a DVD player connected to the Component input, you can rename that input to display “DVD Player.” See Changing the Input Source. To change the name of an input: 1. Press the Menu button on the remote. The on-screen menu is displayed. 2. Use the Arrow buttons on the remote to highlight Input Settings and press OK. The INPUT SETTINGS menu is displayed. 3.
3 CHANGING THE TV SETTINGS Using the SYSTEM menu, you can: • Check for updates • View system information • Change the on-screen menu language • Set time zone and local settings • Adjust the CEC settings • Have the most control over your TV, switch to Quick Start • Adjust to preserve Aspect Ratio or fill the screen • Customize TV name • Review and maintain the list of paired devices • Adjust accessibility settings • Reset the TV settings & set up administrative controls System Back Ch
3 Setting the Time and Local Settings Adjusting the CEC Settings Adjusting the Power Mode To ensure the correct time is displayed when you press the Info button, set the TV’s time zone: The CEC function on your TV enables you to control devices connected to HDMI (ARC) input with the included remote, without any programming. Using CEC, your VIZIO TV remote can control: Your Display is set to Eco Mode by default. When the Display is powered off, Eco Mode setting uses less than 0.5W of power.
3 Changing the TV Name Naming your TV helps differentiate it from other cast devices you may have in your home. To view your TV name: 1. Press the Menu button on the remote. The on-screen menu is displayed. 2. Use the Arrow buttons on the remote to highlight System and press OK. The SYSTEM menu is displayed. 3. Use the Arrow buttons on the remote to highlight TV Name and press OK. The TV Name is displayed. 4. Enter your custom name using the on-screen keyboard. 5. Press the Exit button on the remote.
3 ACCESSIBILITY SETTINGS VIZIO is committed to providing intuitive, user-friendly products. Your new VIZIO TV offers several accessibility features that can help you get the most out of it. You can use the TV’s RESET & ADMIN menu to restore the TV to its factory default settings as well as access other system settings. Using the RESET & ADMIN, you can: To access the ACCESSIBILITY menu: 1. 2. Press the Menu button on the remote control.
3 Turning the Power Indicator On or Off The Power Indicator on the front of your TV normally does not glow when the TV is on. You can change this setting if you prefer the light to be on. To turn the Power Indicator Light On or Off: SET SYSTEM PIN ABOUT VIEWING DATA You can set a System Pin to use: 1. Picture mode lock 2. Parental controls 1. Press the Menu button on the remote. The on-screen menu is displayed. 3. Reset to TV to factory default setting 2.
3 USING THE INFO WINDOW The Info Window can be displayed by pressing the Info button on the remote: • Press the Info button one time to display the TV name, current input, picture mode, network name, and time.
SmartCast TV™ 4 What is SmartCast TV™? SmartCast TV lets you discover, stream, and control your content like never before. Access top apps like Netflix more easily, using the included remote to browse and launch content directly from the big screen. SmartCast TV makes finding something to watch more fun - discover new shows, including movies in 4K UHD. Plus, you can quickly set up and adjust settings right on the TV using the included remote control.
Playing USB Media Playing USB Media Connect a USB thumb drive to your TV to play videos. 4 Preparing Your USB Drive to Play USB Media Removing the USB Drive from the TV To display USB media, you must first save your videos onto a USB thumb drive: To safely remove your USB drive from the TV: • The USB thumb drive must be formatted as FAT32. • Files on the USB thumb drive must end in a supported file extension (.mp4).
4 Back Button Highlight this button and press OK to return to the previous screen. Connected Sources Displays connected USB devices. Now Playing Information Displays song title, album title, and artist name. Progress Bar Displays the duration of the currently-playing song. The blue bar will lengthen as the song progresses.
4 Back Button Highlight this button and press OK to return to the previous screen. Connected Sources Displays connected USB devices.
4 Back Button Highlight this button and press OK to return to the previous screen. Connected Sources Dispalys connected USB devices. VIZIO View Music Files Current Folder Displays the folder path. USB1: root Start Fullscreen Slideshow View Thumbnails/Folders Adjust Slideshow Settings Back Button Highlight and press OK to return to left column. VIZIO_2GB\Photo\root Photo Current Folder Sort by Date or File Name Folder Contents This area displays the contents of the currently selected folder.
Troubleshooting & Technical Support A Do You Have Questions? Find Answers At SUPPORT.VIZIO.
A Take A Moment To Register Your Product At VIZIO.COM/PRODUCT-REGISTRATION Why Register? Customized Support Get assistance quickly with your information on-hand. News & Offers Take advantage of the latest news and special offers from VIZIO. Safety & Satisfaction Stay up to date with important product updates and notifications.
A HELP TOPICS The remote is not responding. • Make sure the batteries are properly inserted matching the - and + symbols. • Replace the batteries with fresh ones. The TV displays “No Signal.” • Press Input button on the remote control to select a different input source. There is no sound. • Press Volume Up on the remote control. • Press the Mute button on the remote to ensure mute is off. • Check the audio settings. See Adjusting the Audio Settings.
A I see “noise” or static on the screen. • When your TV’s digital capabilities exceed a digital broadcast signal, the signal is up-converted (improved) to match your TV’s display capabilities. This up-converting can sometimes cause irregularities in the image. • If you are using an antenna, the signal strength of the channel may be low. Ensure your antenna is connected securely to the TV and move the antenna around the room or close to a window for the best signal.
Specifications B D43-F1 D50-F1 D55-F2 43” 50” 55” 42.5” 49.5” 54.5” Dimensions w/ Stand 38.36 in x 24.56 in x 8.4 in (97.43 cm x 62.38 cm x 21.34 cm) 44.46 in x 28.27 in x 10.24 in (112.9 cm x 71.81 cm x 26.01 cm) 49.1 in x 30.8 in x 9.8 in (124.7 cm x 78.2 cm x 24.9 cm) Dimensions w/o Stand 38.36 in x 22.39 in x 3.31 in (97.43 cm x 56.87 cm x 8.41 cm) 44.46 in x 25.87 in x 3.31 in (112.9 cm x 65.71 cm x 8.41 cm) 49.1 in x 28.4 in x 3.3 in (124.7 cm x 72.1 cm x 63.
B D60-F3 D65-F1 D70-F3 60” 65” 70” 59.5” 64.5” 69.5” Dimensions w/ Stand 53.50 in x 33.60 in x 10.50 in (135.89cm x 85.34cm x 26.67cm) 57.91 in x 33.39 in x 3.35 in (147.19 cm x 84.81 cm x 8.51 cm) 61.80 in x 38.50 in x 11.10 in (156.97cm x 97.79cm x 28.19cm) Dimensions w/o Stand 53.50 in x 31.00 in x 2.90 in (135.89 cm x 78.74 cm x 7.37 cm) 57.91 in x 33.94 in x 11.66 in (147.1 cm x 91.29 cm x 29.62 cm) 61.80 in x 35.60 in x 2.90 in (156.97cm x 90.42cm x 7.37cm) Weight w/ Stand 43.
Regulatory Information C FCC Class B Radio Interference Statement Notice NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Limited Warranty UNITED STATES AND CANADA BY USING YOUR VIZIO PRODUCT YOU AGREE TO BE BOUND BY ALL THE TERMS OF THIS WARRANTY. BEFORE USING YOUR VIZIO PRODUCT, PLEASE READ THIS WARRANTY CAREFULLY. IF YOU DO NOT AGREE TO THE TERMS OF THIS WARRANTY, DO NOT USE THE VIZIO PRODUCT AND, WITHIN THIRTY (30) DAYS OF THE DATE OF PURCHASE, RETURN IT FOR A REFUND TO THE AUTHORIZED RETAILER WHERE YOU PURCHASED IT.
D then you are entitled to recover attorneys’ fees as the arbitrator may determine. The dispute will be governed by the laws of the state or territory in which you resided at the time of your purchase (if in the United States). The place of arbitration will be Irvine, California, or your county of residence (if in the United States). The arbitrator will have no authority to award punitive or other damages not measured by the prevailing party’s actual damages, except as may be required by statute.
Legal Information Software Licenses All software is provided subject to a software license agreement(s) and you agree that you will be bound by such license agreement(s) in addition to these terms. Your use of this product is subject to VIZIO’s privacy policy, which may be updated from time to time, and is available to view at http://www.vizio.com/privacy.
© 2017 VIZIO INC. ALL RIGHTS RESERVED.
