IP8332-C Bullet Network Camera Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский P/N:625018500G Rev. 1.0 Outdoor • Day & Night • Weather-proof • Cable Management All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user’s manual for the operating temperature. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera. Replacing or failing to properly install the waterproof components, e.g.
2 Physical Description Front Panel Lens IR LEDs Light Sensor Rear Panel Reset Button MicroSD/SDHC Card Slot Connectors General I/O Terminal Block Ethernet 10/100 RJ45 Plug Power Cord Socket (Black) EN-2
English 3 Hardware Installation If you prefer installing a MicroSD card as onboard storage: 1. Loosen the waterproof connector, and then remove the rubber seal, and the waterproof connector. 2. Loosen and open the rear cover. 3. Install a MicroSD/SDHC card. 4. Tear down the aluminum foil vacuum bag and take out the dessicant bag. Attach the supplied dessicant bag to the inner side of the Network Camera. (Please replace the dessicant bag with a new one every time you open the rear cover.) 5.
. Tighten the rear cover, rubber seal and waterproof connector. 5 6. Pass the cables through the center of the ball swivel mount bracket, one at a time. 7. Fasten the bracket to the camera using 3 hex socket screws. NOTE: 7 The camera weighs up to 1.28 kgs. Make sure the mounting surface can support this camera. 6 8. Loosen the fastening ring on the mount bracket, and aim the camera at the area of your interest. When done, tighten the fastening ring.
English 9. Secure the Network Camera to a wall or ceiling. Ceiling Mount 9 4 Wall Mount Network Deployment General Connection (without PoE) 1. If you have external devices such as sensors and alarms, make connections from general I/O terminal block. GND DI AC24V AC24V GND DI AC24V AC24V : Ground : Digital Input : 24V: 24V+ POWER 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION 3.
Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
English 5 Assigning an IP Address 1. Install the "Installation Wizard 2" from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
6 Secure the Shooting Angle When you are done with tuning the field of view and obtain a satisfactory image, tighten the fastening ring and the 3 small hex screws on the ball-swivel bracket. NOTE: Orient the camera so that the protruding edge of its sunshield is positioned against the direction of direct sunlight.
IP8332-C Bullet Network Camera Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский P/N:625018500G Rev. 1.0 Outdoor • Day & Night • Weather-proof • Cable Management All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.
