User Manual
Table Of Contents
- Chapter One Hardware Installation and Initial Configuration
- Section One
- Management over a
- Local Console
- Chapter Two
- Introduction to the Local Console Interface
- Chapter Three
- Configuation Using the Local Console
- The Main Control Portal
- 3-3-1. Basic Search
- 3-3-2. Alarm Search
- 3-3-3. POS Search
- 3-3-4. Smart Search II
- 3-3-5. Smart VCA event search
- 3-3-6. Storyboard
- 3-5-1. Settings - Overview
- 3-5-2. Settings–Camera–Management
- 3-5-3. Settings–Camera–Recording
- 3-5-4. Settings–Camera–Recording
- 3-5-5. Settings–Camera–Media
- 3-5-6. Settings - Camera - Image
- 3-5-7. Settings–Camera–Motion Detection
- 3-5-8. Settings - Camera - PTZ settings
- 3-5-9. Settings - Camera - Port forwarding
- 3-5-10. Settings - Camera - Update firmware
- 3-5-11. Settings–Alarm–Alarm
- 3-5-12. Settings - Alarm - Email
- 3-5-13. Settings–System–Information
- 3-5-14. Settings–System–Maintenance
- 3-5-15. Settings - System - Display
- 3-5-16. Settings - System - UPS
- 3-5-17. Settings - System - Log
- 3-5-18. Settings - System - VIVOCloud service
- 3-5-19. Settings–User
- 3-5-20. Settings–User-Login / Logout
- 3-5-21. Settings–Storage
- 3-5-22. Settings - Storage - Scheduled backup
- 3-5-23. Settings - Network
- Settings - Network - IP
- Settings - DDNS
- Settings–Service
- Section Two
- Management over a Web Console
- Chapter Four Login and Getting Started
- 4-1. Login
- 4-2. Graphical Layout and Screen Elements - Liveview
- 4-2-4. Logo & Menu
- 4-2-5. View Cell panel
- 4-2-6. PTZ panel
- Adding Cameras to View Cells
- 4-2-7. Alarm panel
- 4-3. Graphical Layout and Screen Elements - Search recording clips
- 4-3-4. View Cells in Search Recording Clips
- 4-3-6. Calendar Panel
- 4-3-5. Alarm Panel
- Search Recording Clips Control Panel
- Chapter Five System Settings
- Chapter Six Operation
- Safety and Compatibility
VIVOTEK - Built with Reliability
User's Manual - 127
Attribute: The various attributes can vary from dierent HDD manufacturers.
Value: Value for the currently selected attribute.
Worst: Worst value acquired for that attribute.
Threshold: A predened threshold or triggering value. The threshold below which the
normalized value will be considered exceeding specications.
Raw value: The detected parameters for that attribute.
Status: The judgement made to deem the current reading as OK or failed.
Verify:
Three types of check disk actions can be initiated through this button.
Bad block check: Performs read/write test to drive sectors to locate bad blocks. This action
may take several hours to complete.
Fast S.M.A.R.T. test: Tests the electronic and mechanical performance and disk read
performance, including those on disk buer, read head, seek time, and integrity of drive
sectors. The short test is performed on a small section of disk platters, and takes about 2
minutes to complete.
S.M.A.R.T. long test: The long test is more thoroughly and is performed to all drive sectors.
The actual completion time depends on drive sizes and the attributes put to test.
The Check disk functions mentioned above, when performed during active I/Os, can consume
system resources and cause dropped frames with the recording tasks.
Note that disk verify function
requires a volume to be temporarily
disabled; namely, the video
recording will be stopped before
disk verify can be performed.