English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera.
Quick Installation Guide IP8361 Network Bullet Camera English Français Software CD Quick Installation Guide 繁中 簡中 日本語 Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska 2MP • Outdoor • Day & Night Cable Management 5 1 0 0 0 02 2 1 G Warranty Card 2 Physical Description Lens IR LED Light Sensor SD/SDHC/SDXC Card Slot General I/O Terminal Block Reset Button Status LED Power Cord Socket RJ45 Cable EN-2
English 3 Hardware Installation 1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Fix the intersection bracket to the side of the Network Camera with two screws. 3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next page.) 4.
Waterproof Connector Components of the Waterproof Connector Pin Definition Screw Nut (A) Seal (B) Seals (C) 1 2 3 4 5 6 7 8 Housing (D) Sealing Nut (E) 1 2 3 4 5 6 7 8 Power +12V Digital Output Digital Input Ground AC 24V AC 24V RS485 + RS485 - 1 2 3 4 External MIC In Ground Audio Out Ground 1 2 3 4 Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above. 2. Open the back cover of the Network Camera. 3.
English 4 Cabling Assembly RJ45 Cable Connector Components of the Waterproof Connector RJ45 Cable Dimension (unit: mm) Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps 1 Prepare an Ethernet cable and strip part of the sheath. 2 Insert the housing into the screw nut. (C) 3 (D) Insert the seal into the housing. (B) Recommended cable gauge: 24AWG (0.51 mm) 4 Insert the stripped Ethernet cable through the sealing nut and the housing.
5 Network Deployment Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
English 6 Assigning an IP Address 1. Install "Installation Wizard 2" from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller. 4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the focus controller. T N 3 4 W ∞ 5. Tighten the lens cover. 6. Open the back cover. 7. Tear down the aluminum foil vacuum bag and take out the dessicant bag. Attach the silica gel to the inner side of the back cover, then tighten the back cover.
English 8 Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations. Please visit VIVOTEK's official website for more purchase information. Pole Mount Bracket Corner Mount Bracket IR illuminator (distance 30m, 60°) ° 60 5° 3 Built-in 24 LED units (distance 25m, 35°) The 30m, 60° IR illuminator extends the coverage of the Network Camera and reduces the halo effect around captured images.
