IP9164-HT IP9164-LPC Box Network Camera User ’s Manual 2MP • License Plate Capture • P-iris/DC-iris • H.265 • WDR Pro • Remote Back Focus Smart Stream III • SNV II • 3DNR Rev. 1.
VIVOTEK Table of Contents Overview �������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3 Revision History ����������������������������������������������������������������������������������������������������������������������������������������������������� 3 Read Before Use ����������������������������������������������������������������������������������������������������������������������������
VIVOTEK Recording > Recording settings �������������������������������������������������������������������������������������������������������������� 148 Storage > Storage management �������������������������������������������������������������������������������������������������������������� 153 Storage > Content management �������������������������������������������������������������������������������������������������������������� 156 Appendix ���������������������������������������������������������
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below.
VIVOTEK Physical Description Front Panel Light Sensor Lens Rear Panel MicroSD Card Slot Audio In BNC connector Audio Out Recessed Reset Button General I/O Terminal Block Grounding screw Ethernet 10/100 RJ45 Socket Status LED IMPORTANT: If DC power is preferred, it should comply with: O/P: 12VDC, 2A min., L.P.S. per IEC 60950-1. Si l'alimentation CC est préférable, elle devrait être conforme avec ce qui suit : Sortie : 12 VCC, 2 A min., alimentation limitée à conformité CEI 60950-1.
VIVOTEK IMPORTANT: 1. The wire gauge for the required protective earth conductor is 18AWG (green and yellow). 2. Ensure to connect one end to the protective earth terminal and the other to earth. NOTE: Camera Hardware Preventative Maintenance: 1. Visual inspection of all major components including accessories, cabling and connections where accessible for signs of deterioration or damage. 2. Check and clean cameras, lenses and housings inside and out as needed.
VIVOTEK IMPORTANT: For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application programming interface. The HTTP-based camera interface provides the functionality to request a single image, control camera functions (PTZ, output relay etc.), and get and set internal parameter values. The image and CGI-requests are handled by the built-in Web server.
VIVOTEK Hardware Installation 1. Jot down the camera's MAC address for later reference. XXXXXX 0002D10766AD 1 2. Install the lens module to the camera. 3. Connect the iris control cable to the socket on the camera.
VIVOTEK 4. Install the camera stand to camera. 5. Connect an Ethernet cable to the camera. When choosing the lens for your camera, please notice the specifications as below. The screw mount (distance A-C) must be shorter than 5.2mm; in case that the bottom of screw mount may hit the IR Cut Filter.
VIVOTEK 6. Install a MicroSD card, and, if preferred, connect DI/DO wires to the terminal block. The AC/DC pins can accept either 12V or 24V power input. AC24V has with no polarity. 64GB 10 1 I 1 2 3 4 5 6 7 8 9 10 AC/DC- pw 12V or 24V AC/DC+ pw RS485+ RS485DI- (common GND for all DIs) DI2+ DI1+ DO2DO1DO+ (5V) Pin 1 is on the left. 12345678910 The DO pin can provide a 5V output, and the max. load is 50mA.
VIVOTEK DI/DO Diagram Dry contact with external DC power source to supply a relay. Dry contact is the safest connection to protect devices. DIDO+ DI+ Switch DOPhoto Coupler DC External DC power DC 0V DC 0V AC External AC power with Protected Earth NC NO PE Relay External Device PE Wet contact with external DC power source to supply a relay. DIDO+ DI+ Switch DODC 0V DC External DC power AC NO NC PE Relay PE External AC power with Protected Earth External Device 1.
VIVOTEK Dry contact and using camera’s DO+ to supply a relay. DIDO+ DI+ Switch DO- AC NO NC External AC power with Protected Earth PE Relay External Device PE 7. Please visit VIVOTEK’s website to Install the "Shepherd” software utility. The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN. Double-click on the camera’s MAC address to open a web console with the camera.
VIVOTEK 8. Remove the sticker on the light sensor. 9. With a live view on screen, enter Configuration > Image > Focus to adjust the image zoom and focus. Click on the Auto focus button and let the camera find an optimal focus.
VIVOTEK If you purchased a larger lens, make sure the light sensor is not blocked by the lens. You can purchase the AE-237/241/242 enclosure for outdoor installations. LED Definitions Item LED status LED De`finitions 1 2 3 4 5 Steady Red Description Powered and system booting, or network failed Power off Network is disconnected Connected to network Red LED off Green LED off Steady Red and Green LED blinks every 1 sec. Green LED blinks every 1 sec.
VIVOTEK Software Installation 10. Install the Shepherd utility, which helps you locate and configure your Network Camera in the local network. If your camera comes without the CD, go to VIVOTEK’s website, and locate the utility in the Downloads > Software page. 10-1. Run the Shepherd utility. 10-2. The program will conduct an analysis of your network environment.
VIVOTEK 10-3. The program will search for all VIVOTEK network devices on the same LAN. 10-4. After a brief search, the installer window will prompt. Click on the MAC and model name that matches the one printed on the product label. You can then double-click on the address to open a management session with the Network Camera. Network Camera Model No: IP9165-LPC MAC:0002D1730202 R o HS This device complies with part 15 of the FCC rules.
VIVOTEK Some, but not all special ASCII characters are supported: !, $, %, -, ., @, ^, _, and ~. You can use them in the password combination. 11-2. Another prompt will request for the password you just configured. Enter the password and then you can start configure your camera and see the live view.
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press the recessed reset button. Wait for the Network Camera to reboot. Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all settings will be restored to factory default.
VIVOTEK When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a nonPoE switch. PoE Power Injector (optional) Non-PoE Switch NOTE: 1. The camera is only to be connected to PoE networks without routing to outside plants. 2. For PoE connection, use only UL listed I.T.E. with PoE output. 1. La caméra ne doit être raccordée qu’à des réseaux PoE, sans routage vers des installations extérieures. 2.
VIVOTEK 2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192.168.0.3, please forward the following ports for the Network Camera on the router. ■ HTTP port: default is 80 ■ RTSP port: default is 554 ■ RTP port for video: default is 5556 ■ RTCP port for video: default is 5557 If you have changed the port numbers on the Network page, please open the ports accordingly on your router.
VIVOTEK For more information with network configuration options (such as that of streaming ports), please refer to Configuration > Network Settings. VIVOTEK also provides the automatic port forwarding feature as an NAT traversal function with the precondition that your router must support the UPnP port forwarding feature.
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also download and install the 32-channel recording software from VIVOTEK's website in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: 1. Launch your web browser (e.g., Microsoft® Internet Explorer or Mozilla Firefox). 2.
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 101. ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX ® Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. 2.
VIVOTEK IMPORTANT: • Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT open a management/view session to the camera using a 64-bit IE browser. • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64. A 32-bit version of IE browser will be installed. • On Windows 7, the 32-bit explorer browser can be accessed from here: C:\Program Files (x86)\Internet Explorer\iexplore.
VIVOTEK Using RTSP Players To view the streaming media using RTSP players, you can use one of the following players that support RTSP streaming. Quick Time Player VLC media player VLC media player 1. Launch the RTSP player. mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3.
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 18. To utilize this feature, please check the following settings on your Network Camera: 1.
VIVOTEK Using VIVOTEK Recording Software The product software CD also contains a VAST recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras. Please install the recording software; then launch the program to add the Network Camera to the Channel list. For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www.vivotek.com.
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window. Resize Buttons VIVOTEK INC. Logo Host Name Configuration Area Camera Control Area Hide Button Live View Window VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website. Host Name The host name can be customized to fit your needs.
VIVOTEK Configuration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 34. Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a password be applied to the Network Camera so that only the administrator can configure the Network Camera. For more information, please refer to Configuration on page 39.
VIVOTEK PTZ Panel: This Network Camera supports “digital“ (e-PTZ) pan/tilt/zoom control, which allows roaming a smaller view frame within a large view frame. Please refer to PTZ settiings on page 116 for detailed information. Global View: Click on this item to display the Global View window. The Global View window contains a full view image (the largest frame size of the captured video) and a floating frame (the viewing region of the current video stream).
VIVOTEK Video Control Buttons: Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot: Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format. Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation.
VIVOTEK Mute: Turn off the Mic volume on the local computer. The button becomes the after clicking the Mute button. Mic On button Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal mode. ■ The following window is displayed when the video mode is set to MJPEG: Video Title Title and Time Video (HTTP-V) 2018/02/25 17:08:56 Time Video 17:08:56 2018/02/25 Video Control Buttons Video Title: The video title can be configured.
VIVOTEK Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. H.265/H.264 Media Options Select to stream video or audio data or both. This is enabled only when the video mode is set to H.264 or H.265. H.265/H.264 Protocol Options Depending on your network environment, there are four transmission modes of H.264 or H.
VIVOTEK Two way audio Half duplex: Audio is transmitted from one direction at a time, e.g., from a PC holding a web console with the camera. Full duplex: Audio is transmitted in both directions simultaneously. MP4 Saving Options Users can record live video as they are watching it by clicking page. Here, you can specify the storage destination and file name. Start MP4 Recording on the main Folder: Specify a storage destination on your PC for the recorded video files. The location can be changed.
VIVOTEK Joystick settings Enable Joystick Connect a joystick to a USB port on your management computer. Supported by the plug-in (Microsoft’s DirectX), once the plug-in for the web console is loaded, it will automatically detect if there is any joystick on the computer. The joystick should work properly without installing any other driver or software. Then you can begin to configure the joystick settings of connected devices. Please follow the instructions below to enable joystick settings. 1.
VIVOTEK Buttons Configuration In the Button Configuration window, the left column shows the actions you can assign, and the right column shows the functional buttons and assigned actions. The number of buttons may differ from different joysticks. Please follow the steps below to configure your joystick buttons: 1. Choosing one of the actions and click Assign will pop up a dialog. Then you can assign this action to a button by pressing the joystick button or select it from the drop-down list.
VIVOTEK Buttons Configuration Click the Configure Buttons button, a window will prompt as shown below. Please follow the steps below to configure your joystick buttons: 1. Select a button number from the Button # pull-down menu. Tips: If you are not sure of the locations of each button, use the Properties window in the Game Controllers utility. 2. Select a corresponding action, such as Patrol or Preset#. 3. Click the Assign button to assign an action to the button.
VIVOTEK Configuration Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. VIVOTEK provides an easy-to-use user interface that helps you set up your network camera with minimal effort. In order to simplify the user interface, detailed information will be hidden unless you click on the function item.
VIVOTEK System > General settings This section explains how to configure the basic settings for the Network Camera, such as the host name and system time. It is composed of the following two columns: System, and System Time. When finished with the settings on this page, click Save at the bottom of the page to enable the settings. System Host name: Enter a desired name for the Network Camera.
VIVOTEK System > Homepage layout This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the second tab on this page). The settings will be displayed automatically in this Preview field. The following shows the homepage using the default settings: ■ Hide Powered by VIVOTEK: If you check this item, it will be removed from the homepage.
VIVOTEK Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings.
VIVOTEK ■ Follow the steps below to set up the customed homepage: 1. Click Custom on the left column. 2. Click the field where you want to change the color on the right column. Color Selector Custom Pattern 3. The palette window will pop up as shown below. 2 3 1 4 4. Drag the slider bar and click on the left square to select a desired color. 5. The selected color will be displayed in the corresponding fields and in the Preview column. 6. Click Save to enable the settings.
VIVOTEK System > Logs This section explains how to configure the Network Camera to send the system log to a remote server as backup. Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log. 2. In the IP address text box, enter the IP address of the remote server. 2. In the port text box, enter the port number of the remote server. 3. When completed, click Save to enable the setting.
VIVOTEK You can install the included VAST recording software, which provides an Event Management function group for delivering event messages via emails, GSM short messages, onscreen event panel, or to trigger an alarm, etc. For more information, refer to the VAST User Manual.
VIVOTEK Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order. The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit. System > Parameters The View Parameters page lists the entire system’s parameters. If you need technical assistance, please provide the information listed on this page.
VIVOTEK System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to complete the process. Note: Do not power off the Network Camera during the upgrade! Follow the steps below to upgrade the firmware: 1. Download the latest firmware file from the VIVOTEK website. The file is in .pkg file format. 2.
VIVOTEK General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network: Select this option to retain the Network Type settings (please refer to Network Type on page 81). Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to Import/Export files below on this page). Custom Language: Select this option to retain the Custom Language settings.
VIVOTEK Import/Export files This feature allows you to Export / Update daylight saving time rules, custom language file, configuration file, and server status report. Export daylight saving time configuration file: Click to set the start and end time of DST (Daylight Saving). Follow the steps below to export: 1. In the Export files column, click Export to export the daylight saving time configuration file from the Network Camera. 2. A file download dialog will pop up as shown below.
VIVOTEK 3. Open the file with Microsoft® Notepad and locate your time zone; set the start and end time of DST. When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in November. Update daylight saving time rules: Click Browse… and specify the XML file to update. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera.
VIVOTEK The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文. Update custom language file: Click Browse… and specify your own custom language file to upload. Export configuration file: Click to export all parameters for the device and user-defined scripts.
VIVOTEK Media > Image This section explains how to configure the image settings of the Network Camera. It is composed of the following four columns: General settings, Picture settings, Exposure, and Privacy mask. The Focus window is available only for models that come with motorized lens. General settings Video title Show_timestamp_and video_title_in_video_and_snapshots: Enter a name that will be displayed on the title bar of the live video as the picture shown below.
VIVOTEK Video orientation: Flip - vertically reflect the display of the live video; Mirror - horizontally reflect the display of the live video. Select both options if the Network Camera is installed upside-down (e.g., on the ceiling) to correct the image orientation. Please note that if you have preset locations, those locations will be cleared after flip/mirror setting. Rotate - Normal Flip Mirror Rotate 90° clockwise The rotation here indicates clockwise rotation.
VIVOTEK IR cut filter With a removable IR-cut filter, this Network Camera can automatically remove the filter to let IR light enter the light sensor during low light conditions. ■ Auto mode The Network Camera automatically removes the filter by judging the level of ambient light. ■ Day mode In day mode, the Network Camera switches on the IR cut filter at all times to block infrared light from reaching the sensor so that the colors will not be distorted.
VIVOTEK Illuminators Turn on external IR illuminator in night mode Select this to turn on the external IR illuminator when the camera detects low light condition and enters the night mode. A Digital Output connection to an external IR is needed. Smart IR Anti-overexposure: When enabled, the camera automatically adjusts the IR projection to adjacent objects in order to avoid over-exposure in the night mode.
VIVOTEK Tips: If there is an object in close proximity, the IR lights reflected back from it can mislead the Smart IR’s calculation of light level. To solve this problem, you can place an “Exposure Exclude” window on an unavoidable object in the Exposure setting window. See page 56 for how to do it. You can also configure the “Exposure Exclude” window in a night mode “Profile” setting so that your day time setting is not affected.
VIVOTEK Image settings On this page, you can tune the White balance and Image adjustment. Sensor Setting 2: For special situations Sensor Setting 1: For normal situations White balance: Adjust the value for the best color temperature. ■ You may follow the steps below to adjust the white balance to the best color temperature. 1.
VIVOTEK Noise reduction ■ Enable noise reduction: Check to enable noise reduction in order to reduce noises and flickers in image. This applies to the onboard 3D Noise Reduction feature. Use the pull-down menu to adjust the reduction strength. Note that applying this function to the video channel will consume system computing power. 3D Noise Reduction is mostly applied in low-light conditions. When enabled in a low-light condition with fast moving objects, trails of after-images may occur.
VIVOTEK Exposure On this page, you can configure the Exposure measurement window, Exposure level, Exposure mode, Exposure time, Gain control, and Day/Night mode settings. You can configure two sets of Exposure settings: one for normal situations, the other for special situations, such as the day/night/ schedule mode. Sensor Setting 2: For special situations Sensor Setting 1: For normal situations Measurement Window: This function allows users to set measurement window(s) for low light compensation.
VIVOTEK Tips: • The LPC model comes with pre-configured firmware for special Exposure > Shutter Priority configuration. That aims for traffic monitoring and control applications. Normally you need not change the related Exposure settings here. The inclusive window refers to the “weighed window“; the exclusive window refers to “ignored window“. It adopts the weighted averages method to calculate the value. The inclusive windows have a higher priority.
VIVOTEK ■ AE Speed Adjustment: This function applies when you need to monitor fast changing lighting conditions. For example, the camera may need to monitor a highway lane or entrance of a parking area at night where cars passing by with their lights on can bring fast changes in light levels. The same applies if the camera is installed on a vehicle, and when it needs to adapts to fast changes of light when entering and leaving a tunnel.
VIVOTEK Please follow the steps below to set up a profile: 1. Select the Profile mode tab. 2. Select the applicable mode: Night mode or Schedule mode. Please manually enter a range of time if you choose the Schedule mode. 3. Configure Exposure control settings in the folowing columns. Please refer to previous dicussions for detailed information. 4. Click Save to enable the setting and click Close to exit the page.
VIVOTEK Focus (This function applies when using the auto focus lens) Focus here refers to the Remote Focus, is applicable to Network Cameras that are equipped with stepping motor lens. The automated focus adjustment function eliminates the needs to physically adjust camera focus. In an outdoor deployment consisting of a large number of cameras, the auto focus function can be very helpful when these cameras become out of focus after days or weeks of operation.
VIVOTEK If using an iCS lens model, use the auto focus function for an optimal image. The configuration page automaticallly displays different options according to the lens you installed.
VIVOTEK Below is the procedure to perform the automated Focus function: 1. Select from the bottom of the screen whether you want to perform focus adjustment on the Full view or within a Custom focus window. You can create a custom window and click and drag the window to a desired position on screen. 2. It is recommended to Reset to the default back focus position of the sensor board. 3. You can use the Open iris checkbox (default) to increase the iris size for a better focus adjustment result. 4.
VIVOTEK Privacy mask Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to address privacy concerns. ■ To set the privacy mask windows, follow the steps below: 1. Click New to add a new window. 2. You can use 4 mouse clicks to create a new masking window, which is recommended to be at least twice the size of the object (height and width) you want to cover. 3. Enter a Window Name and click Save to enable the setting. 4.
VIVOTEK Media > Video Mode - Resolution and Frame rate With the WDR Pro enabled for the high-contrast environment, the maximum frame rate is 30fps. Without the WDR function, you can enjoy a higher frame rate for up to 60fps (e.g., in traffic monitoring).
VIVOTEK Stream settings This Network Camera supports multiple streams with frame sizes ranging from 640 x 360 to 1920 x 1080 pixels. ■ Stream 1: The default frame size for Stream 2 is set to the 1920 x 1080. ■ Stream 2: The default frame size for Stream 2 is set to the 640 x 360. ■ Stream 3: Users can define the "Region of Interest" (viewing region) and the "Output Frame Size" (size of the live view window). Click Viewing Window to open the viewing region settings page.
VIVOTEK Please follow the steps below to set up those settings for a stream: 1. Select a stream for which you want to set up the viewing region. 2. Select a Region of Interest from the drop-down list. The floating frame, the same as the one in the Global View window on the home page, will resize accordingly. If you want to set up a customized viewing region, you can also resize and drag the floating frame to a desired position with your mouse. 3.
VIVOTEK Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing Window sections. This Network Camera offers real-time H.265, H.264, and MJPEG compression standards (Triple Codec) for real-time viewing. If the H.264 or H.265 mode is selected, the video is streamed via the RTSP protocol.
VIVOTEK ■ Intra frame period Determine how often for firmware to plant an I frame. The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds. ■ Smart stream III ►Dynamic Intra frame period High quality motion codecs, such as H.
VIVOTEK With the H.265 codec in an optimal scenario and when Dynamic Intra frame is combined with the Smart Stream function, an 80% of bandwidth saving can be achieved compared with using H.264 without enabling these bandwidth-saving features. ■ Smart FPS In a static scene, the algorithm re-encodes old frames when no motions occur in scene. When motions occur, the encoding returns to normal to deliver real-time streaming.
VIVOTEK ►Smart codec: Smart codec effectively reduces the quality of the whole or the non-interested areas on a screen and therefore reduces the bandwidth consumed. You can manually specify the video quality for the foreground and the background areas. Select an operation mode if Smart codec is preferred. - Auto tracking: The Auto mode configures the whole screen into the non-interested area. The video quality of part of the screen returns to normal when one or more objects move in that area.
VIVOTEK As the result, the lower screen is constantly displayed in high details, while the upper half is transmitted using a lower-quality format. Although the upper half is transmitted using a lower quality format, you still have an awareness of what is happening on the whole screen.
VIVOTEK ■ Video quality Constant bit rate: • Constant bit rate: A complex scene generally produces a larger file size, meaning that higher bandwidth will be needed for data transmission. The bandwidth utilization is configurable to match a selected level, resulting in mutable video quality performance.
VIVOTEK • Fixed quality: On the other hand, if Fixed quality is selected, all frames are transmitted with the same quality; bandwidth utilization is therefore unpredictable. The video quality can be adjusted to the following settings: Medium, Standard, Good, Detailed, and Excellent. You can also select Customize and manually enter a value.
VIVOTEK If JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. Because the media contents are a combination of JPEG images, no audio data is transmitted to the client.
VIVOTEK Media > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the following message is displayed: External microphone input: Select the gain of the external audio input according to ambient conditions. Adjust the gain from +21 db (most sensitive) or -33 db (least sensitive).
VIVOTEK Audio clips ■ Output gain: Use the slide bar to change the audio output gains value. ■ Audio clip: When the camera's audio input is connected to a microphone, you can record a short period of audio recordings (1 to 10 seconds). You can also use the camera's embedded microphone to record an audio clip, if available. Because the memory space is limited, a recording count down will be available on screen. You can also upload an audio file to the camera's flash memory.
VIVOTEK Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network Type is LAN. Please rememer to click on the Save button when you complete the Network setting.
VIVOTEK Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer names and IP addresses. Secondary WINS server: The secondary WINS server that maintains the database of computer names and IP addresses.
VIVOTEK NOTE: ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera. ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support UPnP port forwarding. ► Steps to enable the UPnP TM user interface on your computer: Note that you must log on to the computer as a system administrator to install the UPnP TM components. 1.
VIVOTEK 4. In the Networking Services dialog box, select Universal Plug and Play and click OK. 5. Click Next in the following window. 6. Click Finish. UPnP TM is enabled. ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices added to a network. Services and capabilities offered by networked devices, such as printing and file sharing, are available among each other without the need for cumbersome network configuration.
VIVOTEK Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with a link-local IPv6 address accordingly. IPv6 Information: Click this button to obtain the IPv6 information as shown below.
VIVOTEK Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
VIVOTEK 86 - User's Manual
VIVOTEK Network > Streaming protocols HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 101 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security settings for an HTTP transaction: basic and digest.
VIVOTEK URL command -- http://:/ For example, when the Access name for stream 2 is set to video1s2.mjpg: 1. Launch Mozilla Firefox or Netscape. 2. Type the above URL command in the address bar. Press Enter. 3. The JPEG images will be displayed in your web browser. http://192.168.5.151/video1s2.
VIVOTEK Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted. If digest authentication is selected, user credentials are encrypted using MD5 algorithm, thus providing better protection against unauthorized access.
VIVOTEK Multicast settings for streams: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for video streams. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.
VIVOTEK SIP SIP is short for Session Initiation Protocol. If necessary, you can change the default port number, 5060, to one between 1025 and 65535. Two way audio port: The Network Camera supports two way audio communication so that operators can transmit and receive audio simultaneously. By using the Network Camera’s built-in or external microphone and an external speaker, you can communicate with people around the Network Camera.
VIVOTEK Audio is being transmitted to the Network Camera 2011/03/09 17:08:56 Video (TCP-AV) Talk Button Click Mic Volume Mute to enable audio transmission to the Network Camera; click microphone; click 92 - User's Manual to turn off the audio. To stop talking, click again.
VIVOTEK Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Express Link is a free service provided by VIVOTEK server, which allows users to register a domain name for a network device. One URL can only be mapped to one MAC address.
VIVOTEK Manual setup DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting. Provider: Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net, a free dynamic domain name service, to VIVOTEK customers. It is recommended that you register Safe100.net to access VIVOTEK’s Network Cameras from the Internet. Additionally, we offer other DDNS providers, such as Dyndns.org(Dynamic), Dyndns. org(Custom), TZO.com, DHS.
VIVOTEK [Register] Successfully Your account information has been mailed to registered e-mail address 4. Select Enable DDNS and click Save to enable the setting. ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators. You can use CustomSafe100 to register a dynamic domain name if your distributor or system integrators offer such services. 1. In the DDNS column, select CustomSafe100 from the drop-down list. 2.
VIVOTEK Network > QoS (Quality of Service) Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network. Quality of service guarantees are important if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
VIVOTEK QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64 different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop Behavior (PHB).
VIVOTEK Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. It helps network administrators to remotely manage network devices and find, solve network problems with ease. ■ The SNMP consists of the following three key components: 1.
VIVOTEK Network > FTP The newer firmware disabled the FTP port for security concerns. You can manually enable the FTP server service to enable the FTP function. You can disable the FTP server function when it is not in use. FTP port: The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Shepherd utility to upgrade the firmware via FTP server. By default, the FTP port is set to 21. It can also be assigned to another port number between 1025 and 65535.
VIVOTEK Bonjour To access the camera from a Mac computer, go to Safari, click on Bonjour and select the camera from a drop-down list. You can go to Safari > Preferences to enter your user name and password, and provide the root password the first time you access the camera. The camera main page will open in your browser. Some later iOSes may come without the Bonjour option. Install the Discovery utility instead. Find the Discovery (formerly Bonjour Browser) from the Mac App Store.
VIVOTEK Security > User accounts This section explains how to enable password protection and create multiple accounts. Account management The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Account management window, please apply the password for the “root” account first. The administrator can create up to 20 user accounts. To create a new user, 1. Click to unfold the pull-down menu. Select New user. 2.
VIVOTEK Privilege management Digital Output & PTZ control: You can modify the management privilege as operators or viewers. Select or de-select the checkboxes, and then click Save to enable the settings. If you give Viewers the privilege, Operators will also have the ability to control the Network Camera through the main page. (Please refer to Configuration on page 39). Allow anonymous viewing: If you select this item, any client can access the live stream without entering a User ID and Password.
VIVOTEK Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Install Certificate Method Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
VIVOTEK 5. Click Save to preserve your configuration, and your current session with the camera will change to the encrypted connection. 6. If your web session does not automatically change to an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS. https:// https://192.168.5.151/index.
VIVOTEK Create certificate request and install 1. Select the option from the Method pull-down menu. 2. Click Create certificate to proceed. 3. The following information will show up in a pop-up window after clicking Create. Then click Save to generate the certificate request. 4. The Certificate request window will prompt. If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups.
VIVOTEK 5. Look for a trusted certificate authority, such as Symantec’s VeriSign Authentication Services, that issues digital certificates. Sign in and purchase the SSL certification service. Copy the certificate request from your request prompt and paste it in the CA’s signing request window. Proceed with the rest of the process as CA’s instructions on their webpage. 6. Once completed, your SSL certificate should be delivered to you via an email or other means.
VIVOTEK 7. Open a new edit, paste the certificate contents, and press ENTER at the end of the contents to add an empty line. 8. Convert file format from DOS to UNIX. Open File menu > Conversions > DOS to Unix.
VIVOTEK 9. Save the edit using the “.crt” extension, using a file name like “CAcert.crt.” 10. Return to the original firmware session, use the Browse button to locate the crt certificate file, and click Upload to enable the certification.
VIVOTEK 11. When the certifice file is successfully loaded, its status will be stated as Active. Note that a certificate must have been created and installed before you can click on the “Save" button for the configuration to take effect. 12.To begin an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS.
VIVOTEK Security > Access List This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link (IE Explorer or Quick Time Player).
VIVOTEK ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explore or Quick Time Player). If you want to enable the denied list, please check Enable access list filtering and click Save in the first column.
VIVOTEK There are three types of rules: Single: This rule allows the user to add an IP address to the Allowed/Denied list. For example: 192.168.2.1 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. The address and network mask are written in CIDR format. For example: IP address range 192.168.2.x will be bolcked. If IPv6 filter is preferred, you will be prompted by the following window.
VIVOTEK Security > IEEE 802.1X Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x standard is designed to enhance the security of local area networks, which provides authentication to network devices (clients) attached to a network port (wired or wireless).
VIVOTEK 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically. NOTE: ► The authentication process for 802.1x: 1. The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the supplicant) and the RADIUS Server (the authentication server). 2. A Network Camera requests access to the protected LAN using 802.
VIVOTEK Security > Miscellaneous The embedded TrendMicro utitlity provides the protection against Cross-Site Request Forgery. Cross-site request forgery is also known as one-click attack or session riding and is abbreviated as CSRF. CSRF is a type of malicious exploit of a website, in this case, the camera. Unauthorized commands are transmitted from a user that the web application trusts, using the mechanism of forging a trusted user's own request with a request containing his own cookies, etc.
VIVOTEK PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. 1. Digital: Control the e-PTZ operation. Within a field of view, it allows users to quickly move the focus to a target area for close-up viewing without physically moving the camera. 2. Mechanical: Connect the Network Camera to a PTZ driver or scanner via the RS485 interface. Digital PTZ Operation (E-PTZ Operation) The e-PTZ control settings section will be displayed as shown below: x1.8 x1.
VIVOTEK Home page in the E-PTZ Mode x3.3 ■ The e-Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected position. ■ If you have set up different preset positions for different streams, you can select one of the video streams to display its separate preset positions.
VIVOTEK Patrol settings You can select some preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click . 2. The selected preset locations will be displayed on the Patrol locations list. 3. Set the Dwelling time for the preset location during an auto patrol. 4. If you want to delete a preset location from the Patrol locations list, select it and click Remove. 5.
VIVOTEK PTZ Mechanical PTZ Operation Select the “Mechanical” tab to display the RS485 Settings: RS485 Settings Disable: Select this option to disable this function. PTZ camera: Select this option to enable PTZ operation. To utilize this feature, please connect the Network Camera to a PTZ driver or scanner via RS485 serial interface first. Then you can configure the PTZ driver and RS485 port with the following settings.
VIVOTEK Transparent HTTP Tunnel: If you want to use your own RS-485 device, you can use UART commands to build a Transparent HTTP Tunnel. The UART commands will be sent through HTTP tunnel established between the RS-485 device and the camera. For detailed application notes, please refer to URL Commands started on page 159 or https://vivotek.force.com/Customers/s/ to search for the article.
VIVOTEK Home page in Mechanical PTZ Mode The Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected preset position. NOTE: ► The Preset Positions will also be displayed on the Home page. Select one from the Go to menu, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol along the selected positions repeatedly.
VIVOTEK Event > Event settings This section explains how to configure the Network Camera to respond to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. Click on Help, there is an illustration shown in the pop-up window explaining that an event can be triggered by many sources, such as motion detection or external digital input devices.
VIVOTEK ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect next event after seconds: Enter the duration in seconds to pause motion detection after a motion is detected. This can prevent event-related actions to take place too frequently. 1.
VIVOTEK ■ Audio detection A preset threshold can be configured with an external microphone as the trigger to system event. The triggering condition can be an input exceeding or falling below a threshold. Audio detection can take place as a complement to motion detection or as a method to detect activities not covered by the camera's view. ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with.
VIVOTEK Once the triggers are configured, they will be listed under the VADP option. 3. Action Define the actions to be performed by the Network Camera when a trigger is activated. ■ Trigger digital output for seconds Select this option to turn on the external digital output device when a trigger is activated. Specify the length of the trigger interval in the text box.
VIVOTEK ■ Play audio clip: A pre-loaded audio clip can be configured to be played when one triggering condition is met. For example, when an intruder is detected, the event plays a warning message to deter an intruder. ■ Backup media if the network is disconnected Select this option to backup media file on SD card if the network is disconnected. This function will only be displayed after you set up a network storage (NAS).
VIVOTEK Add server It is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server to open the server setting window. You can specify where the notification messages are sent to when a trigger is activated. A total of 5 server settings can be configured. There are four choices of server types available: Email, FTP, HTTP, and Network storage.
VIVOTEK To verify if the email settings are correctly configured, click Test. The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings. Note that after you configure the first event server, the new event server will automatically display on the Server list. If you wish to add other server options, click Add server. Server type - FTP Select to send the media files to an FTP server when a trigger is activated.
VIVOTEK ■ Passive mode Most firewalls do not accept new connections initiated from external requests. If the FTP server supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the firewall. The firmware default has the Passive mode checkbox selected. To verify if the FTP settings are correctly configured, click Test. The result will be shown in a pop-up window as shown below. If successful, you will also receive a test.txt file on the FTP server.
VIVOTEK Network storage: Select to send the media files to a networked storage when a trigger is activated. Please refer to NAS server on page 151 for details. Note that only one NAS server can be configured. Click Save server to enable the settings. ■ SD Test: Click to test your SD card. The system will display a message indicating the result as a success or a failure. If you want to use your SD card for local storage, please format it before use. Please refer to page 132 for detailed information.
VIVOTEK Click 20200120 to open the directory: The format is: HH (24r) Click to open the file list for that hour 2020/01/20 2020/01/20 Click to go back to the previous level of the directory Click to delete selected items Click to delete all recorded data 2020/01/20 2020/01/20 The format is: File name prefix + Minute (mm) You can set up the file name prefix on Add media page. Please refer to next page for detailed information.
VIVOTEK Add media Click Add media to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item to display the detailed configuration options. You can configure any or all of them. Media type - Snapshot Select to send snapshots when a trigger is activated. ■ Media name: Enter a name for the media setting.
VIVOTEK ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Snapshot_20200113_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Note that after you set up the first media server, a new column for media server will automatically display on the Media list. If you wish to add more media options, click Add media.
VIVOTEK ■ Maximum file size Specify the maximum file size allowed. Some users may need to stitch the video clips together when searching and packing up forensic evidence. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Video_20200113_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Media type - System log Select to send a system log when a trigger is activated.
VIVOTEK In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action. When completed, click the Save event button to enable the settings and click Close to exit Event Settings page. The new Event / Server settings / Media will appear in the event drop-down list on the Event setting page.
VIVOTEK Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scripts has reached the limit, an alert message will prompt. If you need more information, please contact VIVOTEK technical support.
VIVOTEK Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of 5 motion detection windows can be configured. Motion Detection Setting 2: For special situations 1 Motion Detection Setting 1: For normal situations 2 Follow the steps below to enable motion detection: 1. Click New to add a new motion detection window. 2. In the Window Name text box, enter a name for the motion detection window.
VIVOTEK Photos or videos can be captured instantly and configured to be sent to a remote server (via an Email or FTP server). For more information on how to configure an event setting, please refer to Event settings on page 122. A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the preset threshold. Larger than the min.
VIVOTEK This motion detection window will also be displayed on the Event Settings page. You can go to Event > Event settings > Trigger to select it as a trigger source. Please refer to page 123 for detailed informatio. NOTE: ► How does motion detection work? A C Min. item size Alerted pixels < Min. item size B D Min. item size Alerted pixels > Min. item size There are two motion detection parameters: Sensitivity and Min. Item Size.
VIVOTEK Applications > DI and DO Digital input: Select High or Low as the Normal status for the digital input. Connect the digital input pin of the Network Camera to an external device to detect the current connection status. Digital output: Select Grounded or Open to define the normal status for the digital output. Connect the digital output pin of the Network Camera to an external device to determine the current status. Set up the event source as DI on Event > Event settings > Trigger.
VIVOTEK Applications > Tampering detection This section explains how to set up camera tamper detection. With tamper detection, the camera is capable of detecting incidents such as redirection, blocking or defocusing, or even spray paint. Please follow the steps below to set up the camera tamper detection function: 1. Click to select the checkbox before tampering conditions: Tampering detection, Image too dark, Image too bright, and Image too blurry. Enter the tamper trigger duration. (10 sec. ~ 10 min.
VIVOTEK Applications > Audio detection Audio detection, along with video motion detection, is applicable in the following scenarios: 1. Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a door/window. 2. A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of machines. 3. A PTZ camera can be directed to turn to a preset point by the occurrence of audio events. 4.
VIVOTEK You can use the Profile window to configure a different Audio detection setting. For example, a place can be noisy in the day time and become very quiet in the night. 1. Click on the Enable this profile checkbox. Once the Audio detection window is opened, the current sound input will be interactively indicated by a fluctuating yellow wave diagram. 2. Use a mouse click to drag the Alarm level tab to a preferred location on the slide bar. 3. Select the Day, Night, or Schedule mode check circles.
VIVOTEK Applications > Shock detection The camera comes with a shock accelerometer. The shock sensor can detect impacts to the camera. For example, when a person deliberately tries to destroy the camera, the camera can report the event to the administrator. Normally, a 5kgm impact can cause the detected impact level to surge to 50% on the scale. Configure the Alarm Level to a preferred percentage on the chart. Click the Enable shock detector checkbox and click Save to complete the configuration.
VIVOTEK Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) Users can store and execute VIVOTEK's or 3rd-party software modules onto the camera's flash memory or SD card. These software modules can apply in video analysis for intelligent video applications such as license plate recognition, object counting, or as an agent for edge recording, etc. • Once the software package is successfully uploaded, the module configuration (vadp. xml) information is displayed.
VIVOTEK To start a module, select the checkcircle in front, and click the Start button. If you should need to remove a module, select the checkcircle in front and then click the Stop button. By then the module status will become OFF, and the X button will appear at the end of the row. Click on the X button to remove an existing module. When prompted by a confirm message, Click Yes to proceed.
VIVOTEK On the License page, register and activate the license for using VIVOTEK's VADP modules. You should acquire the license key elsewhere, and manually upload to the network camera. Follow the onscreen instruction on VIVOTEK's website for the registration procedure.
VIVOTEK Recording > Recording settings This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE: ► Please remember to format your SD card via the camera’s web console (in the Local storage . SD card management page) when using it for the first time. Please refer to page 153 for detailed information. Recording Settings Click Add to open the recording setting window.
VIVOTEK If you enable adaptive recording on a camera, only when an event is triggered on Camera A will the server record the full frame rate streaming data; otherwise, it will only request the I frame data during normal monitoring, thus effectively saves bandwidths and storage space. NOTE: ► To enable adaptive recording, please make sure you’ve set up the trigger source such as Motion Detection, DI Device, or Manual Trigger.
VIVOTEK 2. Destination You can select the SD card or network storage (NAS) for the recorded video files. If you have not configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1. Fill in the information for your server. For example: 3 Network storage path (\\server name or IP address\folder name) 1 2 4 User name and password for your server 2. Click Test to check the setting.
VIVOTEK If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: You can choose either the entire free space available or limit the reserved space. The recording size limitation must be larger than the reserved amount for cyclic recording.
VIVOTEK If you want to enable recording notification, please click Event to configure event triggering settings. Please refer to Event > Event settings on page 122 for more details. When completed, select Enable this recording. Click Save to enable the setting and click Close to exit this page. When the system begins recording, it will send the recorded files to the network storage. The new recording name will appear in the drop-down list on the recording page as shown below.
VIVOTEK Storage > Storage management NOTE: • • • • • It is recommended to turn OFF the recording activity before you remove an SD card from the camera. The lifespan of an SD card is limited. Regular replacement of the SD card can be necessary. Camera filesystem takes up several megabytes of memory space. The storage space cannot be used for recording. Using an SD card that already contains data recorded by another device should not be used in this camera.
VIVOTEK SD card control ■ Minimum reserved storage space: The reserved space can be used as a customized turn-around space when the storage is about to be full and needs to delete old recordings. ■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you wish to retain a file.
VIVOTEK NAS control ■ Minimum reserved storage space: This can be used to configure the percentage of space threshold for the camera commencing space clean-ups. The minimum reserved space is 512MB for SD card; 1GB for a network share. ■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum capacity is reached, the oldest file will be overwritten by the latest one.
VIVOTEK Storage > Content management This section explains how to manage the content of recorded videos on the Network Camera. Here you can search and view the records and view the searched results. Searching and Viewing the Records This column allows the user to set up search criteria for recorded data. If you do not select any criteria and click Search button, all recorded data will be listed in the Search Results column. ■ File attributes: Select one or more items as your search criteria.
VIVOTEK Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction. Numbers of entries displayed on one page Click to open a live view ■ Play: Click on a search result which will highlight the selected item. A Play window will appear on top for immediate review of the selected file.
VIVOTEK ■ Lock/Unlock: Select the checkbox in front of a desired search result, then click this button. The selected items will become Locked, which will not be deleted during cyclic recording. You can click again to unlock the selections. For example: Click to switch pages ■ Remove: Select the desired search results, then click this button to delete the files.
VIVOTEK Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application programming interface. The HTTP-based camera interface provides the functionality to request a single image, control camera functions (PTZ, output relay etc.), and get and set internal parameter values.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory. The file extension .cgi is required.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 4. Security Level SECURITY LEVEL SUB-DIRECTORY DESCRIPTION 0 anonymous Unprotected. 1 [view] viewer Can view, listen, and talk to camera. 4 [operator] operator Operator access rights can modify most of the camera’s parameters except some privileges and network options. 6 [admin] admin Administrator access rights can fully control the camera’s operations. 7 N/A Internal APIs. Unable to be changed by any external interfaces.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/getparam.cgi?[] [&…] http:///cgi-bin/viewer/getparam.cgi?[] [&…] http:///cgi-bin/operator/getparam.cgi?[] [&…] http:///cgi-bin/admin/getparam.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n 29 User's Manual - 163
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/setparam.cgi? = [&=…][&return=] http:///cgi-bin/viewer/setparam.cgi? = [&=…][&return=] http:///cgi-bin/operator/setparam.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK [] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n 31 User's Manual - 165
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7. Available Parameters on the Server Valid values: VALID VALUES DESCRIPTION string[] Text strings shorter than ‘n’ characters. The characters “,’,<,>,& are invalid. string[n~m] Text strings longer than `n’ characters and shorter than `m’ characters. The characters “,’,<,>,& are invalid. password[] The same as string but displays‘*’ instead. Any single integer number in 32-bits. The range is -2147483648~2147483647.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved VALID VALUES DESCRIPTION The format for resolution. W is the pixel number of width. H is the pixel number of height. Ex: 1920x1080, 2048x1536 available The API is listed in product WebAPIs. non-available The API is not in product WebAPIs. valid The API is listed in product WebAPIs, and is functional. non-valid The API is listed in product WebAPIs, but is malfunction in this status.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) timezoneindex -489 ~ 529 6/6 Indicate timezone and area.
© 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY VIVOTEK DESCRIPTION (get/set) 120: GMT 03:00 Baghdad, Kuwait, Riyadh, Moscow, St.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) daylight_auto_begintim string[19] e 6/7 Display the current daylight saving start time. daylight_auto_endtime string[19] 6/7 Display the current daylight saving end time. daylight_timezones string 6/6 List time zone index which support daylight saving time. updateinterval 0, 3600, 6/6 0 to Disable automatic time adjustment, otherwise, it indicates the seconds between NTP automatic update intervals.
© 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY VIVOTEK DESCRIPTION (get/set) restoreexceptvadp 0, values except the custom language file the user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands. When cooperating with others, the system parameters will be restored to the default value except for a union of the combined results.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Only available when "capability_image_c<0~(n-1)>_lensconfig uration_support" != 0. 7.1.1 System.Info Subgroup of system: info (The fields in this group are unchangeable.) NAME VALUE SECURITY DESCRIPTION (get/set) modelname string[40] 0/7 Internal model name of the server extendedmodelname string[40] 0/7 ODM specific model name of server (eg. DCS-5610).
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) language_i7 : 简体中文 language_i8 : 繁體中文 customlanguage_max count 0, 0/6 Maximum number of custom languages supported on the server. customlanguage_coun 0, 0/6 Number of custom languages which have been uploaded to the server. customlanguage_i<0~ (maxcount-1)> 0/6 Custom language name. string 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.2.1 Status per Channel Group: status_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) signal_detect 1/7 Indicates whether the video source is connected or not. * Only available when capability_videoin_type is 0 or 1. signal_type ntsc,pal 1/7 The actual modulation type. * Only available when capability_videoin_type is 0 or 1. 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.5 Security 1.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.6 Network Group: network NAME VALUE SECURITY (get/set) DESCRIPTION preprocess 6/6 An 32-bit integer, each bit can be set separately as follows: Bit 0 => HTTP service; Bit 1=> HTTPS service; Bit 2=> FTP service; Bit 3 => Two way audio and RTSP Streaming service; To stop service before changing its port settings. It’s recommended to set this parameter when change a service port to the port occupied by another service currently.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) 0 => Use preset ipaddress, subnet, rounter, dns1, and dns2. ipaddress 6/6 IP address of server. subnet 6/6 Subnet mask. router 6/6 Default gateway. dns1 6/6 Primary DNS server. dns2 6/6 Secondary DNS server. wins1 6/6 Primary WINS server. wins2 6/6 Secondary WINS server. 7.6.1 802.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.6.2 QOS Subgroup of network: qos_cos (capability_protocol_qos_cos > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable/disable CoS (IEEE 802.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 7.6.4 FTP Subgroup of network: ftp NAME VALUE SECURITY DESCRIPTION (get/set) port 21, 1025~65535 6/6 Local ftp server port. enable 6/6 Enable ftp. 7.6.5 HTTP Subgroup of network: http NAME VALUE SECURITY (get/set) DESCRIPTION port 80, 1025 ~ 65535 1/6 HTTP port. alternateport 1025~65535 6/6 Alternate HTTP port. authmode basic, digest 1/6 HTTP authentication mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) is equal or greater than 0311c. anonymousviewing 1/6 Enable anonymous streaming viewing. 7.6.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.6.8 RTSP Subgroup of network: rtsp (capability_protocol_rtsp > 0) NAME VALUE SECURITY (get/set) DESCRIPTION port 554, 1025 ~ 65535 1/6 RTSP port. (capability_protocol_rtsp=1) anonymousviewing 1/6 Enable anoymous streaming viewing. authmode disable, 1/6 RTSP authentication mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.6.9 RTSP Multicast Subgroup of network_rtsp_s<0~(n-1)>_multicast n denotes the value of "capability_nmediastream * capability_nvideoin" NAME VALUE SECURITY (get/set) DESCRIPTION alwaysmulticast 4/4 Enable always multicast. ipaddress 4/4 Multicast video IP address. * We replace "network_rtsp_s<0~(n-1)>_multicast_ipaddress" with " network_rtsp_s<0~(n-1)>_multicast_videoipadd ress ".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.6.10 SIP Port Subgroup of network: sip (capability_protocol_sip> 0) NAME VALUE SECURITY DESCRIPTION (get/set) port 1025 ~ 65535 1/6 SIP port. 7.6.11 RTP Port Subgroup of network: rtp NAME VALUE SECURITY (get/set) DESCRIPTION videoport 1025 ~ 65535 6/6 Video channel port for RTP. audioport 1025 ~ 65535 6/6 Audio channel port for RTP. metadataport 1025 ~ 65535 6/6 Metadata channel port for RTP. 7.6.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) or greater than 0312a. 7.7 IP Filter Group: ipfilter NAME VALUE SECURITY (get/set) DESCRIPTION enable 6/6 Enable access list filtering. admin_enable 6/6 Enable administrator IP address. admin_ip string[43] 6/6 Administrator IP address. maxconnection 1~ 6/6 "capability_protoc ol_maxconnection" Maximum number of (s).
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.8 Video Input Group: videoin NAME VALUE SECURITY (get/set) DESCRIPTION cmosfreq 50, 60 4/4 CMOS frequency. * Only available when capability_videoin_type is 2. whitebalance auto, 4/4 Modes of white balance. panorama, manual, rbgain, widerange, outdoor, indoor, sodiumauto, etc "auto": Auto white balance "panorama": indicates that camera would try to balance the white balance effect of every sensor.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) from DC's exposure tuning options. The definition is: 0: EV -2.0 1: EV -1.7 2: EV -1.3 3: EV -1.0 4: EV -0.7 5: EV -0.3 6: EV 0 7: EV +0.3 8: EV +0.7 9: EV +1.0 10: EV +1.3 11: EV +1.7 12: EV +2.0 * Only available when "capability_image_c<0~(n-1)>_exposu re_mode" !=0 irismode fixed, indoor, outdoor 4/4 Control DC-Iris mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) switch on/off BLC. color 0, 1 4/4 0 =>monochrome 1 => color * Only available when " capability_videoin_c<0~(n-1)>_color_ support" is 1. flip 4/4 Flip the image. mirror 4/4 Mirror the image. rotate 0,90,180,270 1/4 The rotation angle of image. Support only in Rotation mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) etc. 5~8000 => 1/5s ~ 1/8000s etc. * Only available when "capability_image_c<0~(n-1)>_exposu re_minrange" != "-" * Only valid when "piris_mode"=manual or "irismode"=fixed * Only available when * Available value is listed in "capability_image_ c<0~(n-1)>_exposu re_minrange" "capability_image_c<0~(n-1)>_exposu re_rangetype" is "twovalues".
VIVOTEK © 2019 VIVOTEK INC.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.8.1 Video Input Setting per Channel Group: videoin_c<0~(n-1)> for n channel products, and m is stream number n denotes the value of "capability_nvideoin", m denotes the value of "capability_nmediastream" NAME VALUE SECURITY( get/set) DESCRIPTION cmosfreq 50, 60 4/4 CMOS frequency. * Only available when " capability_videoin_type " is 2 mode 0~ 4/4 Indicate the video mode on use. 4/4 Modes of white balance.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) de" !="-" rgain 0~100 4/4 Manual set rgain value of gain control setting. 0: Weak <-> 100: Strong * Only available when "rbgain" is listed in "capability_image_c<0~(n-1)>_wbmo de". * Only valid when "videoin_c<0~(n-1)>_whitebalance" ! = auto * Normalized range. bgain 0~100 4/4 Manual set bgain value of gain control setting.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) 9: EV +1.0 10: EV +1.3 11: EV +1.7 12: EV +2.0 * Only available when "capability_image_c<0~(n-1)>_exposu re_mode" !=0 exposuremode irispriority, qualitypriority, manual, 4/4 Select exposure mode. "auto": Automatically adjust the Iris, Gain and Shutter Speed to fit the exposure level.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) * Only available when "capability_image_c<0~(n-1)>_iristype "=dciris piris_mode manual, indoor, outdoor,- 1/4 Control P-Iris mode. "outdoor": Auto-setting P-Iris to get best quality, but easy to meet rolling or flicker effect in indoor environment. "indoor": Avoid rolling and flicker effect first. "manual": Manual set P-Iris by "piris_position". "-": not support.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) 0: Low <-> 100: High * Only available when "capability_image_c<0~(n-1)>_agc_m axgain" != "-" * Only valid when "piris_mode"=manual or "irismode"=fixed * Normalized range. * Only available when "capability_image_c<0~(n-1)>_exposu re_rangetype" is "twovalues". mingain 0~100 4/4 Minimum gain value.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) * Only available when " capability_videoin_c<0~(n-1)>_color_ support" is 1. flip 4/4 Flip the image. mirror 4/4 Mirror the image. rotate 0,90,180,270 1/4 The rotation angle of image.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) ploadfilename name uploaded by user minexposure <1~32000>, <5~32000>, <1~8000>, <5~8000>, etc. 4/4 * Available value is listed in Minimum exposure time 1~32000 => 1s ~ 1/32000s 5~32000 => 1/5s ~ 1/32000s 1~8000 => 1s ~ 1/8000s 5~8000 => 1/5s ~ 1/8000s etc.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) "capability_image_c<0~(n-1)>_exposu re_rangetype" is "twovalues". shuttervalue * Available value is listed Exposure time 1~32000 => 1s ~ 1/32000s 5~32000 => 1/5s ~ 1/32000s 1~8000 => 1s ~ 1/8000s 5~8000 => 1/5s ~ 1/8000s etc. * This parameter may also restrict in "capability_image_c<0~(n1)>_exposure_maxrange" image frame rate from sensor due to sensor generates a frame per exposure time.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) * We support this parameter when the version number (httpversion) is equal or greater than 0311a. crop_position (x,y) 1/7 Crop left-top corner coordinate. crop_size (WxH) 1/7 Crop width and height. (width must be 16x or 32x and height must be 8x) zoomratiodispl ay 1/4 Indicates multiple of zoom in is “on-screen display” or not.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) solution "capability_videoin_c<0~( n-1)>_resolution". Besides, available options is referred to "capability_videoin_c<0~( n-1)>_maxresolution" and "capability_videoin_c<0~( n-1)>_minresolution" s<0~(m-1)>_s martfps_enabl e 4/4 Enable "Smart fps" function. * Only available when "capability_videoin_c<0~(n-1)>_smart fps_support" is 1.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) "qpercent" 99: Use the quality level in "qvalue" * Only valid when "h264_ratecontrolmode"= vbr. s<0~(m-1)>_h2 0~51 64_qvalue 4/4 Manual video quality level input. The Q value which is used by encoded library directly. * Only valid when "h264_ratecontrolmode"= vbr and s<0~(m-1)>_h264_quant = 99. s<0~(m-1)>_h2 1~100 64_qpercent 4/4 Select customized quality in a normalized full range.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) nt 1: Worst quality 100: Best quality * Only valid when "h264_ratecontrolmode"= cbr and "quant"= 100. s<0~(m-1)>_h2 20000~"capability_videoin 64_bitrate _c<0~(n-1)>_h264_maxbit rate" 4/4 The target bit rate in constant bit rate mode.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) equal or greater than 0301c. s<0~(m-1)>_h2 250, 500, 1000, 2000, 65_intraperiod 3000, 4000 4/4 The time interval between two I-frames (Intra coded picture). The unit is millisecond (ms). * Only available when h265 is listed in "capability_videoin_codec". s<0~(m-1)>_h2 cbr, vbr 65_ratecontrol mode 4/4 cbr: Constant bit rate mode. vbr: Fixed quality mode, all frames are encoded in the same quality.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) "capability_videoin_codec". * Only valid when "h265_ratecontrolmode"= vbr and "quant"= 100. s<0~(m-1)>_h2 20000~"capability_videoin 65_maxvbrbitr _c<0~(n-1)>_h265_maxbit ate rate" 4/4 The maximum allowed bit rate in fixed quality mode. When the bit rate exceeds this value, frames will be dropped to restrict the bit rate. * Only available when h265 is listed in "capability_videoin_codec".
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) 65_bitrate _c<0~(n-1)>_h265_maxbit rate" s<0~(m-1)>_h2 framerate,imagequality 65_prioritypoli cy mode. * Only available when h265 is listed in "capability_videoin_codec". * Only valid when "h265_ratecontrolmode"= cbr 4/4 Set prioritypolicy * Only available when h265 is listed in "capability_videoin_codec".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) peg_quant 99, 100 "mjpeg_ratecontrolmode"= vbr.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) "mjpeg_ratecontrolmode"= vbr s<0~(m-1)>_mj 1~5, 100 peg_cbr_quant 4/4 Set the pre-defined quality level: 1: Medium 2: Standard 3: Good 4: Detailed 5: Excellent 100: Use the quality level in "cbr_qpercent" * Only valid when "mjpeg_ratecontrolmode"= cbr. s<0~(m-1)>_mj 1~100 peg_cbr_qperc ent 4/4 Select customized quality in a normalized full range.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) CIF(352x288)->(384x288) For NTSC: D1/4CIF(720/704x480) -> (640x480) CIF(352x240)->(320x240) * Only available when capability_videoin_type is 0 or 1. wdrpro_mode 0, 1, 2 4/4 0: Disable WDR Pro. 1: Enable WDR Pro. * Only valid when "capability_image_c<0~(n-1)>_wdrpro _mode" = 1 2: Enable WDR Pro II.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY( DESCRIPTION get/set) d" is 1 aespeed_spee dlevel 1~100 4/4 The speed level of AE converge speed. 1~20: level 1 21~40: level 2 41~60: level 3 61~80: level 4 81~100: level 5 Level 1~4(low ~ high) The higher speed level meas shorter AE converged time during AE executing.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY( DESCRIPTION get/set) "capability_videoin_c<0~(n-1)>_moun ttype" != "-". enablewaterm ark 0, 1 1/6 0: Not to add watermarks on images 1: Add watermarks on images * Only available when "capability_fisheye" > 0 s<0~(m-2)>_fis heyedewarpm ode ‘1O, 1P, 2P, 1R, 4R’ for ceiling/floor mount 1/4 Local dewarp mode. “1O” is original mode (disable).
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) ual" is 1. "hybrid": only available when "capability_smartstream_mode_hybri d" is 1. qualitypriority -5,-4,-3,-2,-1,1,2,3,4,5 4/4 The differential value of Q between the regions of interest (ROI) and the areas of non-interest (non-ROI) of the display image. If the value is a positive number, the video quality of ROI is better than the non-ROI areas. The level is from 1 to 5.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.8.1.1 Alternative Video Input Profiles per Channel In addition to the primary setting of video input, there can be alternative profile video input setting for each channel which might be for different scene of light (daytime or nighttime).
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) etc. * This parameter may also restrict image frame rate from sensor due to sensor generates a frame per exposure time. Ex: If this is set to 1/5s ~ 1/8000s and camera takes 1/5s on the night, then sensor only outputs 5 frame/s.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) the version number (httpversion) is equal or greater than 0302a. enableblc 4/4 Enable backlight compensation. * Not support this parameter anymore when the version number (httpversion) is equal or greater than 0301a. * It's recommanded to use "exposurewin_c_mode" to switch on/off BLC.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) adjusting Iris, Gain automatically. "irispriority": Manually adjust with variable Iris, and keep adjusting Gain and Shutter speed automatically. "qualitypriority": Automatically adjust the Iris, Gain and Shutter Speed by VIVOTEK quality algorithm. "manual": Manually adjust with variable Shutter, Iris and Gain.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) specifically for indoor. "sodiumauto": sodium vapor lamps. * Only available when "capability_image_c<0~(n-1)>_wbmo de" !="-" rgain 0~100 4/4 Manual set rgain value of gain control setting. 0: Weak <-> 100: Strong * Only available when "rbgain" is listed in "capability_image_c<0~(n-1)>_wbmo de". * Only valid when "videoin_c<0~(n-1)>_whitebalance" ! = auto * Normalized range.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) * Only available when "capability_image_c<0~(n-1)>_exposu re_rangetype" is "twovalues". mingain 0~100 4/4 Minimum gain value. 0: Low <-> 100: High * Only available when "capability_image_c<0~(n-1)>_agc_mi ngain" != "-" * Only valid when "piris_mode"=manual or "irismode"=fixed * Normalized range. * Only available when "capability_image_c<0~(n-1)>_exposu re_rangetype" is "twovalues".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) piris_mode manual, indoor, outdoor,- 1/4 Control P-Iris mode. "outdoor": Auto-setting P-Iris to get best quality, but easy to meet rolling or flicker effect in indoor environment. "indoor": Avoid rolling and flicker effect first. "manual": Manual set P-Iris by "piris_position".
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) wdrpro_streng 1: Enable WDR Pro. * Only valid when "capability_image_c<0~(n-1)>_wdrpro _mode" = 1 2: Enable WDR Pro II. * Only valid when "capability_image_c<0~(n-1)>_wdrpro _mode" = 2 1~100 4/4 The strength of WDR Pro. The bigger value means the stronger strength of WDR Pro.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) Level 1~4(low ~ high) The higher speed level meas shorter AE converged time during AE executing. * Only available when "capability_image_c<0~(n-1)>_aespee d" is 1 aespeed_sensi tivity 1~100 4/4 The sensitivity of AE converge speed.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.9 Time Shift Settings Group: timeshift for n channel products and m stream n denotes the value of "capability_nvideoin", m denotes the value of "capability_nmediastream" (capability_timeshift > 0) NAME VALUE SECURITY (get/set) DESCRIPTION enable 4/4 Enable time shift streaming. * We replace this parameter with " timeshift_c<0~(n-1)>_enable" when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) 0312a. disableirled 6/6 Enable/disable built-in IR led * Only available when "capability_daynight_illuminators_buil tin_support > 0" and irled is listed in "capability_daynight_ illuminators _builtin_type" * We replace this parameter with "ircutcontrol_illuminators_builtin_irle d_enabled" when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) blackwhitemode" is 1. * We replace this parameter with “ircutcontrol_c<0~(n-1)>_bwmode” when the version number (httpversion) is equal or greater than 0312a. sensitivity
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.10.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved * Only available when "capability_daynight_c<0~(n-1)>_ blackwhitemode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0312a. sensitivity low,normal,high,1 ~100 6/6 Sensitivity of day/night control.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved equal or greater than 0312a. builtin_whiteled_enable d 6/6 Enable/disable built-in white led * Only available when "capability_daynight_illuminators_buil tin_support > 0" and "whiteled" is listed in "capability_daynight_ illuminators _builtin_type" * We support this parameter when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved blueenhanced equal or greater than 0312a. * Available values are listed in "capability_daynig ht_illuminators _spectrum_mode" . * Only available when "capability_daynight_illuminators_ spectrum _support > 0". 7.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) is equal or greater than 0400a. saturation -5~5,100 4/4 -5: Less saturation <-> 5: More saturation 100: Use " image_c_saturationpercent" * Only available when bit 2 of "capability_image_c<0~(n-1)>_basicse tting" is 1. * We replace "saturation" with "saturationpercent". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) saturationpercent 0~100 4/4 Set saturation in the normalized range. 0: Less saturation <-> 100: More saturation * Only available when bit 2 of "capability_image_c<0~(n-1)>_basicse tting" is 1. sharpnesspercent 0~100 4/4 Set sharpness in the normalized range.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) 1 dnr_mode 4/4 3D noise reduction. 0:disable 1:enable * Only available when "capability_image_c<0~(n-1)>_dnr" is 1 dnr_strength _dnr" is 1 dependent> defog_mode 4/4 Enable/disable defog mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) e". dis_strength 1~100 4/4 Strength of digital image stabilizer * Only available when 'dis' is listed in "capability_image_c<0~(n-1)>_is_mod e".
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) Spatical mode provides the best image quality, while Blend mode provides better image quality (than not using the deinterlace function at all). * Only available when "capability_image_c<0~(n-1)>_deinter lace_support" is 1. xoffset 0~100 4/4 Adjusting the image to proper position horizontally. * Only available when the bit 4 of capability_image_c<0~(n-1)>_basicset ting is 1.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) (httpversion) is equal or greater than 0310a. profile_i<0~(m-1)> _enable 4/4 Enable/disable this profile setting profile_i<0~(m-1)> _policy night, schedule 4/4 The mode which the profile is applied to. * Not support "policy=day" anymore when the version number (httpversion) is equal or greater than 0301a. profile_i<0~(m-1)> _begintime hh:mm 4/4 Begin time of schedule mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * We replace "profile_i0_contrast" with "profile_i0_contrastpercent ". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Only available when bit 0 of "capability_image_c<0~(n-1)>_basicse tting" is 1. profile_i<0~(m-1)> _contrastpercent 0~100 4/4 Set contrast in the normalized range. 0: Less contrast <-> 100: More contrast * Only available when bit 1 of "capability_image_c<0~(n-1)>_basicse tting" is 1 profile_i<0~(m-1)> _saturationpercent 0~100 4/4 Set saturation in the normalized range.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "capability_image_c<0~(n-1)>_gamm acurve" is 1 profile_i<0~(m-1)> _lowlightmode 4/4 Enable/disable low light mode. * Only available when "capability_image_c<0~(n-1)>_lowligh tmode" is 1 profile_i<0~(m-1)> _hlm 4/4 Enable/disable hightlight mask.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) profile_i<0~(m-1)> _eis_strength 1~100 4/4 Strength of electronic image stabilizer * Only available when 'eis' is listed in "capability_image_c<0~(n-1)>_is_mod e". profile_i<0~(m-1)> _dis_mode 4/4 Digital image stabilizer 0:disable 1:enable * Only available when 'dis' is listed in "capability_image_c<0~(n-1)>_is_mod e".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.12 Exposure Window Setting per Channel Group: exposurewin_c<0~(n-1)> for n channel profucts n denotes the value of "capability_nvideoin" (Only available when "capability_image_c<0~(n-1)>_exposure_mode"=1) NAME VALUE SECURITY (get/set) DESCRIPTION mode auto, custom,blc,hlc,center 4/4 "auto": Use full image view as the only exposure window. * Available values are listed "custom": Use custom windows.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) window. * Only available when qvga is listed in "capability_image_c<0~(n-1)>_exposu re_windomain". size <0~320x0~240> 4/4 Width and height of the window. * Only available when qvga is listed in "capability_image_c<0~(n-1)>_exposu re_windomain".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved (Only available when "capability_image_c<0~(n-1)>_exposure_mode"=1) NAME VALUE SECURITY (get/set) DESCRIPTION mode auto, custom,blc,hlc,center * Available values are listed in "capability_image_c<0~(n-1) >_exposure_winmode" 4/4 The mode indicates how to decide the exposure. "auto": Use full view as the only one exposure window. "custom": Use inclusive and exclusive window.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Only available when qvga is listed in "capability_image_c<0~(n-1)>_exposu re_windomain". size <0~320x0~240> 4/4 Width and height of the window. * Only available when qvga is listed in "capability_image_c<0~(n-1)>_exposu re_windomain". homepx <0~W,0~H> 4/4 W: 0~ The current image width -1 H: 0~ The current image height -1 sizepx <0~Wx0~ H> Left-top corner coordinate of the window.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.13 Audio Input per Channel Group: audioin_c<0~(n-1)> (capability_naudioin>0) n denotes the value of "capability_naudioin" NAME VALUE SECURITY (get/set) DESCRIPTION source micin, linein 4/4 micin => use built-in microphone input. linein => use external microphone input. * Reserved for compatibility, and suggest don't use this since the version number (httpversion) is equal or greater than 0301a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) volume_external 0~100 4/4 Volume when take external microphone as input source. 0: Minimum 100: Maximum * Only available when the channel supports external microphone (The related bit of "capability_audio_extmic" is equal to 1). mute 0, 1 1/4 0: Mute off 1: Mute on gain 0~100 4/4 Gain of input.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) description of "volume_internal" and "volume_external". s0_codectype aac4, gamr, g711, g726 (Available codec are listed in "capability_audioin_ codec") 4/4 Set audio codec type for input. aac4: Advanced Audio Coding (AAC) gamr: Adaptive Multi-Rate (AMR) g711: G.711 g726: G.726 s0_aac4_bitrate 16000, 4/4 Set AAC4 bitrate in bps. * Only available if AAC is supported.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) s0_g726_vlcmode 0, 1 4/4 Enable vlcmode for G.726. 0: Standard mode. 1: Solve compatibility problem with VLC player. * Only available if G.726 is supported. aec_enable 4/4 Enable acoustic echo cancellation. * Only available when "capability_audio_aecmode" is "manual". * We support this parameter when the version number (httpversion) is equal or greater than 0306b.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.15 Play an Audio Clip Group: audioclip_i<0~1> (capability_audio_audioclip=1) NAME VALUE SECURITY (get/set) DESCRIPTION name string[40] 1/4 Specify the audio clip name that can be played when an event occurs. size 0, 1/4 The size of audio clip.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999 position. (4 points: x0,y0,x1,y1,x2,y2,x3,y3) * Only available when "capability_motion_wintype" = polygon. * Only available when std is listed in "capability_motion_windomain" objsize 1 ~ 100 4/4 Percent of motion detection window. sensitivity 0 ~ 100 4/4 Sensitivity of motion detection window.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) the version number (httpversion) is equal or greater than 0400a. left 0 ~ 320 4/4 Left coordinate of window position. * Only available when "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Only available when qvga is listed in "capability_motion_windomain". * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) name string[14] 4/4 Name of motion window. polygonstd 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999 4/4 Coordinate of polygon window position. (4 points: x0,y0,x1,y1,x2,y2,x3,y3) * Only available when "capability_motion_wintype" = polygon. * Only available when std is listed in "capability_motion_windomain objsize 1 ~ 100 4/4 Percent of motion detection window.
© 2019 VIVOTEK INC. All Right Reserved NAME VALUE VIVOTEK SECURITY DESCRIPTION (get/set) to use this> "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain". * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. top 0 ~ 240 4/4 Top coordinate of window position. * Only available when "capability_motion_wintype" = rectangle.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) the version number (httpversion) is equal or greater than 0400a. 7.17 Tampering Detection Settings Group: tampering_c<0~(n-1)> for n channel products (capability_tampering > 0) n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable or disable tamper detection. threshold 0~100 4/4 Threshold of tamper detection.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) blurry_duration 1~10 4/4 If image too blurry value exceeds the "threshold" for more than "duration" second(s), then image too blurry detection is triggered. SECURITY DESCRIPTION 7.18 DDNS Group: ddns (capability_protocol_ddns > 0) NAME VALUE (get/set) enable 6/6 Enable or disable the dynamic DNS. provider DyndnsDynamic, DyndnsCustom, Safe100 6/6 DyndnsDynamic => dyndns.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.20 UPnP Presentation Group: upnppresentation NAME VALUE SECURITY (get/set) DESCRIPTION enable 6/6 Enable or disable the UPnP presentation service. 7.21 UPnP Port Forwarding Group: upnpportforwarding NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the UPnP port forwarding service. upnpnatstatus 0~3 6/7 The status of UPnP port forwarding, used internally.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) 7: LOG_DEBUG setparamlevel 0~2 6/6 Show log of parameter setting. 0: disable 1: Show log of parameter setting set from external. 2. Show log of parameter setting set from external and internal. SECURITY DESCRIPTION 7.23 SNMP Group: snmp (capability_protocol_snmp > 0) NAME VALUE (get/set) v2 6/6 SNMP v2 enabled. 0 for disable, 1 for enable v3 6/6 SNMP v3 enabled.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.24 Layout Configuration Group: layout NAME VALUE SECURITY (get/set) DESCRIPTION logo_default 1/6 0 => Custom logo 1 => Default logo logo_link string[128] http://www.vivot ek.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.25 Privacy Mask Group: privacymask_c<0~(n-1)> for n channel products and m privacy mask window. n denotes the value of "capability_nvideoin" and m denotes the value of "capability_videoin_c<0~(n-1)>_nprivacymask" NAME VALUE SECURITY (get/set) DESCRIPTION enable 4/4 Enable privacy mask. win_i<0~(m-1)>_enable 4/4 Enable privacy mask window. win_i<0~(m-1)>_name string[14] 4/4 Name of the privacy mask window.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) npx 0 ~ W,0 ~ H, 0 ~ W,0 ~ H, 0 ~ W,0 ~ H W: 0~ The current image width -1 H: 0~ The current image height -1 win_i<0~(m-1)>_polygo 0 ~ 9999,0 ~ nstd 9999, 0 ~ 9999,0 ~ 9999, 0 ~ 9999,0 ~ 9999, 0 position. (4 points: x0,y0,x1,y1,x2,y2,x3,y3) * Only available when "capability_image_c<0~(n-1)>_privacy mask_wintype" = polygon.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) >_maxpan" "capability_camctrl_c<0~(n-1)>_ buildinpt" is "1" win_i<0~(m-1)>_tilt "capability_ptz_c<0~(n-1) 4/4 >_mintilt" ~ "capability_ptz_c<0~(n-1) >_maxtilt" Tilt position of window position. * Only available when bit1 of "capability_camctrl_c<0~(n-1)>_ buildinpt" is "1" win_i<0~(m-1)>_zoom "capability_ptz_c<0~(n-1) 4/4 >_minzoom" ~ "capability_ptz_c<0~(n-1) Zoom position of window position.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) change the old features and interfaces. Revision Increase the revision when fix bugs without change any features of the output. _platform This is a constant, it is used to distinguish between different platforms API version format: MMmmr_k Where "MM" is the major version, "mm" is the minor version and "r" is the revision. 'M' and 'm' and 'k' are decimal digit from 0 to 9, while 'r' is an alphabetic.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) capability_daynight_c<0~"capability_ nvideoin"-1>_externalir for external IR) * Not support this parameter anymore when the version number (httpversion) is equal or greater than 0301a. npir 0, 0/7 Number of PIRs. ndi 0, 0/7 Number of digital inputs.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) nmotion 0/7 The number of motion window. nmotionprofile 0, 0/7 Number of motion profiles. nevent 0, 0/7 Number of event. * We support this parameter when the version number (httpversion) is equal or greater than 0311c. nrecording 0, 0/7 Number of recording.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) is supported or SD/PZ/PT/PD/video server series) Bit 6 => (only available when bit0 is 1) Reserved bit; always 0. Bit 7 => (only available when bit0 is 1) External or built-in PT; 0(built-in), 1(external) windowless 0/7 Indicate whether to support windowless plug-in. evctrlchannel 0/7 Indicate whether to support HTTP tunnel for event/control transfer.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) presettourdirection 0/7 Indicate whether to support preset tour direction function. It means users can choose which direction the preset tour goes. * We support this parameter when the version number (httpversion) is equal or greater than 0307a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) channel. For some dual-stream products, both streams support ePTZ. nanystream 0, 0/7 number of any media stream per channel iva 0/7 Indicate whether to support Intelligent Video analysis whitelight 0/7 Indicate whether to support white light led.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "tampering" = Tamper detection. "vi" = Virtual input (Manual trigger) "vadp" = VADP trigger. "di"= Digital input. "volalarm" = Audio detection. "temperature" = Temperature detection. "pir" = PIR detection. "visignal" = Video input signal loss. "backup" = Backing up recorded files. "smartsd" = Lifetime detection of SD card. "shockalarm" = Shock detection. "virestore" = Video input signal restore.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) protocol_rtp_multi cast_scalable 0/7 Indicate whether to support scalable multicast. protocol_rtp_multi cast_backchannel 0/7 Indicate whether to support backchannel multicast. protocol_rtp_tcp 0/7 Indicate whether to support RTP over TCP. protocol_rtp_http 0/7 Indicate whether to support RTP over HTTP.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) xframerate "-" "capability_videoin_c0_mjpeg_maxfra merate". * This is kept for compatibility. videoin_h264_max framerate A list of and "-" 0/7 This equals "capability_videoin_c0_h264_maxfra merate". * This is kept for compatibility. videoin_codec mjpeg, h264, h265 0/7 Available codec of a device, split by comma. The sequence is not limited. EX: FD8183 supports H.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * We support this parameter when the version number (httpversion) is equal or greater than 0306b. audio_aecaffect -, maxframerate:fixed:1 5 0/7 When acoustic echo cancellation function is enabled, some features may become malfunction or be forced to a given value. The affected functions are list here.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) means the max frame rate is 15fps when acoustic echo cancellation function is enabled. "-" means no feature is affected. * Only available when "capability_audio_aec" is "1". * We support this parameter when the version number (httpversion) is equal or greater than 0306b. audio_mic 0/7 Indicate whether to support built-in microphone input.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) audio_lineout 0/7 Indicate whether to support line output. audio_michardwar eswitch 0/7 Indicate whether the hardware supports built-in/external mic switch audio_headphoneo ut 0/7 Indicate whether to support headphone output. * Not support this parameter anymore when the version number (httpversion) is equal or greater than 0301a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) with pixels. "std": A normalized 0~9999 range. "-": Not supported. smartstream_supp ort 0/7 Indicate whether smart stream is supported. smartstream_versi on 0/7 Number of smart stream version. * Only available when "capability_smartstream_support" is 1 smartstream_nstre am 0/7 Number of stream that support smart stream.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "capability_smartstream_support" is 1 smartstream_nwin dow_manual 0/7 Maximum number of tracking window of manual. * Only available when "capability_smartstream_support" is 1 smartstream_nwin dow_hybrid_autotr acking 0/7 Maximum number of tracking window of autotracking in hybrid mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) camctrl_ptztunnel 0/7 Indicate whether to support ptztunnel. * We support this parameter when the version number (httpversion) is equal or greater than 0301b. This equals "capability_camctrl_c0_ptztunnel". * This is kept for compatibility. camctrl_privilege 0/7 Indicate whether to support “Manage Privilege” of PTZ control in the security page. 1: support both /cgi-bin/camctrl/camctrl.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) wireless_s802dot1 1g 0/7 Indicate whether to support wireless 802.11g. wireless_s802dot1 1n 0/7 Indicate whether to support wireless 802.11n. wireless_begincha nnel 1 ~ 14 0/7 Indicate the begin channel of wireless network wireless_endchann el 1 ~ 14 0/7 Indicate the end channel of wireless network wireless_encrypt_ wep 0/7 Indicate whether to support wireless WEP.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) test_ac 0/7 Indicate whether to support test ac key. version_onvifdaem on 0/7 Indicate ONVIF daemon version version_onviftestto ol 0/7 Indicate ONVIF test tool version version_genetec 0/7 Indicate Genetec daemon version * We support this parameter when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * Reserved for compatibility, and suggest don't use this since [httpversion] > 0301a image_focusassist 0/7 Indicate whether to support focus assist. * We replace "capability_image_ focusassist "with "capability_image_c0_ focusassist".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "capability_supportsd" is 1 or "capability_storage_dbenabled" is 1. localstorage_storm grversion localstorage_suppo 0, rtedge 0/7 Indicate storage manager daemon version. * Only available when "capability_supportsd" is 1 or "capability_storage_dbenabled" is 1. 0/7 An 32-bit integer, which indicates the supportive application of edge storage.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) ster auxiliary camera (master side), this value means supporting max number of auxiliary camera. remotecamctrl_sla ve 0/7 Indicate whether to support remote camera control (slave side). fisheyelocaldewarp _c<0~(capability_n videoin)-1> 0/7 Indicate the supported streams of local dewarp. One bit represents one supported stream. The LSB indicates stream 0.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) privilege 0/7 Indicate whether to support “Manage Privilege” of PTZ control in the security page in this video input. 1: support both /cgi-bin/camctrl/camctrl.cgi and /cgi-bin/viewer/camctrl.cgi 0: support only /cgi-bin/viewer/camctrl.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) focusmode auto,onetimeauto,sp 0/7 otlight,manual Focus mode selection: "auto": Camera will automatically adjust the focus position full time to adapt a clear picture. "onetimeauto": Camera will automatically adjust the focus position one time, which follows any PTZ control.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) minpan 0, 0/7 The lower limit for pan position. *Only available when bit0 of "capability_camctrl_c<0~(n-1)>_buildin pt" is "1" maxpan 0, 0/7 The upper limit for pan position. *Only available when bit0 of "capability_camctrl_c<0~(n-1)>_buildin pt" is "1" minpanangle The lower limit for pan angle.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) maxtiltangle 0/7 The upper limit for tilt angle. *Only available when bit1 of "capability_camctrl_c<0~(n-1)>_buildin pt" is "1" zoomspeedlv 0, 0/7 The maximum speed level of zoom motion. *Only available when the value of "capability_camctrl_c<0~(n-1)>_zoomm odule" is "1" minzoom 0, 0/7 The lower limit for zoom position.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Group: capability_daynight_c<0~(n-1)> n denotes the value of "capability_nvideoin" PARAMETER VALUE SECURITY DESCRIPTION (get/set) support 0/7 Indicate whether the camera supports day/night mode switch builtinir 0/7 Indicate whether to support built-in IR led. * We replaced this parameter with “capability_daynight_illuminators_builti n_support” when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) blackwhitemode 0/7 Indicate whether to support automatically switch to Black & White display during the night mode. * We support this parameter when the version number (httpversion) is equal or greater than 0302a. ircutsensitivity_type 0/7 Indicate the cgi interface of "ircutcontrol_sensitivity". "options": the value of "ircutcontrol_sensitivity" parameter is "low, normal,high".
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) extled_interface do 0/7 The device interface of external IR led: "do": digital output * Only available when "capability_daynight_c<0~(n-1)>_extern alir" is 1 * We replaced this parameter with “capability_daynight_illuminators_exter nal_interface” when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) spectrum_mode visible,ir,irenhanced, 0/7 blueenhanced Indicate the spectrum mode. "visible": The ideal default setting for visible light. "ir": The ideal default setting for IR light. "irenhanced": This CCM model increases the brightness effect of IR light. "blueenhanced": This CCM model increases the brightness effect of blue light.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) mode auto,daynight,di,di2, 0/7 di3,di4,schedule, Indicate the day / night switch mode. "auto": The Camera automatically judges the current operation mode by the level of ambient light detected. "daynight": support day mode and night mode. In day mode, the camera streams color video. In night mode, the camera streams black and white video in low light environments.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved builtin_support 0/7 Indicate whether to support built-in led. * We support this parameter when the version number (httpversion) is equal or greater than 0312a. builtin_type irled,whiteled, 0/7 Indicate whether to support built-in led type. "irled": IR led "whiteled": white led "-": not support * We support this parameter when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK spectrum_mode © 2019 VIVOTEK INC. All Right Reserved visible,ir,irenhanced, 0/7 Indicate the spectrum mode. blueenhanced "visible": The ideal default setting for visible light. "ir": The ideal default setting for IR light. "irenhanced": This CCM model increases the brightness effect of IR light. "blueenhanced": This CCM model increases the brightness effect of blue light.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK Group: capability_videoin_c<0~(n-1)> n denotes the value of "capability_nvideoin" PARAMETER VALUE SECURITY (get/set) DESCRIPTION lens_type fisheye, fixed, varifocal, changeable, motor, ics, 0/7 The lens type of this channel. "fisheye": Fisheye lens "fixed": Build-in fixed-focus lens. "varifocal": Build-in varifocal lens. "changeable": changeable lens. Like box-type camera, users can install any C-Mount or CS-Mount lens as they wish.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) rotationaffect 0/7 When rotation is enabled, some features may become malfunction or be forced to a given value. The affected functions are list here. The format is "Affect API name":"Policy":"Description" "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) rotationangle 0/7 The different angles which camera supports for rotation. * Only avaliable when "capability_videoin_c<0~(n-1)>_rotation" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0309b. orientation flip,mirror,rotatio 0/7 Indicates the camera supports flip, mirror or n rotation.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) resolution A list of 0/7 Resolution options in current video mode. These options are the possible options for "videoin_c_s_resolution". The last one is the maximum resolution in current mode. maxresolution A list of 0/7 Represent supported maximum resolution of each stream in current video mode. * The element number is defined as "capability_nmediastream".
© 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY VIVOTEK DESCRIPTION (get/set) mjpeg_maxframerate A list of and "-" Maximum fps that the device can encoded with MJPEG on resolutions in current video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group. * This parameter may be changed when "videoin_c_cmosfreq"=50 or "videoin_c_modulation"=pal.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) h264_maxbitrate 0/7 Maximum bitrates of H.264. The unit is bps. * Only available when 'h264' is listed in "capability_videoin_codec". h264_profile baseline,main,hig 0/7 h Indicate H264 profiles * Only available when 'h264' is listed in "capability_videoin_codec". * We support this parameter when the version number (httpversion) is equal or greater than 0309a.
© 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY VIVOTEK DESCRIPTION (get/set) fisheye_mounttype ceiling, wall, floor 0/7 Indicate the supported type.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) cameraunit_name CU8131, CU8171, CU8161-H, CU8162-H, CU8163-H, CU8361-H, ...,
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) resolutionC1P A list of 0/7 Available resolutions of 1P mode of ceiling and floor mount. resolutionC2P A list of 0/7 Available resolutions of 2P mode of ceiling and floor mount. resolutionC1R A list of 0/7 Available resolutions of 1R mode of ceiling and floor mount. resolutionC4R A list of 0/7 Available resolutions of 4R mode of ceiling and floor mount.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) eptz 0, 0/7 Indicate this mode whether support eptz. For "nvideoin" = 1, the definition is as following: A 32-bits integer, each bit can be set separately as follows: Bit 0 => 1st stream supports ePTZ or not. Bit 1 => 2nd stream supports ePTZ or not, and so on. For nvideoin >= 2, the definition is different: First all 32 bits are divided into groups for channel.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) outputsize 0/7 The output size of source, equal to the captured size by device, in this video mode. The unit is pixel. This value is used as a basic coordinate system for many features, like ePTZ, privacy mask, motion, etc. * Source (most for image sensor) may perform scale or binning, etc on image data, and output data with smaller size. This parameter is designed to represent this.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) minresolution A list of 0/7 Represent supported minimum resolution of each stream in current video mode. * The element number is defined as "capability_nmediastream". * We support this parameter when the version number (httpversion) is equal or greater than 0304b.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) maxfps_h264 A list of and "-" 0/7 Maximum fps which the device can encoded with H.264 on resolutions in this video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) Bit 1 => Supports Contrast or not. Bit 2 => Supports Saturation or not. Bit 3 => Supports Sharpness or not. Bit 4 => Supports adjusting the image to proper position horizontally or not. Bit 5 => Supports adjusting the image to proper position vertically or not. hlm 0/7 Hightlight Mask: The function will strengthen the image contrast and mask the specified zone of image if any strong spot-light exists.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) exposurelevel:hidd en:, exposurelevel:fixed :, exposurelevel:fixed :/, exposuremode:fixe d:auto, gammacurve:disabl affected functions are list here. The format is "Affect API name":"Policy":"Description" "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. ed:, exposurewin.mode .
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) be "-" wdrpro_description 0/7 Description about WDR Pro mode. * Only available when "capability_image_c<0~(n-1)>_wdrpro _mode" > 0 wdrc_mode 0, 1 0/7 0: Non-support WDR Enhanced 1: Support WDR Enhanced wdrc_supportlevel 0, WDR Enhanced.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL. For example: "exposurelevel:fixed:6/8/12" which means exposurelevel is fixed to level 6, level 8 and level 12. "-" means no feature is affected.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) * We support this parameter when the version number (httpversion) is equal or greater than 0302a. is_strength 0/7 0: Non-support tuning strength of image stabilizer mode. 1: Support tuning strength of image stabilizer mode. * Only available when "capability_image_c<0~(n-1)>_is_mod e" is not "-". * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) value. - (ranged) : UI is fixed to multiple selections or values. - (enabled) : UI is checked. - (notsupport) : the affected function is not available. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc: disabled:" which means blc exposure window is disabled. API name can be one word as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) panorama, manual, rbgain, widerange, outdoor,indoor, sodiumauto, iristype piris, dciris, - "-" means white balance is not supported. 0/7 Indicate iris type. "piris": P-Iris "dciris": DC-Iris "-": No Iris control support * Note: For some cameras, this value may be varied depending on mounted lens. sensortype rawsensor, smartsensor, 0/7 Indicate sensor type.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "twovalues": Need two parameters to indicate the exposure range. * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0302a. exposure_shuttervalu fixed, etype maximum, - 0/7 * One to one mapping to the mode type in "exposure_modetype".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) exposure_mode" is 1 and "capability_image_c<0~(n-1)>_exposu re_rangetype" is "onevalue". * We support this parameter when the version number (httpversion) is equal or greater than 0302a. exposure_automode_ affect -, exposurewin.mode .blc:hidden:, 0/7 When exposure auto mode is enabled, some features may become malfunction or be forced to a given defog:disabled:, wdrpro:disabled:, exposurelevel:hidd value.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) "Description" can be a nonnegative integer or string or NULL. "-" means no feature is affected. * Only available when auto is listed in "capability_image_c<0~(n-1)>_ exposure_modetype" and "capability_image_c<0~(n-1)>_ exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) which means blc exposure window is disabled. API name can be one word as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL. "-" means no feature is affected. * Only available when shutterpriority is listed in "capability_image_c<0~(n-1)>_ exposure_modetype" and "capability_image_c<0~(n-1)>_ exposure_mode" is 1.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) - (enabled) : UI is checked. - (notsupport) : the affected function is not available. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled. API name can be one word as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. - (enabled) : UI is checked. - (notsupport) : the affected function is not available. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) icrmode.auto:nots upport: or others : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) * When "exposure_mode"=0, this value must be set to "-". * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1. exposure_winmode exposure_meteringm ode auto, custom, blc, hlc, 0/7 Available options for "exposurewin_c<0~(n-1)>_mode" * "-" means group: exposurewin is not supported. center,
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. - (enabled) : UI is checked. - (notsupport) : the affected function is not available. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) control. "-": Not supported. * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1. exposure_windomain qvga, px, std, - 0/7 The domain to set an exposure window. "qvga": a 320x240 range to represent the whole image. "px": Locate a window in the image with pixels. "std": A normalized 0~9999 range. "-": Not supported. * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0301a. exposure_maxrange "1,32000", "1,8000", -, or others Available range for "videoin_c_maxexposure" "1,32000" => 1s ~ 1/32000s "1,8000" => 1s ~ 1/8000s etc. "-" means maximum exposure time is not available. * When "exposure_mode"=0, this value must be set to "-".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) different exposure values. * Only available when "capability_image_c<0~(n-1)>_ exposure_mode" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0310a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) “0,100” => 0~100 percent "-" means "videoin_c_maxgain" is not available. agc_mingain "0,100", "-" 0/7 Available range for "videoin_c_mingain" “0,100” => 0~100 percent "-" means "videoin_c_mingain" is not available. flickerless 0,1 0/7 0: Non-support flickerless 1: Support flickerless flickerlessaffect -, minexposure.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL. "-" means no feature is affected.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) - (enabled) : UI is checked. - (notsupport) : the affected function is not available. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled. API name can be one word as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Description" can be a nonnegative integer or string or NULL.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) focusassist 0,1 0/7 0: Non-support focus assist 1: Support focus assist remotefocus 0, 0/7 An 4-bit integer, which indicates the supportive application of remotefocus in this channel. If the value of this parameter is larger than 0, it means that the camera supports remotefocus function in this channel. bit 0 => Indicate whether to support both zoom and focus function.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) the version number (httpversion) is equal or greater than 0302a. autotrack_support 0/7 0: Non-support auto tracking feature 1: Support auto tracking feature * We support this parameter when the version number (httpversion) is equal or greater than 0302a. smartsensor_iristotalr ange A list of iris value 0/7 Available total step for iris value.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) ignment" is 1. lens_ldc_support 0/7 Indicate whether to support lens distortion correction function. * We support this parameter when the version number (httpversion) is equal or greater than 0309d. palette_support 0/7 Indicate support color palettes or not.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.28 Customized Event Script Group: event_customtaskfile_i<0~2> PARAMETER VALUE SECURITY (get/set) DESCRIPTION name string[40] 6/6 Custom script identification of this entry. date string[4~20] 6/6 Date of custom script. time string[4~20] 6/6 Time of custom script. 7.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) trigger boot, di, pir, motion, seq, recnotify, tampering, vi, volalarm, 6/6 Indicate the trigger condition: "boot" = System boot. "di"= Digital input. "pir"= PIR detection. "motion" = Video motion detection. "seq" = Periodic condition. "visignal" = Video input signal loss. "recnotify" = Recording notification. "tampering" = Tamper detection. "vi"= Virtual input (Manual trigger). "volalarm"= Audio detection.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) vi 0, 6/6 Indicate the source id of vi trigger. This field is required when trigger condition is “vi”. One bit represents one digital input. The LSB indicates VI 0. vadp 0, 6/6 Indicate the source id of vadp event notification. Each bit corresponds to one vadp source, and the LSB indicates source id 0.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) endtime hh:mm 6/6 End time of the weekly schedule. (00:00 ~ 24:00 sets schedule as always on) lowlightcondition 0, 1 6/6 Switch on white light LED in low light condition 0 => Do action at all times 1 => Do action in low-light conditions 6/6 Enable or disable trigger digital output.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) action_cf_backup 6/6 Enable or disable the function that send media to SD card for backup if network is disconnected. * Only available when "capability_supportsd" > 0 action_server_i<0~4>_en able 6/6 Enable or disable this server action. action_server_i<0~4>_m NULL, 0~4,101 edia 6/6 Index of the attached media.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) action_audioclip_media 0, 6/6 Indicate the source id of audioclip event notification. * Only avaliable when "capability_audio_audioclip" is 1. tampering 6/6 Indicate the source channel id of tampering detection. A 4-bit integer, each bit represents each channel. bit 0 => tampering detection for first 0, channel. bit 1 => tampering detection for second channel.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) ftp_username string[64] 6/6 Username to log in to the server. ftp_passwd string[64] 7/6 Password of the user. ftp_port 0~65535 6/6 Port to connect to the server. ftp_location string[128] 6/6 Location to upload or store the media. ftp_passive 6/6 Enable or disable passive mode. 0 = disable passive mode 1 = enable passive mode email_address string[128] 6/6 Email server address.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.31 Media Setting for Event Action Group: media_i<0~(n-1)> n denotes the value of "capability_media_num" (capability_media_num > 0) PARAMETER VALUE SECURITY DESCRIPTION (get/set) Name string[40] 6/6 Identification of this entry Type snapshot, systemlog, 6/6 Media type to send to the server or store on the server. 6/6 Indicate the source of media channel. 0 means the first channel. 1 means the second channel. 2 means the third channel.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) snapshot_datesuffix 0, 1 6/6 Add date and time suffix to filename: 1 = Add date and time suffix. 0 = Do not add. snapshot_preevent 0~" 6/6 capability_media_snapshot_ maxpreevent" Indicates the number of pre-event images. snapshot_postevent 6/6 0~" capability_media_snapshot_ Indicates the number of post-event images.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) videoclip_maxsize 338 - User's Manual 50 ~ " 6/6 capability_media_videoclip_ maxsize" Maximum size of one video clip file in Kbytes.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.32 Recording Group: recording_i<0~(n-1)> n denotes the value of "capability_nrecording" (capability_nrecording > 0) PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 Identification of this entry. trigger schedule, networkfail 6/6 The event trigger type schedule: The event is triggered by schedule networkfail: The event is triggered by the failure of network connection. enable 6/6 Enable or disable this recording.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) maxretentiontime 6/6 To specify the expired time for automatic clean up, and it only takes effect for video clip generated by recording_i <0~1>. Format is “‘P[Y]Y[MM]M[DDD]DT[hh]H[mm]M[ss] S’ , similar with ISO8601 with symbols P Ex. P7D, it means 7 days. P1DT10H, it means 1 days and 10 hours. The parameter takes effect when autocleanup_ maxretentiontime_recording_enabled is enabled.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) weekday 0~127 6/6 Indicate which weekday is scheduled. One bit represents one weekday. bit0 (LSB) = Saturday bit1 = Friday bit2 = Thursday bit3 = Wednesday bit4 = Tuesday bit5 = Monday bit6 = Sunday For example, to detect events on Friday and Sunday, set weekday as 66. begintime hh:mm 6/6 Start time of the weekly schedule. endtime hh:mm 6/6 End time of the weekly schedule.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) adaptive_enable 6/6 Indicate whether the adaptive recording is enabled adaptive_preevent 0~9 6/6 Indicate when is the adaptive recording started before the event trigger point (seconds) adaptive_postevent 0~10 6/6 Indicate when is the adaptive recording stopped after the event trigger point (seconds) 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) organizationname string[64] VIVOTEK Inc. 6/6 Organization name in the certificate information. unit string[64] VIVOTEK Inc. 6/6 Organizational unit name in thecertificate information. commonname string[64] www.vivotek.com 6/6 Common name in the certificate information. validdays 0 ~ 3650 6/6 Valid period for the certification. 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) autocleanup_enabled 6/6 Enable automatic clean up method. Expired and not locked media files will be deleted. * For forward compatibility reservations, but only group disk_i0_autocleanup is effective. * Not recommended to use this. Please refers "autocleanup" group.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.35 Region of Interest Group: roi_c<0~(n-1)> for n channel product and m is the index of video stream which support ePTZ. (capability_eptz > 0 or capability_fisheye = 1) PARAMETER VALUE SECURITY (get/set) DESCRIPTION s<0~(m-1)>_home 1/6 ROI left-top corner coordinate.* If the minimal window size is 64x64, then the "win_i0_home"=(0~resolution_W-64, 0~resolution_H-64), which the resolution is the value in current stream.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.36 ePTZ Setting Group: eptz_c<0~(n-1)> for n channel product. (capability_eptz > 0 or capability_fisheye = 1) PARAMETER VALUE SECURITY (get/set) DESCRIPTION osdzoom 1/4 Indicates multiple of zoom in is “on-screen display” or not. * Reserved for compatibility, and suggest don't use this since [httpversion] > 0302a * We replace "eptz_c<0~(n-1)>_osdzoom" with " videoin_c<0~(n-1)>_zoomratiodisplay".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) rotatespeed 1~5 1/7 Auto pan/patrol speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) 1/7 Width and height of the preset. (It should be set by ePreset.cgi rather than by setparam.cgi.) 7.37 Focus Window Setting Group: focuswindow_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin". (capability_image_c<0~(n-1)>_focuswindow_nwindow > 0) PARAMETER VALUE SECURITY (get/set) DESCRIPTION win_i0_enable 4/4 Enable or disable the window.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.38 Seamless Recording Setting Group: seamlessrecording (capability_localstorage_seamless> 0) PARAMETER VALUE SECURITY (get/set) diskmode seamless, 1/6 manageable DESCRIPTION “seamless” indicates enable seamless recording. “manageable” indicates disable seamless recording. * We replace this parameter with “seamlessrecording_c<0~(n-1)>_diskmode” when the version number (httpversion) is equal or greater than 0312a.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) guid<0~2>_number 0~3 1/7 Number of connected seamless streaming with guid<0~(k-1)>_id. (Read only) * We replace this parameter with “seamlessrecording_c<0~(n-1)>_guid<0~2>_n umber” when the version number (httpversion) is equal or greater than 0312a. 7.38.1 Seamless recording setting per channel Group: seamlessrecording_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin".
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved guid<0~(k-1)>_id string[127] 1/7 The connected seamless streaming ID. (Read only) * k denotes the value of "seamlessrecording_c<0~(n-1)>_maxco nnection" * We support this parameter when the version number (httpversion) is equal or greater than 0312a. guid<0~(k-1)>_number 0~3 1/7 Number of connected seamless streaming with guid<0~(k-1)>_id.
VIVOTEK NAME © 2019 VIVOTEK INC. All Right Reserved VALUE SECURITY DESCRIPTION (get/set) saved to SD card when user want to upload it. If the value is false, save module to the internal storage space and it will occupy storage size. number 352 - User's Manual string[128] 6/7 This number is used to register license key for VADP application.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Group: vadp_module_i<0~(n-1)> for n VADP package number (capability_vadp_npackage > 0) n denotes the value of "capability_vadp_npackage". NAME VALUE SECURITY (get/set) DESCRIPTION enable 6/6 Indicate if the module is enabled or not. If yes, also add the index of this module to the module_order. name string[40] 6/6 Module name extendedname string[40] 6/6 Extended module name.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the schedule mode to control the execution of the VADP package begintime hh:mm 6/6 Begin time of the schedule endtime hh:mm 6/6 End time of the schedule VALUE SECURITY DESCRIPTION Group: vadp_event NAME (get/set) ntrigger 0, 6/7 Indicate the number of topics to be transferred to event manager for trigger.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) The dwelling time of each patrol point, separated by “,” * only available when capability_camctrl_c0_rs485=2 preset_i<0~(k-1)>_nam e string[40] 1/4 Name of the preset location. preset_i<0~(k-1)>_ dwelling 0 ~ 999 1/4 The dwelling time of each preset location * only available when capability_camctrl_c0_rs485=2 uart 0~" capability_nuar t"-1 1/4 Select corresponding uart (capability_nuart>0).
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) rt"-1 isptz 0~2 preset_i<0~(k-1)>_name string[40] * only available when capability_camctrl_c0_rs485=2 1/4 0: disable PTZ commands. 1: enable PTZ commands with PTZ driver. 2: enable PTZ commands with UART tunnel. * only available when capability_camctrl_c0_rs485=2 1/4 Name of the preset location.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) The dwelling time of each patrol point, separated by “,” * only available when capability_camctrl_c0_rs485=2 disablemdonptz 1/4 Disable motion detection on PTZ operation. defaulthome 1/4 This field tells system to use default home position or not. axisz capability_ptz_ 1/4 c<0~(n-1)>_min zoom ~ capability_ptz_ c<0~(n-1)>_ma xzoom Custom home zoom position.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) n-1)>_minpan ~ capability_ptz_c<0~( n-1)>_maxpan location. preset_i<0~(k-1)>_tilt capability_ptz_c<0~( n-1)>_mintilt ~ capability_ptz_c<0~( n-1)>_maxtilt 1/4 Tilt position at each preset location. preset_i<0~(k-1)>_zoom capability_ptz_c<0~( n-1)>_minzoom ~ 1/4 Zoom position at each preset location.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) n-1)>_maxpan axisy capability_ptz_c<0~( n-1)>_mintilt ~ capability_ptz_c<0~( n-1)>_maxtilt 1/4 Custom home tilt position. axisz capability_ptz_c<0~( n-1)>_minzoom ~ capability_ptz_c<0~( n-1)>_maxzoom 1/4 Custom home zoom position. axisf capability_ptz_c<0~( n-1)>_minfocus ~ capability_ptz_c<0~( n-1)>_maxfocus 1/4 Custom home focus position. axisflip 1/4 Custom home flip side.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) Recorded tour: unnecessary. tour_i<0~19>_direction forward,backward,ra ndom 1/4 User can choose which direction the preset tour goes. "forward": preset tour goes in forward order. "backward": preset tour goes in backward order. "random": the presets of the tour will be recalled randomly. * Only available when "capability_presettourdirection" is 1.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.43 UART Control Group: uart (capability_nuart > 0 and capability_fisheye = 0) NAME VALUE SECURITY (get/set) DESCRIPTION ptzdrivers_i<0~19, 127>_name string[40] 1/4 Name of the PTZ driver. ptzdrivers_i<0~19, 127>_location string[128] 1/4 Full path of the PTZ driver. enablehttptunnel 1/4 Enable HTTP tunnel channel to control UART.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) speedlink_i<0~4>_n ame string[40] 1/4 Additional PTZ command name. * only available when capability_camctrl_c0_rs485=2 speedlink_i<0~4>_c md string[40] 1/4 Additional PTZ command list. * only available when capability_camctrl_c0_rs485=2 ptzdriver 0~19, 127 (custom), 128 (no driver) 1/4 The PTZ driver is used by this COM port. * only available when capability_camctrl_c0_rs485=2 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) stopbit 1,2 4/4 "1": One stop bit is transmitted to indicate the end of a byte. "2": Two stop bits are transmitted to indicate the end of a byte. If you want to transfer the stopbit for 150% of the normal time used to transfer one bit, the uart_i<0~(n-1)>_stopbit should be set as 2 and the uart_i<0~(n-1)>_databit set as 5 as well. uartmode rs485 4/7 RS485 mode. 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Group: lens_default_i<0~(n-1)> n denotes the value of "lens_default_totalnumbers" NAME VALUE SECURITY (get/set) DESCRIPTION name 6/7 Default lens name Group: lens_user_i<0~(n-1)> n denotes the value of "lens_user_totalnumbers" NAME VALUE SECURITY (get/set) DESCRIPTION name 6/7 User-defined lens name 7.46 Fisheye Info.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved NAME VALUE SECURITY DESCRIPTION (get/set) [0~359]. Pan range of wall mount is [-90~90]. s<0~(m-2)>_region_t -90~90 ilt 1/4 Tilt home angle of regional view Tilt range of ceiling/floor mount is [0~90]. Tilt range of wall mount is [-90~90]. s<0~(m-2)>_region_ zoom 1/4 Zoom home ratio of regional view 100~300 PLEASE REFER TO FISHEYE LOCAL DEWARP API 7.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 7.50 Wireless Group: wireless (capability_network_wireless > 0) PARAMETER VALUE SECURITY (get/set) DESCRIPTION ssid string[32] 6/6 SSID for wireless lan settings. wlmode Infra, Adhoc 6/6 Wireless mode. Infra: Infrastructure channel 1~11 or 6/6 A list of WLAN channels. Countries apply their own regulations to the allowable channels.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE SECURITY DESCRIPTION (get/set) key1 password [26] 6/6 WEP key1 for encryption. * Only valid when "wireless_encrypt" is "wep" key2 password [26] 6/6 WEP key2 for encryption. * Only valid when "wireless_encrypt" is "wep" key3 password [26] 6/6 WEP key3 for encryption. * Only valid when "wireless_encrypt" is "wep" key4 password [26] 6/6 WEP key4 for encryption.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8. Useful Functions 8.1 Drive the Digital Output (capability_ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: [&do2=] [&do3=][&do4=] Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved [di3=]\r\n where can be 0 or 1. Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n 8.3 Query Status of the Digital Output (capability_ndo > 0) Note: This request requires Viewer privileges Method: GET/POST Syntax: http:///cgi-bin/dido/getdo.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n 8.4 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/video.jpg?[channel=][&resolution=] [&quality=][&streamid=] If the user requests a size larger than all stream settings on the server, this request will fail.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 8.5 Account Management Note: This request requires Administrator privileges. Method: POST Syntax: http:///cgi-bin/admin/editaccount.cgi? method=&username=[&userpass=][&privilege=] [&privilege=][&return=] PARAMETER VALUE DESCRIPTION method add Add an account to the server. When using this method, the“username” field is necessary. It will use the default value of other fields if not specified.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.6 Upgrade Firmware Note: This request requires Administrator privileges. Method: POST Syntax: http:///cgi-bin/admin/upgrade.cgi Post data: fimage=[&return=]\r\n \r\n Server will accept the file named to upgradethe firmware and return with if indicated.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.7 ePTZ Camera Control (capability_eptz > 0 and Capability_fisheye = 0) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/eCamCtrl.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved b. continuous movement If you trigger a continuous movement, you have to handle the stop time by yourself. A continuous movement is convenient to integrate a joystick control. http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zooming=tele&zs=1 http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zooming=wide&zs=5 zooming is used to indicate the moving direction, and zs is used to indicate the speed.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION y movement w The scaled area size h resolution The resolution of streaming. vx The direction of movement, used for joystick control. vy vs 0~7 Set the speed of movement, “0” means stop. x x-coordinate clicked by user. It will be the x-coordinate of center after movement. y y-coordinate clicked by user.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.8 ePTZ Recall (capability_eptz > 0 and capability_fisheye = 0) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/eRecall.cgi?channel=&stream=& recall=[&return=] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stream. recall Text string less than 40 characters One of the present positions to recall.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION addpos delpos return Redirect to the page after the parameter is assigned. The should be the relative path according to the root of camera. If you omit this parameter, it will redirect to an empty page.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.11 UART HTTP Tunnel Channel (capability_nuart > 0) Note: This request requires Operator privileges. Method: GET and POST Syntax: http:///cgi-bin/operator/uartchannel.cgi?[channel=] ------------------------------------------------------------------------GET /cgi-bin/operator/uartchannel.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.12 Event/Control HTTP Tunnel Channel (capability_evctrlchannel > 0) Note: This request requires Administrator privileges. Method: GET and POST Syntax: http:///cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------GET /cgi-bin/admin/ctrlevent.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.13 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET/POST Syntax: http:///_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp” for setting the accessname of SDP. You can get the SDP by HTTP GET.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 8.15 Send Data (capability_nuart > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/senddata.cgi? [com=][&data=][&flush=] [&wait=] [&read=] PARAMETER VALUE DESCRIPTION com 1 ~ The target COM/RS485 port number. data is a series of digits from 0 ~ 9, A ~ data>[,
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.16 Storage Managements (capability_stroage.dbenabled > 0) Note: This request requires administrator privileges. Method: GET and POST Syntax: http:///cgi-bin/admin/lsctrl.cgi?cmd=[&=…] The commands usage and their input arguments are as follows. PARAMETER VALUE DESCRIPTION cmd_type Required. Command to be executed, including search, insert, delete, update, and queryStatus.
© 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE VIVOTEK DESCRIPTION Ex. resolution=’800x600’ isLocked Optional. Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage. triggerTime Optional. Indicate the event trigger time. (not the file created time) Format is “YYYY-MM-DD HH:MM:SS” Please embrace your input value with single quotes. Ex.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE DESCRIPTION Ex. label=1 Ex. Delete records whose key numbers are 1, 4, and 8. http:///cgi-bin/admin/lsctrl.cgi?cmd=delete&label=1&label=4&label=8 Command: update PARAMETER VALUE DESCRIPTION label Required. Identify the designated record. Ex. label=1 isLocked Required. Indicate if the file is locked or not. Ex. Update records whose key numbers are 1 and 5 to be locked status.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.17 Virtual Input (capability_nvi > 0) Note: Change virtual input (manual trigger) status. Method: GET Syntax: http:///cgi-bin/admin/setvi.cgi?vi0=[&vi1=][&vi2=] [&return=] PARAMETER VALUE vi state[(duration)nstate] Ex: vi0=1 Where "state" is 0, 1. “0” Setting virtual input 0 to trigger state means inactive or normal return DESCRIPTION state while “1” means active or triggered state.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Examples: setvi.cgi?vi0=0(15000)1 setvi.cgi?vi0=1 Request 2 will not be accepted during the execution time(15 seconds). 8.18 Open Timeshift Stream (capability_timeshift > 0, timeshift_enable=1, timeshift_c_s_allow=1) Note: This request requires Viewer access privileges.
© 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DEFAULT VIVOTEK DESCRIPTION ignored. reftime mm:ss The time camera receives the request. Reference time for maxsft and minsft. (This provides more precise time control to eliminate the inaccuracy due to network latency.) Ex: Request the streaming from 12:20 rtsp://10.0.0.1/live.sdp?maxsft=10&reftime=12:30 forcechk N/A N/A Check if the requested stream enables timeshift, feature and if minsft is achievable.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.19 RemoteFocus (capability_image_c<0~(n-1)>_remotefocus=1) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/remotefocus.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK PARAMETER VALUE DESCRIPTION function Function type zoom - Move focus motor focus – Move focus motor auto – Perform auto focus scan – Perform focus scan stop – Stop current operation positioning – Position the motors irisopen – Fully open iris. It will maintain fully open iris status until sending function=irisenable cgi. irisenable – return back to user setting status of iris.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION direction direct, forward, backward Motor’s moving direction. It works only if function=zoom or function=focus. position 0~ Motor’s position. It works only if function=zoom or function= focus and direction=direct. is refer to remote_focus_focus_motor_max or remote_focus_zoom_motor_max which replied from "function=getstatus" steps 1 ~ Motor’s moving steps.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.20 BackFocus (capability_image_c<0~(n-1)>_remotefocus=4) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/remotefocus.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION function focus, auto, scan, stop, positioning, irisopen, irisenable, resetfocus, getstatus Function type focus – Move focus motor auto – Perform auto focus scan – Perform focus scan stop – Stop current operation positioning – Position the motors resetfocus – reset focus position to default irisopen – Fully open iris. It will maintain fully open iris status until sending function=irisenable cgi.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION position 0~ Motor’s position. It works only if function=focus and direction=direct. is refer to remote_focus_focus_motor_max which replied from "function=getstatus" steps 1 ~ Motor’s moving steps. It works only if function=focus and direction=forward or direction=backward.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.22 Upload Files Note: This request requires Administrator privileges. Method: POST Syntax: For daylight saving time configuration file: http:///cgi-bin/admin/upload_dst.cgi Post data: filename =\r\n \r\n For language file: http:///cgi-bin/admin/upload_lan.cgi Post data: filename =\r\n \r\n For setting backup file: http:///cgi-bin/admin/uploa
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 8.23 Update Lens Configuration (capability_image_c<0~(n-1)>_lensconfiguration_support > 0) Note: This request requires Administrator privileges. Method: GET Syntax: For list a name of lens currently used: http:///cgi-bin/admin/update_lens.cgi?get_currentlens For list all names of lens installed in camera: http:///cgi-bin/admin/update_lens.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Post data: upload_lens_profile_input = \r\n \r\n Server will accept the file named to upload the lens profile to camera. 8.24 Media on Demand (capability_localstorage.modnum > 0) Media on demand allows users to select and receive/watch/listen to metadata/video/audio contents on demand. Note: This request requires Viewer access privileges. Syntax: rtsp:///mod.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved rtsp://10.10.1.2/mod.sdp?etime=20110312_040400.000&length=120 X X X V Play file file rtsp://10.10.1.2/mod.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.25 Fisheye Local Dewarp Camera Control (capability_fisheye > 0 and capability_fisheyelocaldewarp.c0 > 0, only support in 1R mode) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/fdCamCtrl.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION left Move left. right Move right. wide Zoom larger view with current speed. tele Zoom further with current speed. speedpan -5 ~ 5 Set the pan speed of current command. speedtilt -5 ~ 5 Set the tilt speed of current command. speedzoom -5 ~ 5 Set the zoom speed of current command. zooming wide or tele Zoom without stopping for larger view or further view with zoom zs speed, used for joystick control.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.26 3D Privacy Mask (Capability_image_c<0~(n-1)>_privacymask_wintype = 3Drectangle) n denotes the value of "capability_nvideoin" Note: This request requires admin user privilege Method: GET/POST Syntax: http:///cgi-bin/admin/setpm3d.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.27 Camera Control (capability_camctrl_c<0~(n-1)>_zoommodule = 1) Note: This request requires Viewer privileges. Method: GET/POST Syntax: (for control API) http:///cgi-bin/camctrl/camctrl.
VIVOTEK PARAMETER © 2019 VIVOTEK INC. All Right Reserved VALUE DESCRIPTION down Move camera down. left Move camera left. right Move camera right. speedpan -5 ~ 5 Set the pan speed. speedtilt -5 ~ 5 Set the tilt speed. speedzoom -5 ~ 5 Set the zoom speed. speedfocus -5 ~ 5 Set the focus speed. speedapp -5 ~ 5 Set the auto pan/patrol speed. auto pan Auto pan. patrol Auto patrol. stop Stop camera. wide Zoom larger view with current speed.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION focus auto Auto focus. far Focus on further distance. near Focus on closer distance. sync Applies the selected focus mode in camctrl_c<0~(n-1)>_focusmode to this preset. fixcurrent Applies the current focus position to this preset. focusseting * We support this function when the version number of the PTZ control module is equal or greater than 5.0.0.20.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION getpanangle Get the current pan angle. *Only available when bit0 of "capability_camctrl_c<0~(n-1)>_buildinpt" is "1" gettilt 0, Get the current tilt position. *Only available when bit1 of "capability_camctrl_c<0~(n-1)>_buildinpt" is "1" gettiltangle getzoom 0, Get the current zoom position.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION "capability_camctrl_c<0~(n-1)>_buildinpt" is "1" getmintiltangle Get the lower limit for tilt angle. *Only available when bit1 of "capability_camctrl_c<0~(n-1)>_buildinpt" is "1" getmaxtiltangle Get the upper limit for tilt angle. *Only available when bit1 of "capability_camctrl_c<0~(n-1)>_buildinpt" is "1" getminzoom 0, Get the lower limit for zoom position.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.29 Preset Locations (capability_camctrl_c<0~(n-1)>_zoommodule = 1) Note: This request requires Operator privileges. Method: GET/POST Syntax: http:///cgi-bin/operator/preset.cgi?[channel=] [&addpos=][&delpos=][&return=] PARAMETER VALUE DESCRIPTION addpos string[30] Add one preset location to the preset list. channel 0~"capability_nvideoin"-1 Channel of the video source.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 8.30 SmartSD (capability_localstorage_smartsd > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/smartsd.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION function getstatus Function type getstauts : Information of smartSD internal status return value as below: smartsd_lifetime_num: Accumulated amount of data that has been written smartsd_lifetime_den: Card-guaranteed amount of data that can be written smartsd_lifetime_rate: The ratio of smartsd_lifetime_num to smartsd_lifetime_den. It means the accumulated percentage amount of flash block has been written.
© 2019 VIVOTEK INC. All Right Reserved VIVOTEK 8.31 Connect to AP (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/connect_ap.cgi PARAMETER VALUE DESCRIPTION N/A N/A Apply the wireless settings and connect to AP. 8.32 Get Wireless Information (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/getwirelessinfo.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.33 Get Wireless Signal Strength (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/getwlsignalstrength.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved PARAMETER VALUE DESCRIPTION N/A N/A Get wireless signal strength. 8.34 WPS Transaction (capability_network_wireless > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/start_wps.cgi PARAMETER VALUE DESCRIPTION N/A N/A Start WPS transaction. 8.35 Peripheral Control (capability_peripheral_c<0~(n-1)>_ devicecontrol > 0) Note: This request requires Administrator privileges.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved "washer_mode : OK\r\n" "washer_status : FAIL\r\n" PARAMETER VALUE DESCRIPTION channel 0~"capability_nvideoin"-1 Channel of the video source. washer_mode wiper Apply the wiper to the mode of washer control system. washer Apply the washer to the mode of washer control system. on Enable the functionality of washer control washer_status system. washer_dwelltime off Disable the functionality of washer control system.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Pragma: no-cache\r\n \r\n supportdevice=washer,heater\r\n washer_status=off\r\n PARAMETER VALUE DESCRIPTION channel 0~"capability_nvideoin"-1 Channel of the video source. supportdevice N/A Get support peripheral device. washer_supportmode N/A Get the support mode of washer control system. washer_mode Get the current mode of washer control system.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved 8.36 Optimized IR control (capability_daynight_c<0~(n-1)>_optimizedir > 0) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/optimizedir.cgi?function=[&channel=] PARAMETER VALUE DESCRIPTION channel 0~"capability_nvideoin"-1 Channel of the video source. function getstatus, onetimeauto "onetimeauto": Camera will automatically adjust the IR zone one time only.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved http://myserver/cgi-bin/admin/optimizedir.cgi?function=getstatus Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n "optimizedir_c0_irmode='auto'" "optimizedir_c0_irnum='5'" "optimizedir_c0_irstrength='1,97,100,100,100'" "optimizedir_c0_irstatus='normal'" Syntax: (for control API) http:///cgi-bin/admin/optimizedir.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Example: http://myserver/cgi-bin/admin/optimizedir.cgi?channel=0&operation=settoall&irmode=manual&str ength=100 Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n "optimizedir_c0_irstrength='100,100,100,100,100'" "optimizedir_c0_irmode='manual'" Example: http://myserver/cgi-bin/admin/optimizedir.cgi?channel=0&operation=set&irmode=auto&strength= 50,70,50,50,50 Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved http:///cgi-bin/admin/optimizedir.cgi?channel=&operation=get [&support_irmode] – list all adjustment mode that IR supports [&irmode] – Get current IR mode [&irnum] – Get the number of IR zone PARAMETER VALUE DESCRIPTION channel 0~"capability_nvideoin"-1 Channel of the video source. support_irmode N/A List all adjustment mode that IR supports irmode N/A Get the current IR control mode.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved \r\n OK Example: http://myserver/cgi-bin/admin/thermalctrl.cgi?operation=set&action=shuttercompensate Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n ERROR: time out Example: http://myserver/cgi-bin/admin/thermalctrl.cgi?operation=set&action=shuttercompensate Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n ERROR: fail PARAMETER VALUE DESCRIPTION action shuttercompensate Camera will
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved Response: HTTP/1.0 200 OK\r\n Cache-control: no-cache\r\n Pragma: no-cache\r\n \r\n version=1120B15 8.38 Audio Clip Control (capability_audio_audioclip=1) Note: This request requires Administrator privileges. Method: GET/POST Syntax: (for control API) http:///cgi-bin/admin/audioclip.
VIVOTEK © 2019 VIVOTEK INC. All Right Reserved clipname Name of the audio clip. clipindex 0, 1 Number of the audio clip.
VIVOTEK Technology License Notice AMR-NB Standard THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING LICENSORS’ PATENTS MAY APPLY: TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938; 6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION: AT PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621; DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT.
VIVOTEK Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. ■ This device may not cause harmful interference, and ■ This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
