User Manual
Table Of Contents
- Chapter One Hardware Installation and Initial Configuration
- Section One
- Management over a
- Local Console
- Chapter Two
- Introduction to the Local Console Interface
- Chapter Three
- Configuation Using the Local Console
- The Main Control Portal
- 3-3-1. Basic Search
- 3-3-2. Alarm Search
- 3-3-3. POS Search
- 3-3-4. Smart Search II
- 3-3-5. Smart VCA event search
- 3-3-6. Storyboard
- 3-5-1. Settings - Overview
- 3-5-2. Settings–Camera–Management
- 3-5-3. Settings–Camera–Recording
- 3-5-4. Settings–Camera–Recording
- 3-5-5. Settings–Camera–Media
- 3-5-6. Settings - Camera - Image
- 3-5-7. Settings–Camera–Motion Detection
- 3-5-8. Settings - Camera - PTZ settings
- 3-5-9. Settings - Camera - Port forwarding
- 3-5-10. Settings - Camera - Update firmware
- 3-5-11. Settings–Alarm–Alarm
- 3-5-12. Settings - Alarm - Email
- 3-5-13. Settings–System–Information
- 3-5-14. Settings–System–Maintenance
- 3-5-15. Settings - System - Display
- 3-5-16. Settings - System - UPS
- 3-5-17. Settings - System - Log
- 3-5-18. Settings - System - VIVOCloud service
- 3-5-19. Settings–User
- 3-5-20. Settings–User-Login / Logout
- 3-5-21. Settings–Storage
- 3-5-22. Settings - Storage - Scheduled backup
- 3-5-23. Settings - Network
- Settings - Network - IP
- Settings - DDNS
- Settings–Service
- Section Two
- Management over a Web Console
- Chapter Four Login and Getting Started
- 4-1. Login
- 4-2. Graphical Layout and Screen Elements - Liveview
- 4-2-4. Logo & Menu
- 4-2-5. View Cell panel
- 4-2-6. PTZ panel
- Adding Cameras to View Cells
- 4-2-7. Alarm panel
- 4-3. Graphical Layout and Screen Elements - Search recording clips
- 4-3-4. View Cells in Search Recording Clips
- 4-3-6. Calendar Panel
- 4-3-5. Alarm Panel
- Search Recording Clips Control Panel
- Chapter Five System Settings
- Chapter Six Operation
- Safety and Compatibility
VIVOTEK - Built with Reliability
30 - User's Manual
To power up and power down,
On the initial conguration:
1. Connect the power cord between the system and power outlet.
2. Turn on the system using the power button on the back of chassis.
After the initial connection,
Use the power down button on the lower right corner of the Settings page. The system
should start ushing the cached contents in system memory and gracefully shut down. You
should then ip the power switch button on the back of chassis to completely shut down the
system.
Press the Reset button for longer than 5 seconds can restore system defaults.
Power Up and Power Down
1. No storage system is completely fail-safe. Damage to data might occur due to le system
corruption, operating system malfunction, virus infection, HDD component failures, and so on.
Therefore, it is highly recommended to regularly back up your data, and VIVOTEK disclaims
responsibilities of data loss or recovery.
2. Always power o the system using the power button on the back of chassis. The system is
powered o when you observe that all LEDs go o. Do not disconnect the power cord while
the system is still operating. Doing so will result in data inconsistencies. The normal power-o
procedure allows cached data to be written to disks.
If system buzzer is sounded, move your mouse cursor to reveal the main screen portal, and
then click on the Stop buzzer button.
Serious system faults, such as a missing volume, can trigger the system buzzer. Verify the
cause of system fault and turn o the buzzer.
NOTE:
WARNING:
6