User Manual
Table Of Contents
- Chapter One Hardware Installation and Initial Configuration
- Section One
- Management over a
- Local Console
- Chapter Two
- Introduction to the Local Console Interface
- Chapter Three
- Configuation Using the Local Console
- The Main Control Portal
- 3-3-1. Basic Search
- 3-3-2. Alarm Search
- 3-3-3. POS Search
- 3-3-4. Smart Search II
- 3-3-5. Smart VCA event search
- 3-3-6. Storyboard
- 3-5-1. Settings - Overview
- 3-5-2. Settings–Camera–Management
- 3-5-3. Settings–Camera–Recording
- 3-5-4. Settings–Camera–Recording
- 3-5-5. Settings–Camera–Media
- 3-5-6. Settings - Camera - Image
- 3-5-7. Settings–Camera–Motion Detection
- 3-5-8. Settings - Camera - PTZ settings
- 3-5-9. Settings - Camera - Port forwarding
- 3-5-10. Settings - Camera - Update firmware
- 3-5-11. Settings–Alarm–Alarm
- 3-5-12. Settings - Alarm - Email
- 3-5-13. Settings–System–Information
- 3-5-14. Settings–System–Maintenance
- 3-5-15. Settings - System - Display
- 3-5-16. Settings - System - UPS
- 3-5-17. Settings - System - Log
- 3-5-18. Settings - System - VIVOCloud service
- 3-5-19. Settings–User
- 3-5-20. Settings–User-Login / Logout
- 3-5-21. Settings–Storage
- 3-5-22. Settings - Storage - Scheduled backup
- 3-5-23. Settings - Network
- Settings - Network - IP
- Settings - DDNS
- Settings–Service
- Section Two
- Management over a Web Console
- Chapter Four Login and Getting Started
- 4-1. Login
- 4-2. Graphical Layout and Screen Elements - Liveview
- 4-2-4. Logo & Menu
- 4-2-5. View Cell panel
- 4-2-6. PTZ panel
- Adding Cameras to View Cells
- 4-2-7. Alarm panel
- 4-3. Graphical Layout and Screen Elements - Search recording clips
- 4-3-4. View Cells in Search Recording Clips
- 4-3-6. Calendar Panel
- 4-3-5. Alarm Panel
- Search Recording Clips Control Panel
- Chapter Five System Settings
- Chapter Six Operation
- Safety and Compatibility
VIVOTEK - Built with Reliability
User's Manual - 11
Rear View
9
1
3
4
5
8
10
2
6
7
1 PoE ports # 1 to #16 (ND9424P) 6 Audio OUT
2 RJ45 port - GbE uplink 7 VGA
3 HDMI 8 DI/DO terminal block
4 USB 3.0 port 9 Reset button
5 Audio IN 10 Power socket (110/240V AC), w/ a power
button
IMPORTANT:
It is important to leave a clearance of 25cm behind the chassis. The clearance is required to
ensure an adequate airow through the chassis to ventilate heat.
25cm
To ensure normal operation, maintain ambient airow. Do not block the airow around chassis
such as placing the system in a closed cabinet.
NOTE:
You can also use the Reset button to restore system defaults. Press and hold down the button
for longer than 5 seconds. The system should start restoring defaults.
IMPORTANT:
The total power budget for the ND9322P’s 8 PoE ports is 120W.
The total power budget for the ND9424P’s 16 PoE ports is 200W. Every 8 ports (#1 ~ #8 or #9 ~
#16) provides 100W.
Please ensure the camera PD specication meet the NVR PSE power supply specication be-
fore installation.